Counting matching models…
This is a mounting bracket for the Bigscreen Beyond Link Box . It's designed to (gently!) smush the link box against whatever surface you're screwing to, so don't tighten down too much! Hardware 4x 3x12mm countersunk screws Suggested…
Quest 3 Cricket Controller Adapter Update 18-05-2025: quest_3_cricket_controller_adapter_v2 Fixed some imperfections added mount screw mount holes Update 19-05-2025: quest_3_cricket_controller_adapter_v3 Reverse the thumb screw position…
Adapters that slide over the arms of an Apple Vision Pro to enable the attachment of a second Dual Solo strap. The arms have to be detached from the body using the special pin that was shipped with the AVP. I printed the adapters…
Pico4用バッテリー取り付けアタッチメント（Anker Nano Power BankおよびPD Reduxに対応）。固定は両面テープです。Battery attachment for Pico4 (compatible with Anker Nano Power Bank and PD Redux). Fixing is with double-sided tape. https://www.ankerjapan.com/products/a1653…
NEW FOR QUEST 3S! Quest 3 version here: https://www.printables.com/model/933285-oculus-meta-quest-3-stand-with-carrying-handle-for This is an Oculus Quest stand to be used when your Quest is not in use, and meant to facilitate easy…
You may need to heat up the camera mounts so you can bend it to make the camera fit easier. A little late to mention but the camera mounts fit my 160 FOV cameras, its a tight fit, I'm not sure of the compatibility with 130 FOV cameras.
The original plastic was thin and brittle. I designed and made these with ABS. The design is slightly larger than the original parts and doesn't shroud the spring below. The thumb pad is flat for printing and isn't as sticky as the rubber…
If you're here for a Valve Face Tracker Mounting solution that's nice and sturdy you've come to the right place! Just download the Frunk replacement, swap it for the current one, and then you're good! However if you wish to assemble your…
🧩 Features: Compatibility : Designed specifically for Bigscreen Beyond and the Apple Vision Pro’s Solo Knit Band Tool-free installation : Snaps into place without glue or modification Lightweight & durable : Balanced for strength while…
Use VHB tape or similar double-sided adhesive (hi-temp hot glue probably work fine) to bind to the halo. 3M VHB tape is a pressure-activated glue/tape hybrid that can still be removed if needed. Superglue fails to adhere to the…
This case is designed to fit the mini version of Matt's USB 2.0 hub found on the Bigscreen Beyond Discord. It is meant to attach to the soft strap and will fit both the BSB1 and BSB2. Recommended Print Settings: Print in as oriented in…
I wanted the Link Box on the front of my 19" Rack Case. Should fit any 5.25" Slot. Not sure about the mounting hole location. Your mileage may vary there. It's designed for M3 screws and Heatset inserts. The Big 30mm hole is for an USB…
This is a remake of the MattHub mount for the Bigscreen Beyond audio strap. The mount backplate is nearly identical to the one bundled with the hub, but my remake features 1.85mm holes instead of 2mm for a stronger fit with undersized…
use flat countersunk head M6*30mm x2 To attach the case to the pedal and hex socket head cap screw M5*30mm x2 To pcb
Summary: A lightweight, super thin, replacement facial interface for the PSVR2. The design is as close to the lenses as is possible, Every user can achieve the max FOV possible. Weight: 28 grams vs 62g on the lonny-k model (including…
A power bank addon for the KIWI Design k4 comfort Designed for the Xiaomi 33W Power Bank 20000mAh (Integrated Cable). I added some double-sided foam tape to the holder so it stays in place more securely, but it is not needed. May need…
I designed in Fusion 360, use at your own risk (hurts a lot) Use tree support or normal support for the overhangs
This is a remix of the original corner mount for Valve Index base station, since the newer mounts are smaller in size and the screw holes are now symetrical in relation to the mounting plate. Same as with the original design, no supports…
Description Anyone who owns a Meta Quest 3 knows this trick: cupping your hands slightly behind your ears instantly improves the sound. These audio enhancers are designed to recreate that effect — permanently and hands-free. The clip-ons…
Introducing the Playfold MegaBSB - an adaptor which replaces the face plate of the Meganex Superlight 8k to allow it to attach to the Bigscreen Beyond Audio Strap, while retaining the flip up display and angular adjustment capabilities of…
Sorry about the 2 floating pieces, just make sure to know they’re useless. Also PLEASE USE SUPPORTS NOT JUST FOR THIS FOR ALL OF MY MODELS. Please also be aware of the detached nails
be careful when taking off supports, you might break the light!
you can customize and be creative or print a copy of him and lay it down on the nextbot
for some reason certain printers don't print the side pockets on the bag, so be aware of that.
you can make them look like they're exploding by coloring them orange
this is a very hard print if you make it giant [which I tried.]
baaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa…
quest 2 Gunstock for kiwi extended grips FDM PLA ( grip ) walls 2 - 3 infill 15% need supports printed vertical ( stock ) walls 2 - 3 infill 5 ~ 15% printed vertical no need for supports --materials u need -- 1 -- 15.3x350or400mm rod 1 --…
A string based VR gunstock I designed as I couldn't find one that matched what I need, I have found it absolutely great but if you find it too long you can replace the centre piece with the "spacer" from the link in this description.…
This is an ESP32-CAM box, made specifically because no other case existed for what I needed
This is a ready to print, minimal-support desk statue of the Novabeast avatar.
I made this version of the Lumistera for a friend a while ago and thought I’d share it here. I highly recommend using organic supports for this print. It’s very stable once printed, and I’ve preserved as much detail from the original…
I always liked the design of charging station for Quest 2/3 like this . As there is no option for quest 1, I designed one myself with convinient USB C magnetic adapter. This design provides charging stand for quest 1 with hand…
This file is a replacement for the Quest VR controller cradle on the X-Arcade Tankstick-VR/Arcade2TV-XR controller. I purchased straps for my controllers and the loop it adds to the bottom prevents the controllers from fitting fully into…
If you use a fan in the Valve Index's front compartment, this modification of the visor by @LyzGameArt allows for airflow while it is attached. The slots don't need supports if you print the visor vertically from the top edge. The pins on…
if printing flat-ways, recommended to apply heat for ease of bending, i ran into layer de-lamination trying to attach it without. affix adapter to Vive DAS before you affix to the Quest 3. thank you very much for the .step files, op 🙏🙏🙏🙏…
Interface to add the standalone Leap Motion module to a Pimax crystal or Crystal Light. You can use the screw holes in your Pimax case (for the Pimax integrated leap motion module), or tape it to the bottom. Two versions in the file,…
the running pose has the weird long thing at the beak
I recommend setting a tolerance of -0.1 during printing to facilitate assembly. Print at 100% density in PLA. 20mm M4 screws and self-locking nuts.
I had to scale down the screw by 10% on the X and Y so that it fit the controller mount well. Print a second knurled thread to counter lock the top part if you need additional support. I've put built in supports on the controller part and…
UPDATE FROM MY FIRST FCU Hi, this project is a beta test because i have not received my printer yet, so give me advices for the mode Need tree spings, one for the trigger that is a compression spring 4,5 mm DIA by 10mm long, one for…
An aluminum pipe of 20x20 mm was used. Bolts and nuts M4 The controller mount is taken from https://www.thingiverse.com/thing:6289919
How to print: Print 2x with one mirrored!!! (not necessary with v4) Print laying down flat Print solid Print with build plate supports Assembly: Remove the 2 screws holding the pimax dream air headstrap bracket on Remove the bracket and…
This gasket maximizes your FOV and gives you a more comfortable experience laying down on your side than the default pimax gasket. I designed by manually reverse engineering the dream air as they still have not released any 3d files for…
Recommended print settings: Material: PLA or PETG Layer Height: 0.2 mm or less Infill % : 50+ Supports: No Print Orientation: Default as modeled
This gasket improves stability by replacing the hinge with a fixed element with added brackets for a soft strap. The current version (V1), was modelled for my face shape so the fit may not be ideal for everyone. I include 4 variations…
Broke my headstrap pivot and I couldn't find another for sale. This works great. I suggest printing with PETG and turning your temperature up about 10 degrees to ensure better layer adhesion. Be careful placing the part as too much force…
Tired of having to constantly readjust the head strap on your VR headset? Frustrated with having to loosen your head strap and peek through the nose gap to see your computer monitor? Well here's your solution: Many have asked and searched…
This ‘extended’ version of the adaptor allows you to mount the BeyondEx audio solution to the Shiftall MeganeX Superlight 8k using its included top strap through the MegaBSB top strap loop. It features an extended face pad area to allow…
Use your existing Quest 3 strap on your Bigscreen Beyond to get maximum comfort! The mod is simple and snaps right in, you may want to add 2 cable ties per strap point just for insurance but the snap fit with PLA is perfect. Untested with…
Remix of Pimax Dream Air Ancillary Gasket (MAX FOV) to be able to fit a mid strap from a VIVE DAS strap.
A stand for the Meta Quest 3S + BOBOVR M3PRO + BOBOVR CD3 + BOBOVR B2 kit, designed for screw-free assembly, prints on a 220x220 AD5x table. Type-C cables are routed through the back. Since it runs on B2 batteries, there is no hole for…
Wanted a solution where only one solution exists but too expensive for me. I did use part of the shoulder pieces from BMKVR - Marksman but can't what site I got this. But the "barrel" assembly and holders for the controllers was all my…
infill-100% I mae this model because batterys in my controllers blown up with acid, that had ate these parts? so i repaced them with this
This model is intended to mount base stations of the Valve Index on walls of a room with Artika Sonolok paneling, without holes or screws in the wall The model is not perfectly symmetrical, to match the hole spacing and size of the Valve…
Covers the Beyond 2 Linkbox USB-PD Adapter from MMI Modular. Perfect for protecting the adapter when stashing it "who knows where". Just seat in the bottom portion and slide the whole thing in until it locks; no additional hardware…
Protect your privacy with this simple, dock-mounted privacy shield that hides your headset's front-facing cameras while it charges! Prints with minimal supports, easy to install, and provides excellent coverage without touching or…
That's one big piece of gum! A modified version of Phys' All-In-One USB dongle that uses an Adafruit CH334F Mini 4-Port USB hub breakout instead of the original disassembled USB hub the project originally calls for, making it easier to…
The STP model of the PImax 8KX (frontcover, half) to allow for modding or re-printing parts.
.print in white for the effect to work best .pla works well .if you have warping issues, use a brim .if you have any problems, I'm here to help THERE MAY BE MORE PICTURES LIKE THIS...........................
This is a simple IR shield to block the Babble tracker's infrared light from hitting the Bigscreen Beyond's tracking dots. This helps prevent tracking loss and grey screen flashes. Prints without any supports. Fits the official Babble…
I wanted a stable spot for the top strap, as well as a mount for my USB hub, so I looked at other designs out there and designed this clip. There is a hole for an M2 bolt, for any additions you would want to mount to the side of the…
My "knuckles"-style straps didn't fit around the knob of my KatWalk, so I made this instead. This design is intended to go on the right side, since the water bottle holder is on the left, but the model can be mirrored in your slicer if…
this is baldi from baldi's basics the classic game idc what you do with this model idc if you rig it idc what you do with it idc
meta quest 3 controller case made from tpu tested got original 3d model of the controller from paul_delta @paul_delta_13
Coque de contrôleur VR M1911 pour Meta Quest3
Wanted a place to put the oculus instead of leaving it just sitting around.
A Base staton mount that doesnt require drilling or damaging your walls. These mounts use standard Command Large strips and provide a very strong/secure vibration free mount for your base stations. BOM: 1x 1/4-20 x 1/2" long screw (such…
![Lethal ape sandman\ashy monster. [NEEDS SUPPORTS].](https://media.printables.com/media/prints/4b95145a-408c-434a-832d-fe114967a747/images/12068550_9cd13528-1113-4d05-96ab-7250aa3aff0f_cd0e7920-5f45-417c-98f1-bb8933167c16/screenshot-2026-02-16-103523.png)
