Counting matching models…
I bought a Nikon F3 SLR camera that was missing the flash PC sync terminal cap. I modeled this one as a replacement. It is compatible with other Nikon cameras such as the F F2 F3 F4 F5 FA FG FE2 FM2 F100. I recommend printing with the…
I needed a body cap for my Sony A390 DSLR camera so I decided to make one! I tried a few other models but wanted something smaller. I also decided to add the alpha logo and a label on the inside. I've included three models: Blank Front…
A replacement motor drive cap for the Nikon F3 series of cameras. Printing recommendations: Use the lowest layer height possible so the threads are properly formed. I used a 0.12mm layer height. Print with a dark material that does not…
Replacement caps/covers for the Nikon F3 MD-4 motor drive attachment. Printing Recommendations: Use the lowest layer height possible so the threads are properly formed. I used a 0.12mm layer height. 100% infill Depending on your local…
The door handle trim on my BMW E28 broke so I created this 3D printed replacement. I know this part is still available and cheap but I wanted to practice my 3D modeling and printing skills. This is a replacement for BMW part number…
A replacement wide-down wiper for 2" Uline tape guns and dispensers. This part was modeled after the wiper found on the Uline H-150 Side Loader Tape Dispenser . The Uline replacement wipe-down part number is H-150WB .
The battery door latch for the D50 D70 D70S D80 D90 D100 cameras can break causing the door to not properly latch shut. This is a 3D printable replacement part for the latch. Print Settings and Recommendations: 0.2mm Layer Height 100%…
The Minolta SR and SRT series of cameras originally used a PX625 1.35V mercury oxide battery to operate its light meter. This battery is no longer produced because it contains mercury. A common modification to get the light meter working…
A card insert for the Nikon F3, just in case you've forgotten what camera you're using.
A replacement hood rubber mounting for many BMW models. This is a replacement for BMW part number 13411705564 . I created this part specifically for my BMW E28 535i but it is used on the E30, E36, E46, E34, E39, E24, E23, E32, E38, E53,…
A replacement hood release handle/lever for the BMW E28. This is a replacement for BMW part number 51231868556. This part was broken on my 535is which required me to use pliers to pull the hood release cable. I created this replacement.…
A replacement hood rubber mounting for many BMW models. This is a replacement for BMW part number 64111369828 . I created this part for my BMW E28 but it is also used on the BMW E24 6 series. Recommended Print Settings: TPU 0.2mm Layer…
A replacement intake boot for the BMW E12 E28 E24 E23 and 2500 series cars using the M30 series of engines. This is a replacement for BMW part number 13711261370. I printed this part out of Bambu TPU 95A and installed it on 9/5/2026. I…
While working on my 535is I needed the vent hose that connects from the valve cover to the intake boot. I had ordered the part but it hadn't arrived yet and I wanted to start the car to troubleshoot some other issues. I created this model…
This replaces the obsolete 1.35V mercury batteries with either one 3V CR-1/3N or two 1.5V LR44 or SR44 batteries. Note: This camera's meter was designed to run off two 1.35V batteries (2.7V in series). Using one 3V or two 1.5V batteries…
This is a remix of Kirils Deep 55mm lens cap . The only thing I've done is scale the model by 89% so that it fits lenses that use 49mm diameter caps. I printed mine out of ASA with a 0.1mm layer height.
A replacement hood rubber mounting for many BMW models. This is a replacement for BMW part number 35411152744. I created this part specifically for my BMW E28 535i with the M30B34 engine. This grommet is designed for the an accelerator…
This is a replacement bushing/spacer for the E28 speedometer module. Speedometer part number is 62121377617. The bushing has an ID of 6mm, OD of 9mm, and a height of 4mm. Print out of TPU.
My HP Photosmart M737 camera's battery door broke so I designed a 3D-printable replacement. Recommended Print Settings: ASA or heat resistant material 0.1mm Layer Height 4 walls 100% Infill No Supports Installation Instructions: Bend up…
My HP Photosmart M737 camera's wrist strap eyelet broke so I designed a 3D-printable replacement. You'll need some longer screws to fit this replacement. I used 5mm long plastic screws. Recommended Print Settings: ASA or heat resistant…
These are all currently available results.
