Counting matching models…
A compact attachment that screws onto a Dremel flexi shaft for cutting 5mm rod or tube. Use with a 38mm grinding disc or saw (saw not tested). I use it to cut carbon fibre tube. The two parts print in place without additional support.…
A simple, easy to print holder for an endoscope/borescope. Will accommodate 7.5mm diameter camera, should work ok with smaller ones (eg, 5.5mm) too thanks to clamping screw. Retains the camera position geometry from the original, but…
Note: You will also need to download this sizing guide . Design Intent On the bottom face of the tube, the metal-to-metal clamping stack in the stock design is maintained without adding a layer of printed part in between the nut and the…
Background This model is based on this forum discussion , notably the ideas and experiments of forum user @kaaaaaaaaaaaaal. But while @kaaaaaaaaaaaaal drilled holes into the stock parts, this model is modified with the required openings…
Designed for 20mm x 20mm box section tube often used for the x-axis gantry beam on corexy printers. Some tubes have relatively wide dimensional tolerances due, for example titanium tube might be 20mm +/- 0.3 mm - so anywhere from 19.7 to…
Modified parts for the VC4 to suit enclosure panels other than 4mm thick.
This is for 50mm inner diameter spiral hose (aka convoluted hose, or flexible ducting hose), the kind typically used in a workshop for dust extraction (although often it's larger diameter in a workshop). I find that for short runs, 50mm…
Sandwich the lengths of belt together, teeth facing each other. Use the marks on top as a visual guide/reminder to decide which length of belt has the leading tooth - this is important when deciding where to cut if you need exact matching…
NB: The photos are posed with a benchy from a different printer, my VC4 build is not complete yet. Printing Follow the standard RatRig printing guidelines here , and the part preparation instructions in the build guide here . BOM 4 x…
Common placeable components are here , find other placeable components in this collection , or search for tag bumbagcomponent . NOTE: The base enclosure is only compatible with the VC4 BOM V1 electronics enclosure (the version that has…
To have all top surfaces of the model be at their intended height, you must either use 0.1mm layers everywhere (except 1st layer), or you can use 0.3mm layers with thin layers only where needed to get the correct top layer heights. Using…
Designed from scratch to be a bit more slender and sleek than some other designs which are great but look a little over-chunky for my personal taste - but you may prefer them, so do have a look:…
Print with 0.2 or 0.25 layers, typically ABS or ASA for RatRig users. Use a small zip tie to hold the thermistor in position. The glass bead should be held flush to the surface or slightly below, so it gets good exposure to air, but is…
A collection of common utility placeable components for the Bumbag Customizable Enclosure System including cable management, mounting posts, screw-from-underneath cutouts, vents and fans. cut_under_m3cs Creates a countersunk cut-out for…
Either modify an existing printed part, or print this model with standard RatRig printed part settings and recommended materials. It's really easy to modify an existing part and likely has negligible structural impact. Modifying an…
Design This is what I call a “nutty spanner” - a hexagonal pattern of M3 nuts is used to provide a tough surface against which the target M3 nut can be torqued. This is longer-lasting than a simple printed spanner (at least with common…
Simple remix of the knob which adds a flat side which can sit on the printbed so no support is required. See the original model for other parts and details.
Under Development! This model is awaiting actual use testing - I've tested integrating the model with the IEC sockets, but I'm waiting for a VC4 to test the fit with the electronics enclosure. Feedback welcome. Updates are detailed below…
The main riser parts attach to the top of the existing lid and provide a surface for the four rubber feet of another unit to sit on top. You need two riser parts per lid. The existing screws from the Polyphemus lid are reused. There are…
A placeable component for the Bumbag Customizable Enclosure System . Product page here . This model incorporates a modified version of the SKSM 3D model published by Schurter. Sellers: RS Components
See this discord message in the toro discord for usage, and to discuss/troubleshoot. Printing Use something tough like PETG. Plenty of perimeters (at least 4 or 5). Thicker layers are better for strength, but you may loose accuracy on the…
UPDATE: Do not use this mod or any mod that keeps the second carriage in place, it will severely impact tuning belts and input shaper. The second carriage must be removed. For reference, see this discord post from the author of RatOS.
A placeable component for the Bumbag Customizable Enclosure System . Find the product here . This model incorporates a modified version of the 3D model published by BIGTREETECH here .
Follow the printing instructions from the original model, especially the seam enforcer. For other sizes you'll need to use Fusion to play with parameters and export STEP or STL.
In combination with some common plumbing parts, this print allows you to connect your EasyGreen EGL sprouter to your mains water supply so that you don't have to top up the water reservoir by hand. Great for general ease of use, essential…
Log cabin style construction is often used for garden buildings and outbuildings such as a garden office, studio or summer room. The walls are built from stacked lengths of timber which contract and expand according to temperature and…
While some kiwi varieties are self-pollinating, many are not. The female plant produces fruit, but only if the flowers are pollinated with pollen from a male plant. If you only have a female plant (or it's not close to a male plant), but…
These are all currently available results.
