Counting matching models…
This model allows you to mount the M18 batteries for the Milwaukee tool system on or under a shelf, or on a wall. The batteries snap in using the same retention mechanism as they do on the tool. This lets you mount them where it's…
I was building my own drybox and needed a port/pass-through to route filament out of the box. I wanted something that would utilize a PTFE tube and a fitting to hold that in place. I also wanted to be able to seal it off when not in use,…
I wanted a way to secure some cables on the DIN rails in my V-Core3. I liked the DIN rail cable organizer by Farnsworth, but I preferred to use the newer version of the Voron DIN rail clip. So I remixed (recreated from scratch - no CAD…
I have a drybox that uses PTFE tube to route the filament to my printer. When not in use, I needed a way to cap the PTFE tube to keep moisture from getting into the box. I also wanted something that would grab hold of the filament so that…
Case for Small RP2040 Boards This is a case for the small RP2040 boards such as the Adafruit QT PY RP2040 or the Seeed XIAO RP2040. These small boards based on the Raspberry Pi RP2040 microcontroller. They have a USB interface and are…
This is a jig used to cut 9mm pieces of silicone tube for use with the Silicone Tube bed leveling mod for Prusa MK3 printers. The mod is described very well here: https://github.com/bbbenji/PMSBLM and here:…
These clips allow you to use a zip-tie to secure a cable/wires to a 3030 aluminum extrusion. To use them, insert into the slot in the extrusion and twist ninety degrees. Then insert a zip tie through the slot in the clip and secure your…
My wife had a ratty old cardboard container holding her Q-tips, so I made her this one as a replacement. There are three parts. The handle screws into the lid and was designed as a separate part for ease of printing. Note: photo shows an…
Many printers, especially those with a Bowden extruder, use PC4-M10 fittings to retain the PTFE tube at the extruder. Reportedly on Bowden printers it helps with retraction if the fittings at both ends have a firm grip on the PTFE tube so…
User Jevermeister designed a nice DIN rail mount for the Tobsun DC-DC converter modules. However, his design was made to be used with the older version of the Voron DIN rail clips. I wanted a version to use with the newer clips. While I…
Magnetic Mount for ADXL345 Accelerometer This design is a detachable mount for an ADXL345 accelerometer to be used with Klipper 3D printer software for measuring resonance for its Resonance Compensation (aka Input Shaper) feature. The…
This is a jig that compensates for the blade kerf when performing waste side cuts with a track saw. You insert it between the you're measuring device and the rubber blade guard on the track. This is not my idea, but this is my design. I…
These are 3D printable equivalents of the mounting plates used with Temple Audio's pedalboard. Using some mounting tape, you attach one (or more) of these to a guitar pedal. The mounting plate alignment nubs and center screw go through…
My CNC machine has a dust boot on it that attaches to arms on the gantry via a magnetically coupled brackets. I broke both the dust boot and one of the magnetic brackets when I inadvertently clipped a clamp. I was able to order a…
The Clicky-Clack Fridge Door Mod for Voron 2.4 and Trident printers is one of the best mods you can do to your Voron printer. The mod uses some rubber strip (aka “panel clamps”) that sits between the extrusion and the acrylic panel. To…
This is a set of printable nut drivers for nut sizes that are common when working with guitars and guitar effects. This includes: 7, 8, 10, 11, 12, 14, and 15mm, as well as 1/2, 3/8, and 7/16 inch. Because they are plastic, it minimizes…
I like the snap-in switched outlets like those used in Voron printers. I wanted something similar for my RatRig VCore-3 build, but I didn't find anything. So I modified the Voron power inlet to allow mounting to two 3030 extrusions. This…
On my Prusa MK3, I use the excellent Bear Extruder and X-Axis (see link below). This project comes with a nice jig you can use to chamfer and cut the PTFE tube. However, the PTFE tube when using the standard E3D-V6 hotend is a different…
This is a tool to allow you to keep your hands away from the blade when you are cutting small pieces on a miter saw. I saw a wooden version of this on the DIYForKnuckleheads Youtube channel (…
I am a big fan of the Bear upgrade for the Prusa i3 printers (See details here: https://github.com/gregsaun/prusa\_i3\_bear\_upgrade ). When i was assembling the upgrade, I found it quite tedious to get the Y idler and Y motor…
I am a huge fan of the wonderful Bear upgrade to the Prusa MK3/MK2 printers from user pekcitron ( https://www.thingiverse.com/thing:2808408 ). I recently built an enclosure to house my Full Bear MK3 and wanted some additional cable clips…
This is a small clip that holds the bowden tube to the extruder wire bundle and optionally to a 3rd wire, for example that attached to a bed leveling sensor. It lets you remove the tape that is used on some printers, proviinge an overall…
I have created several versions of this case. This evening I realized that somehow this one didn't make it over from Thingiverse. This is the version of the case that I use and that I prefer. I am using it on a Prusa MK3 that has had the…
IKEA BROR Shelf Support Cable Clips These small clips allow you to attach cable/zip ties to the side and center support brackets on an IKEA BROR shelving unit.They are very useful for securing wires that you want to run along under the…
NOTE: This is an update to my [original rear plug PSU design] ( https://www.thingiverse.com/thing:3180564 ) Although the original design was functional and served it's purpose, several users reported that it tends to warp during print.…
ADXL345 Mount for Bear Extruder A mount that allows you to attach an ADXL345 accelerometer to the Bear Extruder for calibrating Klipper's Resonance Compensation (aka Input Shaper). This mount works with many of the commonly available…
Raises Logitech Webcams like the C920 up slightly to accommodate the thin bezzle of some Dell monitors. It is specifically designed to work with the Dell U3219Q, which is thicker than some of the other Dell monitors. I got the idea from…
A small stand for various safety razors. I have included versions for the Feather AS-D2 and the Above-the-Tie Atlas. However, CAD source is provided and is fully parameterized, so if you know how to use Fusion 360, you can customize this…
I recently assembled a V-Core3 printer from a RatRig kit. I put together the attached tools to assist with assembly. The tools are: Spacers for the A and B motor pulleys. You snap these on the shaft, and then put the pulley on and slide…
I like to use the Plano 3600 and 3700 containers to store small parts like screws and electronic components. The dividers in these tend to come out, causing the components to mix together. So I created these trays that drop into the Plano…
I wanted to use a Mean Well LRS-350 power supply with my Bear upgraded MK3, so I designed the case available here: https://www.thingiverse.com/thing:3111868 Some people asked about a version with the plug coming out the rear of the case,…
I like the snap-in switched outlets like those used in Voron printers. I wanted something similar for my RatRig VCore-3 build, but I didn't find anything. So I modified the Voron power inlet to allow mounting to two 3030 extrusions. This…
I have a set of Powerblock dumbells that I store on one of the Powerblock Compact Stand. This stand has 4 circular cutouts to hold the 2.5 pound cylindrical weights that are normally held within the Powerblock dumbells. I wasn't happy…
I love the little $20 cameras from Wyze ( https://www.wyzecam.com/ ), but the magnetic mount they come with is limiting. This design allows you to securely mount a Wyze Cam v2 to a tube. It's designed for a one inch tube, but Fusion 360…
If you have an Voron Trident or 2.4 printer built from one of the LDO kits, your heatbed most likely has 4 slots in it - two in front and two in back - which also contain an unthreaded M3 sized hole. This design allows you to utilize…
This design provides a holder for a brush that you can use to automate cleaning ooze off the printer's nozzle. The design works with the Salad Fork printer (mini Trident). It is designed to hold the silicone nozzle wiper that Bambu Labs…
I purchased a Mission Engineering SP-1-ND expression pedal. When I went to go mount it on my pedalboard, I discovered that an additional accessory was needed to do this. Not wanting to wait another week for this to arrive, I designed my…
Customized version of https://www.thingiverse.com/thing:2124509 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing\_id=2124509 Instructions Using the following options: boxWidth = 192 boxDepth = 87 boxHeight =…
I love the little $20 cameras from Wyze ( https://www.wyzecam.com/ ), but the magnetic mount they come with is limiting. This design allows you to securely mount a Wyze Cam v2 to V-Slot extrusions that are commonly used for 3D printer…
I purchased the little mechanical computer toy/game called "Turing Tumble" ( https://www.turingtumble.com ). It is a really cool toy, but the board for ours was warped enough so that the plastic pieces that connect the marble release to…
I've been using Adafruit's wonderful Heat Set Insert Rig with a Haako soldering iron for years. I wanted to adapt it to use the Pinecil soldering iron to make a more compact assembly that would be easier to put up and take down off the…
The Bear upgrade for the Prusa MK3 is a wonderful bit of work ( https://www.thingiverse.com/thing:2808408 ). It now comes with some nice reverse Bowden adapters that attach to the Bear's v-slot frame. These adapters work great with the…
I recently built an enclosure for my Prusa MK3 and wanted a way to secure the LCD to the outside of the enclosure. The attached LCD supports will allow you to secure the LCD/controller with a screw. Note that these are remixes of the…
SQ-ES126 and Wiha Go Box MicroBits Stand A stand for a Sequre ES126 electric screwdriver and the Wiha Go Box MicroBits Set. Description I have one of the ES126 small electric screwdrivers from Sequre. This model has more torque than the…
This is a holder for these excellent drill bits: Star M Japanese F-Style Anti-Burr Drill Bits with Hex Shank The magnets I used are these: 5x5mm rare earth magnets I printed it in HTPLA, however, it should print fine with any material. No…
I have a SensorPush temperature/humidity/barometric-pressure sensor that I have mounted on my front porch. I initially used a design where the sensor just snapped in, but I got concerned that someone could easily steal it. So I designed…
These are all currently available results.
