Counting matching models…
A perfect way to simply grab Sonicare 4100, plop it into the enclosure and go, no need to remove your brush head! This was styled similar to another remix of the rugged box but due to size requirements and differences in the brush handles…
A practical, small, easy to use battery puller. Snaps on with a firm satisfying "CLICK" and easily slides off. Easy to hang on to, but small enough to clip on to your drone bag or keep in your pocket without losing it. Based off this…
This is a remix (link below) The holes are slightly smaller than a 3/8 bit depending on your printer settings, you can print with additional perimeters and drill through using a 3/8" bit (it will bite slightly into the plastic but should…
Will fit most Arris Surfboard Models (8200, 6141, etc). Complete re-design to fit the SB8200, re-measured, redesigned, and printed at least 10 different versions to ensure a nice fit on my own SB8200. Hopefully this fits better than…
We just recently got a 2016 Honda Odyssey which has a garbage bag holder ring, the ring folds down behind the center console and appears to be designed to hold a garbage bag. However, there wasn't a way to hold the garbage bag on the…
My doorstop bumpers recently deteriorated to the point of falling apart. When I ordered new silicone replacements from Amazon, I discovered that my doorstop's size is quite unusual, making it nearly impossible to find a readily available…
A car vent clip that securely holds a Yankee Candle Jar style air freshener in front of the flowing air of the vehicle. Prints without supports, though you really must print it in PETG, ASA, or ABS to ensure it doesn't melt or come apart…
FYI the fit on this isn't great - I noticed recently the measurements have been off for this model as well as others (not sure if it's always been that way or if Arris switched things a bit). Use this new model instead…
No supports are required, you can use a brim to ensure adhesion to the plate, but I found it to be fine without a brim.
Get that perfect fit for your Logi Litra Glow webcam light. I had issues with mine slumping over the edge of my monitor, this adds a stop such that the light will be able to sandwich the monitor a little better with less room to…
Replacement dart loading pusher for the DartZone Tomahawk. Picture shows the fitment of a prototype, but the final plunger product looks nearly identical and performs as well as brand new. I highly recommend printing at 0.2mm layer height…
Print in TPU Use .2mm layer height Use 10% infill - enough to add a little structure but still want it to be somewhat squishy - I printed in 95A hardness (which is pretty stiff, squishier TPU may need a little more structure, but anything…
I wanted to add a round hygrometer to my Sunlu drybox and discovered that the holesaw's I own do not fit the dimensions of the round hygrometer I had. Rather than purchase an expensive holesaw with the right dimensions, I created a shim…
Yolink flood sensor lifter - adds 2mm to the bottom of the sensor to help avoid simple mopping mistakes. *WARNING* this lifts the sensor by 2mm - water will have to raise 2mm before your sensor trips.
Uses 8x3mm magnets on the bottom I put a picture of the print orientation I used on my MK3s+. If you choose not to print the nubs on the bottom you could print it in a more conventional/convenient orientation. The magnet holes might sag a…
This is a hinged sun shade for an iPad 11”. It is designed to use the built in magnets for the Apple pencil pro. Once printed you will need to press in four, 5mm diameter by 3mm (they could be taller than 3mm) neodymium magnets in…
If you own something like an Ergotron LX (Same as the Amazon Basics Premium dual monitor arm) and upgrade to one of those massive 49" super ultrawide like the Samsung G9 - you'll want to continue reading. The G9 is 26lbs and the max…
I wanted to find a grommet that could try to keep the d-ring oriented the same way making it a little quicker/easier to hook the safety chains. All I had on-hand was red 95a TPU-AMS which is pretty stiff. I believe this could be printed…
This is a simple wall mount retainer for the 360 Electrical PowerCurve powerstrip ( http://360electrical.com/products-all/rotating/powercurve/ or http://360electrical.com/products-all/rotating/powercurve-2-1/ ) Print instructions…
Do you live somewhere where the temperature is below freezing for the winter? Then you may also want to use this. After we winterize our sprinklers, I like to unplug my Rachio controller as it will go 5-7 months without needing to be…
A lens adapter designed for the Microsoft Lifecam studio and a generic wide-angle lens and connect to the parts listed here: https://www.printables.com/model/258750-camera-side-mount-prusa-i3-mk3s The lens I used is here…
A case to house and protect your timers.shop programmer - you can find them here https://timers.shop or purchase off Amazon. Retains all original functionality To use: Gently remove the zip tie from the manufacturer Carefully slide the…
These are all currently available results.
