Counting matching models…
Adjustable Twist lock cam system for generic Aluminium tube. Multiple uses but tent pole is basic use case. Built as commercial twist lock tent poles were a rip off. Could buy two diameter 6.5m lengths of tube and a roll of filament for…
I started windsurfing with a Powerbox board so accumulated Powerbox fins. Then as progressed switched to tuttle boards. Wanted to convert my Powerbox fins to tuttle but keep the ability to use them as Powerbox so can still use my Powerbox…
Sail Rocket 2 set the current water speed record for wind powered craft in 2012 of 68.33kts peak and 65.45kts over 500m. Paul Larsen was inspired by the design of Bernard Smith in 1963 to build a sailing craft like an aeroplane that…
Highish powered food/anything syringe for a 600ml PET bottle. Designed this to replace the feeble icing bags that aren't strong enough to force stuff like mashed potato through small opening. This was my first multi component build and…
Simple building block to make it easier to build awesome natural landscapes for Aquariums, Terrariums, Greenwall features or Microgreens. Anyone doing any of the above knows it's not trivial trying to sculpt landscapes with living plants…
Simple pipe benders for short radius bends up to 90 deg. Print at high or 100% infill. Radius is marked on the blocks. Hold in vice firmly ensuring 10mm straight section is fully in the jaws of vice as shown and bend away. Worked with…
I have the Multisharp drill bit sharpener which works great but seem to have misplaced the large collet to suit the bigger drill sizes (8-13mm). Didn't want to spend the $50 to get a new sharpener so printed this. Seems like the original…
I needed some end plugs for standard black 13mm poly pipe. The local hardware store wanted $0.49ea plus they had no stock so quickly made these. Work great. Print in PLA or PETG at 10% infill. Two versions, one just the end plug, one with…
This is basic “gun” to force stuff out a various shaped nozzle. Meant to replace an icing bag that can't handle much pressure. You can use it for food (potato/any kind of similar food, playdough, cement, mud, plaster. Was fiddling with…
Adapter to convert a Powerbox fin into Deep Tuttle. Note: In addition to the holes you need to drill, you also need to sand the Powerbox front and rear slightly. This is because Powerbox length at the board interface is 160mm but the…
This is simple attachment that fits on standard painting pole to push and pull stuff that is out of hands reach. i.e. opening/closing high windows, picking fruit out of reach, grabbing stuff from deep in a cupboard. Wifey had used it…
Outhaul pulley for windsurfing. Keep them on your sail in each clew position for fast rig and on water changes. Cost is about 50 cents unlike commercial versions costing $30+ There are two designs to accomodate different pulley tube…
These drill guides are used to drill the holes in a Powerbox fin in order to convert it to Tuttle or universal. They are meant to help when using this adapter. https://www.printables.com/model/491976-powerbox-to-tuttleuniversal-converter…
If you use Aquaponics to grow stuff like Micro greens, the nutrient rich water contains lots of solids (Fish poo). This can be despite many levels of previous filtering. Plants of any kind can't consume these solids, so these naturally…
Updated and strengthened design here https://www.printables.com/model/155753-ryobi-extruder A Ryobi silicon gun in its intended use is very handy for running a continuous neat bead of silicon around a bath etc. A further enhancement of…
Different way of making a 3D printed windsurf fin that can withstand the extreme forces. This is not meant as a new revolutionary fin but a new way to 3D print windsurf fins quickly and cheaply to try out new ideas. The whole idea is to…
I hand drilled my own bore and works great but the flow rate is very low (6 litres per min at best). This accumulated into a large tank which then feeds the house, reticulation etc. Since the flow rate is very low and the consumption is…
Rear facing shots at water level whilst windsurfing give awesome shots both of the high speed wake and your mates chasing you. This simple mount connects to the rear tuttle bolt. A piece of 3mm x 10mm Aluminium bar is the reinforcement…
Whilst making and waiting for the pots to print on my previous building block design, it occurred to me it would be way faster and cheaper just to make a clip to hold the 50mm pots together that aquarium plants typically come in. The…
Since a pile of people seem to be making these I thought I'd update the design based on lessons learnt. This is to house Jan Heynen's design DIY GPS (links at bottom) Note, this is NOT waterproof, it relies on filling the case with…
I wanted to try some thrusters out on my free ride board but didn't want to spend the $40 to buy a set so printed my own for way less. Cut the main shape out of 1.5mm stainless, ground the trailing and leading edge and contact cemented it…
Couldn't justify paying $100+ for one of these things so quickly made my own. Made for 10mm pipe. I used 10mm plastic coated steel tube which I had lying around which had OD of 10.2mm and 1.5mm wall thickness. I printed at 100% infill for…
So annoying when you are at a party/function with a drink and lots of nice nibbles but always a struggle to hold a glass with nibbles. Either you have to put drink down or just grab one mouthful of nibbles. If a busy party you may loose…
Gives drone like shots without the drone for those that want footage of their vehicle racing 4WD driving etc. The original mount using 8mm carbon square had some vibration when coming out of corners so changed design to suit 12mm carbon…
I needed a very low profile rack system for my gear as wind variation here extreme so need to pack lots in. Also needed to be able to quickly adjust the racks to suit various gear and also remove the whole rack system quickly in order to…
A shoulder or helmet case for Jan Heynen's DIY GPS. Links to detailed instructions and the main discussion thread on how to build the electronics part at end of this description. Note, this is NOT waterproof as is, it relies on filling…
This is a boom mount to suit Jan Heynen's DIY GPS that integrates the elastic so you don't have to have the elastic stay on the boom. It eliminates the two side tabs that appeared to some users to break. Having no tabs means you can move…
I needed a timer system to turn my Christmas lights on/off at various timings to achieve various effects. There were 12V motors, 12V LEDs, 5V Arduino's and LED strips and also store bought waterfall lights that needed to be controlled. I…
This is V2 of experimental fin. Video here (V1 was essentially the same design but had the tuttle bolts welded to the steel plate but the welds failed on first test, unfortunately no video) Annular fins in theory should offer more lift…
2 Pole Slip ring that can withstand vibration. I initially made a slip ring system that used 18mmx12mmx4mm bearings with the electrical contacts just wires that the bearings press fit on and screws making contact with the outer race. This…
This is similar to previous weed fin but instead of the airfoil increasing around the diameter this fin decreases chord length. Also add bulbs on tips to reduce tip turbulence. Annular fins generate more lift for less draft so in theory…
This is a modification to my original print that can be found here https://www.prusaprinters.org/prints/104363-windsurfing-speedo-doppler-gps-low-profile-counter This print adds a trim layer that makes the unit more professional looking…
Uploading V4 of the experimental annular fin to show design evolution. This concept introduces the transfer plate to transfer the load from the tuttle bolts to the fin. This is hidden inside the tuttle connector. Again fin failed quickly…
Shoulder mount case for T-Display DIY GPS. End unit is about 3 times smaller than the Epaper version. Instructions how to make the electronic side at https://github.com/RP6conrad/T_display/blob/main/README.md?utm_source=seabreeze.com.au…
I made 2 versions of the Modular Fiddle 4 String V4. My wife a professional Violinist said the sound was quite reasonable. I was surprised no 3D printed case existed for either this Fiddle or a normal Violin so quickly hacked the…
Previous uploaded helmet mount relied on the tiny display piece of plastic that comes with the GoPro 360 (labelled “remove”) to stop the mount tilting. Worked great until this tiny piece broke. This print is complete overkill to eliminate…
Small variation from previous shoulder/arm case for Jan Heynen's DIY GPS which has trim inside polycarbonate face. Whilst less likely to get damaged compared to boom mount there is potential for the thin trim mounted outside the…
Most think it's not possible to 3D print a windsurf fin due to the extreme loads. However, 3D prints are almost indestructible if held in compression so uploading a few windsurf fin designs that show how to print a fin that can withstand…
This is a replacement for the fancy Severne RDM extension widget to adjust the extension height. While the Severne collar is fancy, if the rubber band breaks (very easy on rig down), the collar just falls off and gets lost. Easy to do and…
Annular fins in theory should generate more lift in light wind conditions for less draft than a conventional fin (think of it as a low draft formula fin). Higher aspect ratio fin like this should in theory have less drag. Uploading this…
After playing around with the basic downhaul winch design it was apparent it could be improved. The main improvement is the basic design could fail under high loads due to the torque applied tending to separate layers of print so added 4…
The Kitchenaid Pasta roller attachment is useful but after time is gets dirty and the temptation is to put a rag or other object in to clean the rollers whilst its running. This can lead to a jam and to stop the main machine self…
This is mast mount for Jan Heynen's DIY GPS. https://www.seabreeze.com.au/forums/Windsurfing/Gps/Another-DIY-GPS-logger-approach?page=1 Not my idea (Boz's) and (Al Hop's integrated elastic strap) but aims to put display more in peripheral…
Uploading design just to show evolution of the annular fin concept. Whilst I filmed the test with the fin cam I haven't got around to uploading the video of the test. Suffice to say, it worked like V2 but it did not last long. Need to add…
With Windsurfing records now exceeding 100Km/hr there is a real need for an accurate feedback for sailors. All previous systems have relied on a watch screen (impossible too see at high speed) or some sort of audible feedback. Most are…
I wanted to construct experimental setup using pressure pipe but be able to change/dismantle it as required. Gluing the various fittings together is quite expensive and if you need to make a small change you have to either throw it away…
Useful couplings to construct a variety of light weight frames using 1" (25.4mm) square Aluminium extrusion. You can buy these at a hardware store, except when you can't. There are also shapes you can't buy. These parts are hammer fit and…
This little window robot has worked flawlessly for years. Suddenly the drive started making ‘clicking’ sound and the robot could not climb, just go down. Traced the fault to the main drive gear entering the planetary gear had worn. Could…
Trying to get underwater footage of windsurf fins to understand them better and get different action shots. This one is non destructive for the board for GoPro 9,10,11 and relies on a small piece of clear poly carb matched exactly to the…
I needed a slip ring quickly but could not find anything so came up with this. It uses 18mm x 12mm x 4mm bearings, 8mm threaded bar and 3mm nuts and bolts. You need to cut two grooves in the 8mm threaded bar to suit whatever wire you are…
I made the Modular Fiddle 4 String V4 with MQTT controllable LED Lights and wanted a matching bow. This fits a WemosD1 Mini and a 500mAHr battery. The battery lasts about 1hr using the Rainbow effect at brightness 128 (1/2 power which is…
This fin cam relies on cutting a hole in your board…here where I live people seem to throw out perfectly good boards so scored a few donor boards to try this out. Scored a near perfect 2006 iSonic 111 just a few meters from my house…how…
I made the modular Fiddle 4 String V4 but was surprised not a single Violin case was available for it or a standard Violin. My wife (Professional Violinist) said the Fiddle produced quite a decent sound and she needed to travel with it.…
This version corrects a few minor errors in previous prints with also option for Al Hop's suggestion to centre the screen. Note to centre the screen you need to carefully put a knife between the display and PCB beneath. I managed to crack…
Have a couple of race mates (one thankfully with an EV and the other powered by dinosaur juice) that keep asking me to fly the drone and follow them whilst racing. There is a much easier way and that is with a 360 camera to get a similar…
Animated Christmas Crab light. The Silhouette I used is attached but generated from a silhouette and fed through https://rasterbator.net to desired size. Print out, trace onto 3mm MDF, paint in a metallic paint (aluminium used here). The…
A Christmas lights fire fighting Helicopter. It features a few prints that are described in detail as per links below. A simple MDF cutout is spray painted, some LED strips placed around outline. The various components could be adapted to…
These are all currently available results.
