Counting matching models…
As if there weren't already enough Scrub Daddy sponge models out there, my wife didn't like any of them. She wanted a simple design that would sit on the counter behind the sink - not in the sink, or over the sink. But one that wouldn't…
I wanted a holder that would hold TWO bits on my DeWalt impact driver and drill, and found some good options on Thingiverse and here, but the ones I found used a friction fit to hold the bits, and I found that I was occasionally losing…
I built this to change from 4" corrugated drain pipe to 3" pipe. Normally you want to go the other way around, but in my case, I had reasons to want to run 3" pipe, and since the pipe is fed by a 3"x2" downspout, I figure there's no…
This is a 90 degree, long sweep elbow for 3" corrugated drain pipe such as can be found at Home Depot or Lowes. They sell drain pipe elbows there as well, but they seem to have female ends on both ends, rather than a male and female, so…
This is a Y fitting that allows joining 3" corrugated drain pipe into a 4" pipe. You'll have to excuse the main photo - I had a design problem when printing (2 components of the design were not fully connected to each other). The attached…
My wife wanted me to make a handle extension for her Swiffer Duster - something that would let her reach some windows in our stairway. In the old days, I would have just duct taped the Swiffer to a pole, but what fun is that? Choosing a…
I bought a set of bird spikes on Amazon and ended up with way more spikes than I had bases to put the spikes in (a picture of one of the original bases, made of metal, is in my first photo). Rather than buy another set of spikes/bases, I…
There are lots of filter baskets out there, many of them fit hose ends, but most of them seem designed to strain debris from going into a hose. My purpose is to catch debris as it's leaving the hose. My specific case is that sometimes I…
Background on why I did this: We have taken a few cruises and noticed that people often bring their own travel mugs, because the to-go cups they have onboard are paper with a cardboard wrap, and ill-fitting lid. But to bring your own…
First, I cannot thank steriku enough for putting this out there - with my limited tools (Tinkercad), I really would not have been able to do this. My camper lost it's downspout, and I wanted to replace it with something better - and this…
Most of the downspout filters I've seen other people post seem to work on leaves, not fir needles. We live in an area filled with fir trees, and in the wind, they blow off the trees and on my deck. Then when it rains, they fall between my…
This is a remix designed especially for mudpuddles. I believe that the original was made for water in a pool cover (generally clean water), but I wanted something to suck the water out of holes dug in the ground that have filled with…
I built this for an Echo Dot (Gen 4) that we have on our deck outside. The device is under the eves, so it won't get wet, but I also didn't want pollen and dust, or spiders, or other bugs, all over it - especially in the winter when we…
We built a decorative concrete block wall (Home Depot 4"x9"x8" deep blocks) a decade ago, but had to reroute a gutter downspout drain line recently. This required burying a new line of corrugated drain pipe, but we wanted to terminate the…
This is a travel guard that snaps over the trimmer's on/off button. The trimmer is really great, except when it turns on in your luggage and causes TSA to get all excited. Actually, that's never happened to me, but I have had it turn on…
This is a stop that wedges into a rope to prevent a pully wheel from going any further. I built it to stop a small pully that connects to a pet leash, so that our cat (would work just as well for a dog) can roam freely in the campsite…
We got a set of Enbrighten Vibe Eternity LED lights that are intended to go on your eves, and shine against the house for accent. The problem is, we used them on an awning support frame, so they don't shine right next to the house, and…
This is a simple sign, made to be as wide as my print bed allowed, that makes it clear that we don't want people coming to our door uninvited. The screw pattern is intended to be used on a 2x4 or 4x4, and sticks out like a flag. I printed…
The bevel adjustment lever on the back of my Ryobi miter saw came apart - must be age related, since I'm slowly falling apart as well. This is a replacement that (so far) seems to work well. You need to reuse all the metal parts, and…
Most of the shower head holders I found screw to the wall or to a pole that is mounted to the wall - essentially, they are all for long-term use in a shower. I had shoulder surgery and only need to temporarily change the shower head…
I wanted a thermometer for my RV that had 3 external sensors (one for outside, one for the plumbing compartment, to make sure it's not freezing, and one for my battery compartment, to make sure my lithium batteries are not too cold to…
These are all currently available results.
