Counting matching models…
Quick and dirty remix of the very well designed corner clamp from jtronics on thingiverse: https://www.thingiverse.com/thing:4666879 Just merging the guide of the central part with the 90° adapter b part. Improves the rigidity to the…
Remix from this design on thingiverse : https://www.thingiverse.com/thing:4569034 I started this remix because I had quite many broken carpenter meters at hand (like many of you I suppose). Minor adaptations of the initial design: adapted…
Easy to print Gardena compatible multi-connector with good water sealing. The connectors are fitting tightly but are easy to connect/disconnect. I only printed the 6 connectors version for a project. The 4 connectors version is provided…
Very basic remix of Dodoka's model, 90% of the work was already done. Fits a x6 cups Bialetti moka with 65mm (outer) diameter coffee container. Scaling the part for other sizes of pots should just work: measure your coffee container,…
Remix of the SSSStorage from Henkheld: add top and bottom parts to make the design stackable replace plastic hinges with crossing metallic hinges hinges are also acting as feet and main assembly part separate nuts for overall assembly:…
Needed hardware x2 608 bearings (22mm ext-diameter, 8mm int-diameter, 7mm thick) x6 M3x12 screws x6 M3 threaded inserts x1 M5 threaded insert (optional) x1 (or x2) PC4-M5 quick couplers for 4mm PTFE tube (optional) PTFE tube x1…
Fits Cosmo/Kermi flat radiators with 10mm grid spacing. Freecad parametric model file provided for adaptations to your specific radiator model (likely to be needed depending on the grid spacing, shape, width…) Needed hardware: x1 25mm rod…
Frame: TBS source 1 v5 5 inch Battery: Tattu v4.0 1050mAh 130C dimensions: 78 * 40 * 34 mm It is unlikely that this part will fit perfectly your setup but you can adjust the provided FreeCAD parametric file to your frame and battery.…
I was looking for a reliable finger strapping solution to practice Judo. Objective being to prevent lateral movements of the finger (e.g. in case of strain) while still being able to properly grab, grip and eventually throw opponents. The…
Good point, it fits perfectly this particular model of shifter. Bad point, it will probably not fit any other. Printed with poly-carbonate filament (Prusa PC blend). 100% infill / 0.2mm layers / 5 perimeters / no support
Used with - TBS source 1 v5 5-inch frame - 30mmx30mm stack Adaptations might be needed to fit your setup; the parametric FreeCAD file is provided accordingly. Printed with TPU, 0.2mm layer height and 100% infill
The boxes slide and can be removed easily. Uncomplicated print. PETG, 25% infill, 0.2mm layer height.
Required Hardware: a pair of specific hinges such as: https://www.amazon.de/-/en/Rev-Shelf-LD-0220-50SC-Close-Hinges/dp/B018A36II6 6mm thick board for the back and bottom of the tray There are 2 different sizes: the small one: 15cm tall /…
PETG 0.2mm layer height 20% infill supports needed (see picture)
The original small plastic feet broke. I modeled and printed a couple of replacement ones; let's see how long they will last. The 2 strip holders have to be pushed in place using a manual press or a vice. They fit very tightly (this is…
Remark on the belt dimension After mounting the belt you must have a very tight fit on the pulley otherwise the motor will skip teeth under load (guess how I know that). With my robot, I ended up switching from the original 49 teeth belt,…
Remix from the following parts available on thingiverse: https://www.thingiverse.com/thing:21724 https://www.thingiverse.com/thing:2090975 Needed hardware: Magnets: diameter: 10mm height: 5mm Metallic rods: diameter: 4mm cut to desired…
My requirements: simple workflow to load/unload filament possibility to manually push/pull the filaments to fix failed loads/unloads (yes it happens) weights guided during printing (and always tidy and at hand when unused) weights can be…
Rationale Those replacement rollers are slightly raising the front of the robot and lowering its back so that the main brush gets less friction on the floor. This prevents the brush from getting blocked and the belt to skip steps (can be…
Assembly Print x6 new flaps upright Pull out the x2 green end caps of the brush Slide the x6 old flaps out Slides the new in place Push the caps back in place (paying attention to the correct orientation: there is a small notch) Print…
These are all currently available results.
