Counting matching models…
Simple cabinet door and drawer handles with 2-sided tape mount for 18mm thick panels (3 size variations). Made for temporary use until I decide what will be the permanent “style” - although they are tougher than I initially thought. Only…
Simple holder for pan and lids to keep 'em organized. Just print 2 of sides for pans or lids and print the needed amount of connector pieces. Clicks together easily. I printed mine with PLA.
Drill guide for Forest HB-204 hinges Dimensions on the picture, might be good for other types as well.
Simple squares to hold 18mm furniture boards square while screwing. Snug fit. The jig itself can't be clamped, for glue-works can't be used on its own.
Enclosure/electrical box for common cheap-o solar charge controller. The box fits the controller, place for optional 4010 fan(s) (on both sides) and 3 inlets for wires (fit for 20mm diameter wire hose). Box has ventilation holes on both…
Chain guard for 26" MTB with 4 mounting holes Dia. 188mm, mounting holes circle dia. 144mm. The 4 holes are not placed in equal distances, see the exact dimensions on the attached picture (Not a F360 pro, but fits and works). For 4.0x10…
Bathroom/kitchen organizer: - soap/sponge/rubber duck holder with drip chute - toothbrush/razor/brush/toothpaste holder - space for shampoo/dishwasher - … The prototype was printed in PLA: ~110g filament, ~4+h print time, minimal amount…
Headphone holder with place for jabra evolve30's control thingy. (Model w/o the plate attached too.) Holder's inner diameter is 55mm. For table thickness 9-29mm. Printed with Anycubic mega My used print directions are on the attached…
Replacement stem for drain plug compatible with Teka sink. Might be good for other models too - check the main dimensions on the attached picture. Printed with - PETG - 100% infill - best print direction on side - hole placed…
3x 5mm pin hole in 50mm spacing. Requires center drill and try-square. Center drill outer diameter 8mm - drill bit 5mm. Try-square's plate dimensions 24.8x2mm For assembly 6xM3 nuts and bolts + 2xM3 nut and bolt for plate fixing Printed…
Just another screw knob for M8 screw with matching contra nut. Overall diameter 31mm Once screw inserted, the cover can be glued - using glue to fill the empty space advised so water can't collect and corrode the screw base. I use them as…
Four-leaf clover for good luck Original is roughly 16x17cm - scale as you like.
Camar/Forest 801 cabinet hanger covers modified to be longer and with wider skirt. I printed mine with PLA, standing on the skirt using tree support. Step file attached so everyone can tailor for own needs.
Sunvisor for EZVIZ bullet camera. Might be ok for any camera with 63mm diameter. See dimensions on pic. Can be tightened with an M3 bolt and nut or with a zip-tie. The mounting plate available here:…
DIN53 pipe corner - 60 degrees
Adapter to mount Brita OnTap water filter on a Teka SP995 faucet Dimensions shown on picture. Thread size: ANSI 0.75in x ¾-28 UN Was prototyped as PLA, final printed with PA. When printing with PA don't forget to upscale the model in…
DIN53 pipe holder. Dimensions on the pictures. It's a bit loose, some shimming might be needed for better grip. The screw holes are not the best, was lazy to modify it…sorry - still might be useful to some. I was using M4 bolts and nuts +…
Wall mounted litterbox scoop holder. Two piece for easier cleaning. Wall piece can be screwed firmly on the wall, the box slides on-off. Mounting holes 54mm apart. 4mm diameter. Max scoop width: 112mm
Paper towel holder. Designed with swinging longer arms. Suitable even for jumbo rolls. Base has large surface so can be used - non damaging way - with 2-sided carpet tape. (Base has left and right version as I found this way holding on…
EZVIZ bullet camera and solar panel mount at 60 degrees angle. (If need to have it to the other side: mirror the model in slicer). Model was designed to be mounted to baseboard/fence with 8pcs of 4x20 wood screws. Camera base mounted with…
Cellar vent pipe needed protection from water (and bugs). The bottom is designed to slip on a pipe with outer diameter of 98mm and 4mm wall thickness (exact dimensions w/ toleration on the pic). Recommended to print 3pcs of retaining…
To redirect the hot humid air coming from the dishwasher during the drying phase from the bottom of the furniture. The prototype had too small lips so I had to tape it down, but the uploaded version already has the lips 2mm longer for…
Sturdy, printer friendly dog-poop bag holder. The one on the pics was printed with 0.6 nozzle, but due the threads 0.4 recommended. The 2 halves can be screwed (4pcs of 3.5x20 wood screw) or glued together. The uploaded model already has…
End piece of furniture telescope snapped. Instead buying a whole new stuff, part replaced with 3d printed one. Holds well for >2years now. Printed with PLA. Thread not modeled - it needs to be cut with tool, or with the telescope rod's…
Designed for my 3-step-ladder - approximate dimensions of the leg on the close picture. I printed the stuff from TPU for flexibility and softness to not scratch surface. Due elephant foot and possibly not the best printer settings for me…
Old laptop kept alive for parents ‘cause they "don’t want to learn any new gadget". Original speaker so old the membrane disintegrated. Printed some attachable external speaker covers and put some salvaged old Asus laptop speakers in it.…
Cat door with Simon's cat decor. The opening is 16cm wide and 20cm tall (164x204mm opening to cut on the door). The modeled frame is for 37mm thick door. The parts are mounted with 3mm diameter screws. (Heads can be painted to hide.) The…
Lidl collapsible rain barrel has a 1" overflow valve, needed a reducer to 1/2" so the excess water is disposed elsewhere. The reducer's thicker part has an inside diameter of 1" and the thinner part a ½" outside diameter. Both have small…
Cap for 6x4cm (60x40mm) fence pole For weather resistance recommended to print from ASA (or PETG). To save material print with 2-3 walls and low infill ≤10% (sorry for the picture taken with a potato)
Ant trap designed to low shake-out probability due pet safety. Can be poked down to reduce the movement (kickover) more. Cca. 7cm diameter. Screw-on cap. Added flat bottom version too. Print without support - bridging needed. Poison sign…
Shower cabin was by factory design ‘vented’ by a 90mm PC fan with not much effectiveness. This converter on the bottom has a 90mm inner diameter matching the shower cabin hole. The screw holes match the spacing of the 90mm PC fan. Upper…
Shelf holder for Ikea Fintorp hanger rail Can hold 83.5mm wide plank, glass, etc. shelf Print as many as you find safe to hold the shelf you want
Small hooks to hold edge of (cat)net. The hook's size is 16x12x6mm. Designed with 4x40 wood screws with countersink heads in mind. Small cap to cover screw is added.
These are all currently available results.
