Counting matching models…
This is the same model as the Ender NG v1.2 toolhead base, but with a reinfocement bar added in the middle. This part is under a lot of stress with the belts. Combine this with higher tension, high-speed printing, and a heated chamber,…
Here's a fancy set of 4010 tool heads based off the updated CFD-tuned air ducts! This model adds an Ender NG logo cutout over the fan as a fancy grill. I also fixed the stringy bridges in the lower vent by reshaping the duct (see…
This is a toolhead accessory cable mount and breakout the includes a configuration designed for using a Klicky sensor. I included connectors for every toolhead accessory, including the extruder and hot end heater. The hot end heaters can…
Here's a DIN rail mount for a BTT SKR Mini E3 V3.0! It's a little cleaner-looking than the original (in my opinion), and it mounts the board 6.5 mm lower than the original. This leaves more room for the upper DIN rail, and also allows you…
This is a separate logo model for the Ender 3 NG v1.2 electronics panel! Scale the Z axis in your slicer to add a custom depth. The print in the photo is about 50% height. Instead of bothering with multi-color prints, print the…
This is a reinforced ProtoXtruder 2.0 designed as a bolt-on upgrade for the Ender 3 NG v1.2! It's designed to survive the stress of high-temperature heated chambers, has a PC4-M6 fitting, and uses more parts from the Ender 3 NG v1.2 BOM.…
This mod for the Ender 3 NG v1.2 allows you to add PC4-M6 fittings to easily add and remove tubing to the enclosure v2 lid corners. There are a handful of files in this model, which includes: PC4-M6 fittings, left corner PC4-M6 fittings,…
The Ender 3 NG v1.2 has three DIN rails in the electronics panel. On most builds, the lower rail is mostly occupied by the power supply, and the middle one is where most other electronics go, like the SoC module (i.e. a Raspberry Pi) and…
When homing, the Y gantry hits the Y endstop microswitch. This endstop has a tendency to come loose and twist, especially in a heated chamber. When this happens, the Y will calibrate at a further distance than intended. Probes typically…
This is a bolt-on spool holder with an integrated load cell for the Ender 3 NG v1.2! It replaces a couple of the enclosure pads on either side of the printer and offers a spool holder with the same look as the rest of the printer. Don't…
Here is a PT100/PT1000 thermistor mount for an Ender 3 NG v1.2! It is designed to have a look similar to the Ender 3 NG v1.2's original parts. There's a cable tunnel on the back that gently holds the thermistor in-place with its own…
This is an enclosure and mount for a PTCYIDU PTC heater and fan. It is designed to be mounted to a two-slot aluminum extrusion rail using M4 T-nuts and screws. All parts can be rotated 180 degrees so that the heater and the cable can be…
The original toolhead accessories cable does not include the hole in this model, which means that the cables have to be wrapped around the side of the mount. This isn't very elegant, and it would make a lot more sense for the cables to go…
Want a two-screw endstop that holds the microswitch in a position that accommodates tools? Use this model instead! When homing, the Y gantry hits the Y endstop microswitch. This endstop has a tendency to come loose and twist, especially…
The lead screws on the original Ender NG 3 v1.2 rides on three 22 mm bearings, which sits on a 1 mm x 2 mm stop. This means that the entire weight of the bed, and all the Z motion is literally held up by a 1 mm printed stop. On my…
This is a BLTouch probe mount with thicker screw rails. The original BLTouch mount on my Ender 3 NG v1.2 cracked where the screws were mounted twice (my 68C chamber temps probably contributed), so I thought I'd thicken the screw rails to…
Want an even stronger, chonkier reinforcement? Use this model instead! In a heated chamber, the belt mounts of the toolhead base tend to pull apart and warp the model. This makes the belt loosen over time. This improved version includes a…
Here's a discard bucket with a servo-powered, twin-media brush for your Ender 3 NG v1.2! The bucket brushes are powered by a 270-degree micro servo, and a gcode macro lets you pick which brush to use (silicone or brass), and how many…
Here's a fancy set of 4020 tool heads based off the updated CFD-tuned air ducts! This model adds an Ender NG logo cutout over the fan as a fancy grill. I also fixed the stringy bridges in the lower vent by reshaping the duct (see…
This is a toolhead accessory cable mount and breakout the includes a configuration designed for using a BLTouch sensor. This is what I believe is the most common setup when converting an Ender 3 into an Ender 3 NG v1.2 (including me), but…
Here's a fan shroud for the electronics panel of your Ender 3 NG v1.2 that is built to support fan grills! To build this model, you'll need these 60 mm fan grills . Add eight M3 heat set inserts (from the Ender 3 NG v1.2 BOM), slip the…
Here's a Klicky 00, modified to fit my Ender 3 NG v1.2 with a “medium” Triangle Labs Volcano ACE hot end. Also designed to clear the Funssor CNC bed for the Ender 3 NG v1.2 , which has a bed sheet centering screw near the Klicky probe.…
This is a reinforced ProtoXtruder 2.0 designed as a bolt-on upgrade for the original ProtoXtruder 2.0! It's designed to survive the stress of high-temperature heated chambers, and is designed to jam less. Here's a list of improvements…
There's an updated, CFD-tuned set of small, medium, and large 4010 tool head fan ducts here ! Here's a fancy medium-sized 4010 tool head! This model has three improvements: Added an Ender NG logo cutout over the fan as a fancy grill Fixed…
This is a bracket for the HiLetgo 3-01-1810-5V 30A relay module that is designed to be attached to the electronics_DIN_rail_generic_mount.stl model here:…
Here's a model to mount your BTT Manta E3EZ V1.0 MCU to a DIN rail inside the Ender 3 NG v1.2! Designed to clear the 24V power supply, and leaves room for the USB and RJ45 port.
This model is a stronger idler arm for the ProtoXtruder 2.0, with a 1 mm increased gap between the idler and the extruder body! This solves two problems that I have with the original idler arm: The arm warps when heated in a heated…
This model includes three alternative lid corners for your Ender 3 NG v1.2: Blank (left corner) Blank (right corner) Blank (any corner, no cable management)
This is a mount for an Adafruit MAX31865 board, which is used to drive PT1000 and PT100 sensors with a MAX31865 over SPI. This DIN mount is styled like other DIN mounts for the Ender 3 NG v.2. Works with upstream Klipper. Here's a link to…
Use this model to mount a LattePanda Delta 3 to the electronics backpack of your Ender 3 NG v1.2 ! The standoffs on the model are tall enough to allow enough room for M.2 SSDs, and the standoffs include cutaways to ensure room for…
Pop this screen on the end of your 3/8" hose to: Siphon water out of the tank without sucking up critters Return water back to the tank without a strong stream Screen bars are 2 mm apart, so this is appropriate for neon tetras and dwarf…
This is a direct replacement for the part called “frame top rear A right top” on the Ender 3 NG v1.2, except without the filament tube holder. If you never plan to use this holder, this model helps clean up your Ender 3 NG v1.2 a little.
The CNC bed carriage for the Ender 3 NG v1.2 is a nice upgrade for the Ender 3 NG v1.2, and guarantees that your carriage won't warp if you use a chamber heater. However, the original cable strain relief does not fit on the CNC carriage.…
The Ender 3 NG v1.2 generally implies to use two power supplies: one for 24V DC (the one that is used in the Ender 3), and an additional 5V DC power supply. However, the 5V DC power supply is larger, less efficient, and more expensive…
Here's a two-piece cap for attaching a 12 mm rubber soap dispenser tube to a soap container with 38-400 threads! The cap has two pieces: a lid with vent holes to neutralize pressure, and a screw cap with ridges for grip. The the lid also…
Here is a set of planters designed to hold plants above an Aqueon 55 gallon aquarium! The clip fits perfectly snug to the profile of the Aqueon brace, and a spacer on the bottom keeps the planter level. To use a planter with a smaller…
This model helps you mount your ACS712 power sensor module to the electronics panel of your Ender 3 NG v1.2! The power sensor module sends an analog signal output that can be read by SoC modules (Raspberry Pis, LattePanda Delta 3, etc.)…
Here's a ProtoXtruder 2.0, designed as an integrated part for the Ender 3 NG v1.2! This model includes threads for a PC4-M6 fitting on top. In this model, there is a funnel-shaped hole after the PC4-M6 fitting to allow flat-cut or…
The original shroud has four screw holes. All Meanwell power supplies from the Ender 3 have two screws for this fan. This model uses two screws.
This is the same model as the original fan ducts, just without the extra heat set insert holes that aren't used for anything
This is an improved version of the Dragon ACE toolhead mount for the Ender 3 NG v1.2, originally called toolhead_hotend_dragon_ace_HF.stl . Below, the original is on the left, and this improved model is on the right. With the original…
In the Ender 3 NG v1.2, the build guide instructs the user to use the power connector and power switch from the original Ender as a donor. This works fine for on-controller firmware for a factory Ender (i.e. Marlin), but on most Ender 3…
The Ender 3 NG v1.2 generally implies to use two power supplies: one for 24V DC (the one that is used in the Ender 3), and an additional 5V DC power supply. However, the 5V DC power supply is larger, less efficient, and more expensive…
Here's a flap valve-gated, WS7040-powered CPAP blower for precise and powerful parts cooling! The WS7040 electronics are integrated right in the model, and the flap valve uses a Creality Ender 3 stepper motor that you might already have…
Here's a mount for your Logitech Brio that's designed to be mounted inside the enclosure of an Ender NG v1.2 printer! Tested to fit within millimeters of the enclosure panel, tool head, and USB C cable when positioned at an angle to…
Here is a bottle cap opener for many Amneal-branded oral medicine bottles! They open by pressing down on the cap while unscrewing them (like most caps with child protection). However, they can be difficult to open, especially if you have…
Here's a model that lets you mount your Razer Kiyo to a 10 mm x 400 mm rod between your belt tensioners! This model is designed to squeeze a Razer Kiyo inside the enclosure of an Ender 3 NG v1.2 enclosure, while leaving room for the tool…
This model is a larger cover for the Ender NG 3 v1.2 LED cable cover that allows clearance for much larger cables, like a USB 3.2 cable for a webcam. It also uses a couple M3 screws (with T nuts) to hold the cover to the aluminum…
“Wow, all these prints are making me thirsty, and my workbench is too much of a mess to hold a drink. I wish I had a hot, shaky, and borderline impractical place to put my drink with the overwhelmingly-implied side effect of impressing my…
I always thought attaching and removing a JST XH connector when handling the electronics panel cover on my Ender 3 NG v1.2 was cumbersome, and I knew in the back of my mind that the cable will probably eventually break after handling it…
This is a simple set of spice rack brackets that is designed to be attached to the back of your kitchen cabinet door. Uses a couple tap screws on either side to attach to your door. Here's the BOM! 1/4" x 12" dowel rods:…
Replace the worn-out feet on your Lenovo P50 or P51 laptop with some nice TPU replacements! The original feet has two materials: a soft exterior (that touches a surface), and a harder rubber that has some nubs that lock the foot in-place.…
The AeroPress coffee press makes a really nice cup of coffee, but after running hot water through the press, the plastic expands and the filter basket becomes hard to remove. This tool slips right on top of the basket, and offers a much…
The pogo pins used in this model are pretty aggressive on the copper tape, and will probably dig holes into the tape over time. I highly recommend building this model that uses spring test probes instead. The Ender NG v1.2 electronics…
Here's a model with a tutorial to make a nice illuminated lithophane! Head to https://tool.itslitho.com and upload your picture, then set these attributes: Shape options Attribute Value Shape Arc Width 89.1 mm Angle 60 deg Min Thick 0.7…
ExpressCard slot seeing little use on your laptop? Is your ExpressCard blank a little too boring? Store a couple of those cheap 'n crappy Micro Center drives with an SD card in there, instead! Got excited and broke your machine's…
This model is a larger cover for the Ender NG 3 v1.2 LED cable cover that allows clearance for much larger cables, like a USB 3.2 cable for a webcam. It also uses a M3 screw (with a T nut) to hold the cover to the aluminum extrusion. When…
Here is a seed catch for the Squirrel Buster Legacy bird feeder! Birds are super messy, and will happily toss a bunch of food on the ground from a feeder. Not only does this go through seed faster, but it feeds ground animals that you…
The Schlage Connect BE469ZP smart lock includes a deadbolt that supports 1-3/8" and 2-3/4" sizes. If you have a 3-7/8" deadbolt on your door, you are out of luck: this lock will not fit your door, and it's impossible to find a deadbolt…
This model helps you mount a 1/4" phono connector in the rectangular holes on the back of your Oberheim FVS-1 (four voice). These were used for accessories like the cassette machine, but realistically, these are very rarely used, and most…
I had an injury to the tendon on my big toe, and my doctor said to keep my toe raised to help encourage my tendon to heal correctly. I built this lift to live in my medical sandal, and thought I would share this here in case it helps…
These are all currently available results.
