9,658 models
July 27 2022 house keeping note: Somehow, reviews and makes for the older version of this fan duct have been showing up on this page, and reviews and makes for this updated version were showing up on the old versions page as well. To…
Inspired by Mikolas Zuza Link: https://www.prusaprinters.org/prints/10-extruder-rotation-vizualizer What you need: Super Glue 8x3mm Neodymium Magnet 3D printed Visualizer Montage: Just glue the magnet correctly in the center of the circle…
This object can be used to calibrate linearity correction factor for extruder motor. More info in https://help.prusa3d.com/en/article/extruder-linearity-correction-calibration_2254 Print instructions Print with PLA
Extruded fractal flake prototype. A predecessor to the fractal flake vase I made some years ago. The basic shape and parametric model is almost the same: A variation of the Koch-curve with hexagons, which changes in rotation and…
Useful for finding the right distance of the Super PINDA from the print bed. The optimal distance for the Super PINDA is about 1.5mm. That should get your optimal Live Z/first layer calibration to somewhere around -1.00, so you'll have…
- Prusa Print files added! - Presenting you: my iteration of a Roll up Chess set! Please like, share, download, rate and all the amazing good stuff :) I have seen many roll-up chess models, but none that would fit my needs. What I really…
(for Bambu, check below) Please like, share, download and all the amazing good stuff! Since this is my final model in my "Single Extruder - Dual Color" series where I managed to put 3 colors together into one model! Not counting the…
Size: 61mm x 47mm x 42mm Filaments: PLA Prusa Orange (orange) and PLA Vanila White (white) Note: All parts need to be glued.
Test the maximum printing speed of your extrusion system! The model can be scaled in X and Y to fit your buildplate. There is a small notch every 2 mm to indicate a speed change. GUIDE Load, orient and scale the part to your liking Enable…
This handy little piece turns a regular M3 nut into a T-nut that fits into a 2020 / 2040 extrusion ( e.g. Ender 3 frame ) in order to attach anything. Some pictures show an original Ender 3 M4 T-nut for comparison. Prints best with no…
Update (July 13th, 2022) After receiving feedback about mounting the shield and the occasional break, I have decided to strengthen a few parts of the design to prevent breaking during support removal, slipping off the left mounting point,…
EDIT: I forgot to add in the name kindly given to my cat by Mark "Velocity Painting" Wheadon ( https://t.co/LF6wu0B4sd ): Schrodinky! A couple of weeks ago, I posted a very cute picture on Twitter of a British Shorthair kitten sitting in…
I would appreciate a lot if you could support me giving a like and downloading, thank you guys. You can also visit my profile and suport my other 3D models. Check out my latest models:…
UPDATE: Version 3 included with better tuned dimensions and fixes based on feedback. UPDATED UPDATE: Thanks to Crosslink for featuring this in his video!! The extruder on the SV06 can get quite hot, due to the weak stock fan, especially…
Because changing nozzles with the supplied multi-tool was too wobbly for me, I developed a simple tool to hold the hotend more stable. As can be seen in the CAD image in cross-section, the tool is designed in such a way that the hotend…
I mostly print this on 0.25 draft in prusa slicer. No infill to make the clip more bendable. Just push the sides together and push in the extrusion. Then click the inner towards the extrusion to make the click. Perfect for cable…
Description This is a fast and easy to print model to calibrate your new filament. It can be used to find the right settings for the extrusion factor to get the right wall thickness. It is designed with a 0.86 mm wall thickness to meet…
This is a Flow Rate Calibration Test specifically designed for PrusaSlicer , as it does not support per-object settings. These models are optimized to use as little filament as possible while still providing accurate results. There are…
To add the filament profile to Bambu Studio, follow these steps: 1. Download the .zip archive - the .gcode file is empty and can be ignored 2. Extract .json file from zip archive 3. Open Bambu Studio 4. Go to File →import→import…
T-slot covers provide protection from debris buildup and can also be used to manage wires and cables recessed within the T-slot. They can also add a finishing look to your project. So... Since I couldn't really find what I wanted I made…
This print allows the use of a Bowden tube direct to the extruder when printing hygroscopic filaments. The top is threaded to accept a PC4 M10 fitting (which is actually a 1/8 BSP thread). This fitting has a larger hole inside, so it…
This is version 2 (V2) of the Delta-P fan duct for BEAR. It has several updates compared to the original: Easier to print Better cooling Refined flow path CFD optimized Even cooling front to back and left to right Improved visibility of…
I had many issues/errors/problems with my mk3s+ mmu2s while printing multi color. I can tighten idler screew to not have stopped filament, but than I had issues to work IR sensor right. I loose scree, IR sesor was working right, but…
This was designed to be used with a cylindrical magnet (8mm diameter by 10mm long) This is a press fit, no glue is required... Print instructions 200 microns works fine !
MK3 Stealthburner V0.5 This is my Stealthburner case mod for the original mk3s+ extruder. Note that this is only a design upgrade and the upper ‘fan’ is actually a extruder visualizer (I may also do a version with an active fan in the…
Watch the motion of your 3D printer's extruder, Star Wars style. Embed a 6mm X 2mm tall magnet while printing, multi-colored as well with a single extruder (swap mid-print). Print instructions I used .1mm layers, since I wanted this to be…
Ho Ho Ho! 🎄 Imagine a Christmas tree made of not just two but three parts , each twisting into the other to create a double vortex illusion – yes, it’s twice the magic! The twisting motion makes this tree look absolutely mesmerizing and…
There are lots of Nextruder bin designs for Zach Freedman's Gridfinity system, but none of them worked for my needs. So I made this one from scratch. If you are unfamiliar with the Gridfinity system, watch Zach's original video below.…
Ho Ho Ho! 🎄 Imagine a Christmas tree made of two parts that twist into each other – yep, you twist it into place. This creates an impressive vortex illusion , making the tree look almost magical. Caution: The illusion is so captivating,…
The endcap is held by a middle pin into the profile. The small standoffs prevent rotation. There are 5 Versions since different extrusion brands also have different hole sizes: with a pin for a 5mm hole with a pin for a 5.5mm hole with a…
This is designed to snap-on a 2040 extrutions, like used in the Bear Upgrade for the Prusa Printers
This is a PrusaSlicer project with the settings from CNC Kitchen. The Volumetric Flow starts at 7 mm³/s and goes up to 25 mm³/s in 1,5 mm³/s increments. Default settings are for the Prusa MK4. step by step to individually adjust the…
Literally just took the original Prusa Mini gcode file and in text editor changed the M92 line to M92 E415 in order to print well with a BondTech Extruder. Thanks to JamesHZ (https://www.printables.com/social/116023-jamehz/about) for…
Size: 82mm x 52mm x 41mm Filaments: PLA Blend Viva La Bronze (gold), PLA Vanila White (white) and Silk PLA+ Rainbow 02 (shiny) Note: All parts need to be glued.
I was having a lot of trouble printing with flexible materials like Ninja Flex on my XL so I decided to modify the existing parts to try and eliminate the filament jams. Initially i started with reducing the friction from the filament…
As stated by the original project here : Sometimes the filament gets stuck between the stepper motor and the drive gear of the nextruder. This design closes the gap between the stepper motor and the drive gear, thus limiting this source…
T-nut for 30x30 V-Slot aluminum extrusion like PRUSA MK3S (8 mm gap) compliant with M3 nut. I used them to install the Rubber Feet Support for Prusa MK3 by Volan on the PRUSA MK3S If you like it, plz post a make :) Print Settings Rafts:…
Changing colors between layers is a known and easy to use feature in Prusaslicer. If you want to change filament within one layer you usually need the MMU. But with virtual extruders and some prearrangements in the model and slicer, this…
Endcap for 30x60 mm aluminum extrusion.
Simple Dust Cover for the aluminium extrusions. Update 7. Nov 21 Additional slim version for those who have the bearing fixation as shown in the picture below, to prevent it scratches over the cover.
I noticed that the wrench with chamfers is very close to fitting IBnobodys heatblock clamp so i remoxed the STL to make
Update: This part was recently changed. If your extruder was manufactured after February 2021, you should use the 2021 version. Earlier printers will have to use the other. I found it very difficult to set the very sensitive extruder…
How-To Print: Recommended layer height: 0.10 mm Color Change (Please see the tutorial below) Support: No needed Let the Visualizer cool down slowly on the printing plate to avoid being bent. How-To Change Filament Color: Montage: Just…
Remix of MayrM's knob but scaled down to dia 33 mm. The original seemed too clumsy. The part attaching to a stepper's shaft is scaled to 101%. Fits to stock extruder on Anycubic Kobra Go, should be compatible with Ender 3 and other…
Nexdruder Lever Mod from Jürgens Core One Automatic Chamber Vent.
I “remixed” the original extruder lever brace from https://www.thingiverse.com/thing:3935900 . Main reason was to be able to mount a ADXL345 sensor. I had to calibrate klipper3d with help of this sensor. You can just put the ADXL345…
Minimiert Verwirbelungen am Bauteil durch den Hotend Lüfter, bei empfindlichen Materialien die ohne Bauteilkühlung gedruckt werden wird Warping verhindert Druckempfehlung: PETG, Nobufil ABSx oder besser Nozzle 0,40 mm Schichthöhe: 0,15 mm…
This is an Extruder Visualizer based on the epic John Cleese character from the Ministry of Silly Walks sketch by Monty Python. Check out https://www.prusaprinters.org/visualize-extruder-motor-movements/ for more info on how to use it. I…
Fits onto the misumi 3030 extrusions with the 6.8mm hole and 8mm slots. Held by the middle pin and fixed against rotation by the small standoffs.
This print is only 40 minutes, uses only about 1.5g of each filament. The layout matches the purge matrix so you can easily enter your values after eyeballing the clean point. You will get cleaner prints and probably save a lot of…
This is a guide for tapping an M5 thread into the end of I-type 2020 aluminum extrusions. These are the type with 5mm slot width. The model was inspired by existing designs like this one:…
To add the filament profile to Bambu Studio, follow these steps: 1. Download the .zip archive - the .gcode file is empty and can be ignored 2. Extract .json file from zip archive 3. Open Bambu Studio 4. Go to File →import→import…
Material-saving distance tower test model suitable for dialling in most of the printing profile parameters, including retraction, flow/extrusion rate, temperature, bridge, ironing settings, and certainly many more. Optimized for 0.4mm and…
Finally, after great response, I ported the files to the platform they belong to. makes higher printing speeds at flexible materials possible, retraction should work too. Main changes to the original: shifted stepper position to corrected…
I printed this in ASA at 100.5% scaling to allow for some shrinkage. using variable layer height I made changes to fix the misalignment of the part cooling fan and the duct/bracket that wraps around the heartbreak, above the hotend. In…
This is the fourth (and maybe final) installment of my Single Extruder - Dual Color series: With previously Burp the Derpy Frog , the Dutch Cow and the Easter Egg Collection As with the previous ones, you can print both parts of the…
2020 Leveler Pads for Aluminum Extrusions - Stabilizer - with M6 Threaded Leveling Mounts Overall dimensions: 85x20x18mm double 50x20x18mm single Suitable for:…
Fan mount and air flow duct to allow the use of a larger and more powerful Noctua (or other 40 mm) fan to improve the cooling of the cool end of the extruder. This will help when printing PLA in particular to avoid heat creep issues. The…
Simple Archimedes spiral extruder visualizer. Color change at 1mm level. Glue/use 3x 8x2mm magnets (or 2x 8x3mm magnets) on the back in the recessed circle. Print in PETG/ABS if you have an enclosure, otherwise it will likely warp from…
Introduction This accessory will be used in one of my projects currently being developed for the PRUSA Mk4. Although I'm aware that there are several solutions for this purpose, I have chosen another option that will fit into the…
This lightweight rotor-style visualizer mounts onto the shaft of the Ender 3 V3 SE's silver extruder stepper motor. Designed for effortless visual monitoring, it rotates as the extruder motor turns, clearly indicating direction and speed…
A simple to print dual color On Air warning sign. Just swap the filament color and have a dual color print. The combination of colours is yours to choose. The base is printed in a single colour, black, has 4 holes on the back for easy…
These holders hang from the XL's side extrusions to store your extra Nextruder nozzles. When the nozzle is in an extruder, the holder becomes a label that clips on to the extruder to remind you which nozzle is currently in use. The .3mf…
Geändertes Cover, das besser passt und Probleme beim Kalibrieren der X-Achse verhindert da das original Cover manchmal nicht ganz anliegt ########## Übersetzung des original Textes von @Stefan_106413 ########## Die originale Abdeckung für…
Needed a box for my quick change Nextruder Hotend Assemblies. Holds 3 completed assemblies, and 16 assorted print heads. I enlarged the box, but also shortened its height. Be careful the first time you try to close the case or you might…
Mounting a E3D Revo Micro on Creality Ender 3 , CR10 , Sunlu S8 and many more printers. Bowden-Setup and Direct-Extruder with Annex Engineering Sherpa Mini ! Silent Setup with 5015 Blower and 40x40 axial Fans. Detailed build instruction…
A simple two-piece box that stores a full Mk4 Nextruder hot-end assembly (Heater, Thermistor, Heaterblock, Mk4 Nozzle or v6 adapter+v6 nozzle) as well as one to three v6 nozzles. It has a few small features on both short ends to allow it…
I had a heck of a time trying to find an extruder indicator that will work with my new V3 SE. The few that were out there did not give me what I wanted. So, I took the good work of Toni H and updated it to work with the new extruders that…
Remix of GLeZz's Red Valve Extruder Visualizer to fit bowden extruders on Anycubic Kobra Go / Ender 3. Downscaled. Print with supports, split the valve into two parts to save material, print the nut separately. Fits to stock extruder on…
EXTRUDER COVER FOR KINGROON KLP1 210 My print is printed from Graphene PET Printed on 3 perimeters, filling 40% with a wall height of 0.15mm. Supports are not needed I recommend printing from ABS, ASA, PET material. Enjoy
This is a Simple Mount for the X-Endstop w/ Microswiss NG Extruders, For use with the original screws. The original mounting position doesn't allow the NG Extruder adaptor plate to hit the end stop switch, this simply p rovides a new…
Overview Inspired by the "dual color, one-extruder" contest, I designed this model in Fusion 360 with a fun passthrough mounting. You can use this model as money box or pencil cup : as you want ! Printing Printed with 0,4 nozzle, 0,2 mm…
This is cover for Original Prusa MK3S+, to mimic the design of the Extruder cover for the Original Prusa MK4 and XL.
This is a model that I designed to help me make some custom aluminum extrusion pieces for a Voron 0.1 that I am building. While it was used for custom pieces, it could also be used to help you if you cut or source your own aluminum…
Small switch box. Made to be mounted on extrusion profile. You need to drill hole where you want your cables to go in.. Printed in PLA 0.15 Layer height 20% infill
I designed this ender 5 spool holder for my Ender 5 with direct drive extruder. It sits in the back by the y-stepper motor and it conveniently slides into the frame so you would only need: 2 screws and 2 t nuts that already came with your…
Another endcaps for 2040 extrusions. Press fit no screw needed. Printed with ColorFabb XT-CF20 4 perimeter 0,15mm. Frame from Blackfrog.PL Hope you like it
Nextruder Nozzle Holder with box, up to 7 Nozzles MK4_Nextruder_Nozzle_Holder_v2.obj: The column in the middle is ~10mm higher
I wanted to make the fan shroud to cool off the motor of in the extruder of MK3S+. It is pretty hot during summer here. The original Extruder Cooling Fan Duct works great with stock extruder fanshroud. Because I wanted to make it work…
Using the Mosaic Palette 2 with my Prusa i3 Mk3S+ , I first tried one of the available extruder clips based on a rubber grommet. But like mmontminy , I found it not very secure. But I couldn't use his MK2.5s-MK3s Palette 2 Extruder Clip…
This print elegantly relocates the Ender 3 extruder from behind the x-axis gantry to the front. This makes the extruder easier to access as well as keeping the bowden tube fully in front of the z frame. This way, the bowden tube doesn't…
Made for Prusa MK4 and Prusa XL but fits with every E3D nozzle. You can use it with the Prusa Nozzle Replacement Tools. No supports needed.
The Wu letting you know you rollin! Protect ya neck with this killer bee of an add-on. I printed it from Matter3D Basics sun yellow PLA: https://www.matter3d.com/products/basics-series-pla?variant=42420619772081 0.40mm nozzle 0.15mm layer…
If you want to change your Prusa extruder motor to an LDO extruder motor, you should know that you will need to mount it with the connector facing left or use this mod. It is a variant of the original Print fan support for a Mk3s/+,…
I made a standalone mod for the CR10S, and needed to raise the height. These feet are compatible with any printer that has 40mm wide extrusion on the bottom of the frame. Recommended Print Settings for the Feet (can increase values to…
My Anet A8 Extruder base on Original Prusa i3 Category: 3D Printer Extruders
I edited the original model from In3DSpace to fit 7x14mm extrusion u-channel.
You need the following 2x M2.5x4.0x4.6 Brass Heat Inserts 5x M3x4.0x5.0 Brass Heat Inserts 6x M3x6.0 Screws (And maybe 2x M3 Washers between probe mount and the extruder motor) 2x 2.5mm Cable tie (For cable management) Fan Duct:…
I build this gantry to check the righ Extruder Rotation in your printer
Changed to fit tp-link UH720 with charging ports on the side
Vor- und Nachteile auf einen Blick: + PTFE-Schauchverlängerung + Filament selbstsgeführt und Filter durchstechend + einfach zuschneidbare 1 cm^3 Filterstücke + staubdicht (ggf. auch Feuchtigkeitsfilter, wenn man mit Silikat statt Schwamm…
When looking for a sleek, simple, logically way of storing Nextruder nozzles many of the printables are so close to fit my desire for what i'm looking for. That was: no chance of flying nozzles when bumping into them when they are hanging…
Update: December 1, 2021 – Adjusted the outer rings on both models to provide a cleaner contrast. This extruder indicator features the ancient Aes Sedai symbol and can fit a 8mm x 3mm or smaller round magnet in the back. There are two…
Gridfinity base mount on 40x40 extrusion panel. Print in 45° angle and use default support.
I could not find a model for endcaps for 15m wide extrusions so I designed some. Just print at a normal .2mm layer height and snap onto the extrusion. It sure does beat buying them and having to wait 😃.
This is cover for Original Prusa MK3S+, to mimic the design of the Extruder cover for the Original Prusa MK4 and XL.
UPDATE: my desing is no longer up to date and therefore not needed. i still leave it online for comments Use the original files there . Yesterday the original printed and then determined that a few minor things should still be changed.…
90 degree corner for 2020 aluminum extrusion. I used this for my diy printer.
I printed with PETG and organic Support.
![Filament Filter Pipe [FFP] cleaner extruder upgrade for Prusa Mini and for PTFE extensions PC4-M8](https://media.printables.com/media/prints/196746/images/1820520_431f3620-c448-4583-abf9-6c222d51ea44/mvimg_20220506_125457_529.jpg)
