Counting matching models…
A slip case for Heltec Visionmaster E290: Easy to print, comes with several variations: Slim and fat designs. The slim design has 6mm clearance between the top of the LoRa transceiver module and the case back The fat design has 23mm…
A dimensionally accurate model of this board; all connectors, LED's, buttons and major protruding components modelled. Created for and used in designing this case .
Simple model of a clone Wemos D1 Mini, taken from direct measurement. Used for fitting/checking purposes in a case I'm designing. Category: Electronics
Easy printing freestanding pods designed to mount a 165mm car speakers in my boat. I might add grills later, but for now this looks good with the fancy speaker internals on display. Use stubby self-tap screws for the speaker mounting, the…
A simple drop-in holder for the XIAO ESP32S3 & Wio-SX1262 Kit from SeeedStudio. Has a generously sized USB plug access hole in the base, and a printed ¼' thread for a standard tripod mount (20 threads per inch). Designed for windowsill /…
Simple modification of this wonderful thing to remove the perch piece; some small garden species do not really need it, but their predators find it handy.. Category: Outdoor & Garden
A Simple Key rack with 3d lettering. Prints easily with 10% infill and no support needed. Print Settings Printer: K280 Rafts: No **Supports:** No Resolution: 0.2 **Infill:** 10% Notes: I printed this with 3 perimeters (0.4 nozzle)…
This is a series of remixes of the solid case top from the excellent snap-together VisionFive2 case by @mothdotmonster Use adaptive slicing for best results with these case models! The fan holes have simple vents but also have cutting…
An air-assist nozzle for 40x40mm laser modules equipped with a 20mm diameter, 8mm high removable lens and 35mm focal length. This is a set comprising of air assist nozzles with the following outlet diameters and clearance from the focus.…
After a few years of being pecked by birds and tangled with trees my Windex 14 was in poor shape. However the pin and bearing on it is still good (it's a jewel needle bearing, worth keeping) I designed this as a replacement vane system, I…
A wall mounted holster for a Bosch 36-4 eBike charger so I dont keep kicking it around on the floor. Holds the charger pretty securely, it's not going to fall out. Jan-2020 : I have uploaded a new version of this; with a clip to hold the…
A stand for the DSO138 oscilloscope with the (standard?) acrylic case. Heavy enough that it does not slide around the worktop as you connect it up ;-). I also incorporated some storage for probes etc. All the ports and connections are…
This bracket is designed for mounting a SeeedStudio XIAO+WIO module directly below a N type RF connector (specifically, directly below a fibreglass antenna). It provides a firm support for both the connector and the board below it. The…
A repair for the simple plastic Ikea drawer sliders used in some of their older ranges; in my case I was repairing a 15 year old bedside cabinet. The sliders have four pins 97mm apart (not all of these sliders are the same, so check!) and…
A small cyclone dust collector for my 1610 CNC, Works surprisingly well, only larger bits make it past the nozzle, and they are easier to clean later. The pictures show the results of a small carving job, all the dust was in the base cap,…
A vase that looks (to me, at least) a little like a tornado; hence the name. This is a sister model of my Coiled Vase , using the same maths base. The double twister is simply the single version but with twice the twists and height..…
Een eenvoudig sleutelrek Afdrukken met 10% vulling, geen ondersteuning. De 'dikke' versie was een Mk1, ik geef de voorkeur aan de slankere. Print Settings Printer: K280 Rafts: No **Supports:** No Resolution: 0.2 **Infill:** 10% Category:…
A simple little holster I designed for the remote (APC3-2300R) that came with soem KlikAan-KlikUit switches. It vaguely matches one I already have for another room controller. Print Settings Printer: K280 Rafts: No **Supports:** No…
A swivel-pin adaptor and base mount for Raymarine Dragonfly series fishfinders, should fit both 4 and 5 series models since they use the same case, tested on my Dragonfly4. Provides a neater/smaller mount onto flat surfaces then the…
A cap for this standard spindle design. Print as oriented in the stl, delete whichever style you do not want; the hole is sized for a 20x12mm rocker switch. Fit the lower half, I use a tight cable-tie to get a good fit. There are no…
Simple corner infill plates for any Kossel with a 310mm bed and 360mm extrusions on the vertices. Designed for my HE3D K280. My bed is about 1cm above the frame rails, so this matches that level. Underneath there is a large cutout running…
My Take on a clamp for the E3D V6 hotend on a standard He3D K200/K280 effector plate. This is designed for a 1/8" thread Bowden coupler (Like this: https://e3d-online.com/threaded-bowden-coupling ) mounted in the upper part. You could…
Useful for fitting parts; details taken from the data sheet; mount points and fan mouth correctly positioned. Note; this is a 45x42x18.5mm fan... not the 4020 size often found in printer supply shops. I'd gone through a bunch of cheap…
(Printed but not mounted yet, I'm still waiting for a windsock to arrive, once it does I'll post the usual action-shots) A simple windsock spinner and mooring post based on the ubiquitous 608-Z skateboard bearing. I designed this to go on…
This is a very quick remix of @Saur0n's nice woodpecker case: https://www.thingiverse.com/thing:2781593 The original has served me well but I was rebuilding/upgrading and needed some better access for all the additional wiring I threw at…
Replaces the stock injection moulded slider clamps of my He3D K280 kossel delta; the stock item is actually fine, but this version has a simple adjuster mechanism, and is sized for a 9mm belt upgrade I made. Updated with 4 new Models…
A simple and stable desk stand for the Testboy Pocket; I got fed up with it sliding about and being even harder to read when I've got it on the workbench instead of my pocket. Deliberately oversized for stability, there are holes for…
A simple piece to turn a cable bundle through 90degrees to exit away from a 2020 rail. Used to send the head loom of my CNC in the correct direction without chafing. I also used dome-headed bolts to reduce intrusion and chafing in the…
Accurate DC42 IR probe board model for use in assemblies and fitting. Dimensions taken from https://miscsolutions.wordpress.com/mini-height-sensor-board/ (see 'Appendix: Board Dimensions') Pins and capacitor legs extend realistically on…
Remixed PI top case with a hole that accommodates a 'Breakout PI+' prototyping board from here: https://www.abelectronics.co.uk/p/59/breakout-pi-plus (I quite like this board, it has reduced a rats nest of jumpers plus breadboard to…
This was created for Kali, who is 15+ years old, happy in her safe domain, but lives in an aquarium prone to overheating on Amsterdam's occasional 25+c days. It allows a 50mm 12v fan to be mounted on the feeding hatch hole of a Juwel…
Lots of dial gauges seem to have a 55mm body and the back plate 8mm offset from the pin. My cheap (unbranded..) one certainly fits that category. This is a design to let me mount it in my CNC so I can level PCB's before cutting tracks…
Combined with some 50mm tall feet (like this: https://www.thingiverse.com/thing:2250758 ) these blocks allow the 1610 Y axis rods to be re-mounted below the frame rail. and the bed brought back up to a sensible height. Perfect if you are…
60mm LED light ring holder with adjustable common actioncam mount; use any suitable bracket, the one I used came from here: https://www.thingiverse.com/thing:20830 The LED ring I used was O/D 60mm I/D 40mm and 1.5mm pcb thickness, this is…
A vase that looks (to me, at least) a little like a coiled rope; hence the name. This is a sister model of my Twister Vase , using the same maths base. The faceted model is the same as the hi-definition one; but with the polygon-count…
These are all currently available results.
