Counting matching models…
One of the first tool purchases i did when i became a plastics processing technician apprentice was a Mitsutomo unbraco keyset for tool changes. Carrying the set in my hammer loop has worn the rubber to the point of i-can't-be-arsed…
Consider this a first revision of a keycap design i have been working on. I have found it necessary to begin anew with the knowledge from this version. Print Settings Printer: Ormerod 2 528.4 Supports: Yes Resolution: 0.1mm Infill: n/a…
Dust cover for male DVI connectors usually found on graphics card and adapters. The print will fit tightly and will benefit from being printed in a soft ish filament. (Not TPE not PLA) Print Settings Printer Brand: RepRap Printer: Ormerod…
i designed this as a joke i cannot stress that enough. Do you want to make your impotent blower bring home the bread and turn heads? Then print this velocity stack for your 5015 fan to achieve that hotrod look, K&N filter not included…
This headphone hanger uses a subtly curved design and exported at an overly high resolution for a smoother curve to avoid adding bumps into the headband. The three holes have a decorative relief for an ifixit screwdriver and can…
With a desire to overcomplicate a ziptie jobbo i decided to procrastinate and make a thing that would let me attach a 19" 1U powerstrip to my skådis plate. It uses the skadis nuts to mount to the plate and has a nifty hole in the back to…
both bumpers and buttons are in the same file and need to be separated in your slicer of choice, if not cura has a tree like support that works well. This print was done in prusa slicer in filaflex 40 with hexagon infill as opposed to…
To remove the potential factor of the bowden tube moving about i made a retaining clip with a similar thickness to the distance between the bowden coupling and the aluminium surface, thus making it necessary to remove the retaining clip…
After spending some time looking for how to mount full extension drawer slides on the ikea helmer drawer unit i decided to divert my time towards a possible solution i could do that day. the design is optimized for vasemode with a 0.4mm…
## Use ironing on the contacting surface between the charger and the print to ensure that the charger sits flush ## This overdesigned magsafe (Spigen ArcField MagSafe) to skådis is made with slimness in mind. The back piece is only thick…
This is an print of mine for the kensington orbit trackball. The purpose was to have an extra row of buttons next to my fingers which i could apply common shortcuts to. To get the correct spacing between my finger and the row of keys i…
Made from measurements given to me, with a 1.5" lift. I designed it around having it on the left side of the keyboard, if you are interested in a right handed version your slicing software will have a mirroring feature. Category: Other
the bushings should fit the intake manifold of a vr5 20v engine circa 2003, this engine came in the bora, golf and jetta mk4, they were printed in ABS at 100% infill and scaled up to the shrinkage of my current spool (100.37 in…
for mounting with tesa adhesive screws 2.5kg (77902-00002-00) there is 8cm between the wall to the center of the rod. I have uploaded two variants, Ø15mm and Ø20mm to deliver a more flush look for the Räcka curtain rod that i intended to…
Bauhaus sells a small parts organizer made by the Lockweiler company but under the Wisent brand. The wall dividers to the boxes are costly and I found a need for removable sorting boxes for assorted screws. Print Settings Printer Brand:…
To add fine tuning to my drone i came to the conclusion that merely elongating my thumb sticks i could achieve this with minimal work required. Its designed around a Ø15mm thumb stick with a 12mm radii. I assume this will fit any micro…
The parts where fans are mounted should be printed with that contacting face against the build plate. The segment that is mounted onto the original ormerod holder should be printed on its back. After having spent too much time editing…
So while procrastinating with a project on how to better store pencils i came to the realization that a baseplate would be a quick and easy project to do instead. The two sides shouldn't be occupied when closing the pencil case as the…
I blatantly ripped off the ergodox tenting stand https://github.com/Ergodox-io/ergodox-tent so i could put in a shelf for the amazon basics four port usb hub. addendum. I have experienced tolerance issues with my .4mm print with the top…
To avoid the unsightly mess of cables dangling around like behind your computer (yes yours) i have made two "end points" for the cables feeding up onto the x axis. Bill of Materials: "X axis stepper motor" 3 M3 x 35mm cap 10 x 15mm drag…
To avoid having my charging cable laying everywhere i chose to design thos cable holder that would sit relatively snugly around the body of the usb housing. Print Settings Printer: Ormerod 2 528.4 Rafts: No Supports: No Resolution: 0.2mm…
The ormerod 2 comes with an acrylic piece (781) to attach a cooling fan. Sans shroud i decided to put it to use and design my own for use together with a 40x40x10 akasa fan. Print Settings Printer: Ormerod 2 528.4 Rafts: Doesn't Matter…
In the pursuit of a better alternative to the M5 lead screw i saw that acme lead screws have come down in price due to higher demand. After figuring out how to implement this upgrade i came up with this design. This upgrade requires three…
I can't keep the filament wrapped snugly against the 2kg reel since its out of balance. To avoid the unwound filament to wrap around the hub and snag i felt it necessary to procure a guide that i can easily change the position of. Print…
These are all currently available results.
