2,801 models
The orange Gyro 7 in the pictures is printed in 0.20mm layer height Printing Material: PETG (PLA makes the joints too loose when using the normal skeleton and too tight for the tight Skeleton . Assembly is also more difficult in PLA.)…
Print approx. €1.63–€1.99 excl. taxPreliminary estimate for PETGSource material: PET
This is a series of test prints which were inspired by the following MIT publication : Snap-Fit Joints for Plastics - A Design Guide https://fab.cba.mit.edu/classes/S62.12/people/vernelle.noel/Plastic_Snap_fit_design.pdf While the above…
Print approx. €0.11–€0.14 excl. taxPreliminary estimate for one variant
I wanted to do a jointed model for the Printables contest. Jace1969 (who has a ton of great SW models) had this ATST model, but it was a solid model so I diced it up and added 14 joints to make it into a posable design. I was trying to…
Print approx. €0.81–€0.99 excl. taxPreliminary estimate for one variant
I recently had someone request that I make them a Jellyfish. I found a nice articulated model on Thingiverse but it had some issues with the .stl files and also required glue. I decided to re-mix this model and eliminate the need for…
Print approx. €0.60–€0.74 excl. taxPreliminary estimate for one variant
The clips supplied with the general car mounts don't hold well and that bothered me. Inspired by various similar holders, I came up with this version, which can be printed horizontally. The horizontal printing position improves the…
Print approx. €1.30–€1.59 excl. taxPreliminary estimate for one variant
Introduction This is a concept for greenhouse based upon a geodesic dome using 3D printed articulated joints, PVC pipes, and greenhouse plastic. Unfortunately I don't have the funds at the moment to realize the full concept but the 3D…
Print approx. €1.33–€1.63 excl. taxPreliminary estimate for one variant
Recommended print settings: Material: PETG Layer Height: 0.20 Infill % : 15 Supports: No Print Orientation: Default as modeled. As seen on Jelle Romers video: And article:…
Print approx. €2.16–€2.64 excl. taxPreliminary estimate for one variant
Printed in PLA Plus, .2mm layer height and organic supports
Print approx. €0.90–€1.10 excl. taxPreliminary estimate for one variant
Has your Dummy 13 been “Chalk Lined”? Too weak in the knees to even stand up? After printing your Dummy 13 or other articulated model, you may have a loss in stiffness of the model when the 3D printed joints wear or stretch. This can…
Print approx. €0.23–€0.28 excl. taxPreliminary estimate for PETGSource material: PET
This is a study on print-in-place articulation. I wanted a small anatomical figure that was jointed. I found other great designs where you print the respective parts then assemble, but scaling down caused difficulties as the smaller snap…
Print approx. €2.14–€2.62 excl. taxPreliminary estimate for one variant
I have printed them with 100% infill. So far, they have proven to be surprisingly robust.
Print approx. €0.29–€0.35 excl. taxPreliminary estimate for one variant
This is my model of TARS from the movie Interstellar. TARS body consist of 4 legs, this model uses magnets to form joints and keep everything together. The magnetic joints slides along the full leg length which makes for a very flexible…
Print approx. €3.60–€4.40 excl. taxPreliminary estimate for one variant
Freddy FazBear FNAF - Based Joins Dummy 13
Print approx. €1.39–€1.70 excl. taxPreliminary estimate for one variant
Bought a cheap wardrobe (too cheap, may be) which collapsed after moving too much stuff into it. These connectors were used to repair it. The small cylinder is only if you have the need to reinforce one of the tubes if it is folded.…
Print approx. €2.31–€2.82 excl. taxPreliminary estimate for PETGSource material: PET
Simple remix with joined parts of https://www.printables.com/model/73423-logitech-g915815-vertical-keyboard-stand Update 11/11: I also recently purchased an Apple Magic Keyboard 2, the fit isn't perfect but it works well
Print approx. €2.13–€2.61 excl. taxPreliminary estimate for one variant
A simple joiner that allows you to connect two ends of a length of 6mm wide GT2 timing belt. The joiner is shaped so it does not interfere with the teeth of the belt. Print with largest surface down. Slip the ends of the timing belt into…
Print approx. €0.10–€0.12 excl. taxPreliminary estimate for PETGSource material: PET
Printed in two halves, because of the large size. No support needed. Connected by 2.5x8mm cylindrical pins and/or glue. There is a small gap when the box is closed. To make sure no parts escape from the organizer when the box gets tilted,…
Print approx. €16.41–€20.05 excl. taxPreliminary estimate for one variant
Rpi camera v2 holder/mount with articulated snapfit joints and mechanical interface to the ethernet RJ45 female connector of your raspberry 3/4. The snapfit joints allow to adjust the camera orientation. All mechanical interface are…
Print approx. €0.76–€0.93 excl. taxPreliminary estimate for PETGSource material: PET
Tent Joiners - middle and edge parts
Print approx. €4.06–€4.96 excl. taxPreliminary estimate for PETGSource material: PET
1 central 4 left 4 right sticks folie
Print approx. €3.05–€3.73 excl. taxPreliminary estimate for PETGSource material: PET
Double-breasted dovetail joint partially embedded, teaching aid for joiner and carpentry in secondary schools. Oboustrabbý rybinový svlak částečně zapuštěný, výuková pomůcka pro obory truhlář a tesař středních škol.
Print approx. €1.73–€2.12 excl. taxPreliminary estimate for one variant
Needed parts: Arduino2560+ramps+reprap smart controller+power supply 12v+2xnema17 with min.a4988 -2x radiator from ender3 -2xheatbreak all-metal(drilled with 2.6mm drill bit for around 10mm) -2xextruder mechanism from ender3 -1xheatblock…
Print approx. €0.59–€0.72 excl. taxPreliminary estimate for PETGSource material: PET
This model of a vase is inspired by the stunning basalt columns at the Giant's Causeway in Northern Ireland. The model can be combined with a glass insert to make it waterproof. The glass insert can be easily removed for easy cleaning.…
Print approx. €6.32–€7.72 excl. taxPreliminary estimate for one variant
They are weird, they are cute, they are fun - and oh, they are wobbly ! A fanart design from my favorite game this year: Wobbledogs . Mingle is the first dog that you get in the game, a basic good doggo that teaches you how to play. I got…
Print approx. €0.57–€0.70 excl. taxPreliminary estimate for one variant
Design to fit 9x5mm self-adhesive cable channel (EAN nr: 8414419240520). Printed in 0.2 without support
Print approx. €0.24–€0.29 excl. taxPreliminary estimate for PETGSource material: PET
This 3D printed enclosure (three parts: left, middle, right) holds two 8 module Max7219 display boards. Included are the .stl files and the Fusion 360 (source model) .fd3 file. It also requires a front piece of red acrylic plastic 1/8"…
Print approx. €8.67–€10.60 excl. taxPreliminary estimate for one variant
This is for joining Banana plug test leads. Here is the Banana plug to Pin Tip plug version... https://www.prusaprinters.org/prints/53545-banana-to-pin-plug-joiner Print instructions I used ABS but PLA should be fine.
Print approx. €0.48–€0.58 excl. taxPreliminary estimate for one variant
Connector for a broken ball chain with 4.3mm diameter balls, connecting thread 2mm. I used eSun PLA+ at 0.12 layer height, 3 walls, 20% infill. Printed open side upwards with a brim. Balls needed squeezing into place with pliers. This is…
Print approx. €0.13–€0.16 excl. taxPreliminary estimate for one variant
!! Attention: See the new upgraded model here ! !! While the original print-in-place bearing is fantastic and works very well, the nature of the print-in-place arrangement means that the underside of the top part ends up a little messy.…
Print approx. €1.98–€2.42 excl. taxPreliminary estimate for one variant
I designed this things for you so please leave a like or a comment if you don't like something and i'll be very happy to se your makes so don't forget to post them. :)
Print approx. €0.08–€0.10 excl. taxPreliminary estimate for one variant
Don't find what I was looking for to put in my Lack Table Enclosure, so I created this one. I try a few good design I found around but none was really what I was looking for… I don't want to see any screw, I also want a track to put my…
Print approx. €1.26–€1.53 excl. taxPreliminary estimate for PETGSource material: PET
Upgrade selfie stick v2 for Radiacode102/101. This spacer-joint allows a smooth change of the RC102 mount. https://www.printables.com/cs/model/552255-radiacode-102101-selfie-stick-v2 Installation: if I already have version 2 printed and…
Print approx. €2.01–€2.45 excl. taxPreliminary estimate for PETGSource material: PET
Designed for 3mm hardboard with a height of 40mm. I used these connecting corners together with hardboard 3x40x650mm (4 pcs) to create side protection of the laser work surface.
Print approx. €1.35–€1.65 excl. taxPreliminary estimate for PETGSource material: PET
Spoj dvě dřevěné desky díky téhle vychytávce--Join two wooden boards thanks to this gadget :O Doporučuji tisknout z PLA nebo PET-G --I recommend printing from PLA or PET-G Prosím dejte mi like nebo tohle stahujte,doopravdy mi tím…
Print approx. €0.14–€0.18 excl. taxPreliminary estimate for one variant
The Garmin DriveSmart 86 has a 22mm ball joint instead of the other model's 17mm, so this converter lets the GPS be used with the standard mounting equipment. For printing, I used: 6 Perimeters 100% infill .20 layer height I have tested…
Print approx. €1.04–€1.27 excl. taxPreliminary estimate for one variant
Two grout floats in 2 different sizes: small (7 x 15.6cm) with handle smaller (7 x 10cm) with crim grip Don't forget to (hot glue 130C) add a foam float (I got mine from the hardware store), I recommend at least 5mm larger foam as the…
Print approx. €1.22–€1.49 excl. taxPreliminary estimate for one variant
I have a rather large window in my bedroom, but didn't want to spend hundreds of dollars for a custom set of curtains. So I ended of buying two sets of cheap curtains off of Amazon. The thing is, I did not like having to adjust them to…
Print approx. €0.17–€0.21 excl. taxPreliminary estimate for one variant
I wanted a Magsafe tripod for my iPhone 12 but already had the standard GoPro tripod that comes bundled with the camera along with an assortment of other mounts. So I got an ESR Halolock Car Mount which has pretty strong magnets and made…
Print approx. €3.38–€4.13 excl. taxPreliminary estimate for one variant
This is a ground glass stopper for the standard ground glass size 29/32 mm. It has a rounded head and a pin from which condensate can drip back. Please check the material beforehand to ensure it is suitable for the intended use. Depending…
Print approx. €1.31–€1.60 excl. taxPreliminary estimate for one variant
Ersatz für die rechte Endkappe unserer Arbeitsplattenabschlussleiste. Die Skizze ist ähnlich, der innnere Aufbau etwas anders. Translation: DeppL Replacement for the right end cap of our wall joint trim. The sketch is similar, the inner…
Print approx. €0.22–€0.27 excl. taxPreliminary estimate for PETGSource material: PET
I designed this things for you so please leave a like or a comment if you don't like something and i'll be very happy to se your makes so don't forget to post them. :) If you are looking for something more try to take a look at this:…
Print approx. €0.08–€0.10 excl. taxPreliminary estimate for one variant
Dies ist ein einfacher Fugenkratzer, den wir auf unserem Balkon benutzen. Der Griff ist angeschraubt, so dass man den Kratzer bei Abnutzung austauschen kann. Zusätzlich werden benötigt: 2 x Zylinderkopfschraube M4 x 18 mm 2 x…
Print approx. €0.53–€0.65 excl. taxPreliminary estimate for PETGSource material: PET
So I did this quick model to fit a 4mm square tube to a Stickybones Fly Rig socket and be able to use a normal winder. Printed in PETG vertically with the base towards the plate. No special settings, the fit will be super tight so be sure…
Print approx. €0.08–€0.10 excl. taxPreliminary estimate for PETGSource material: PET
A couple of years ago I broke part of a joint to an Outwell camping locker. I temporarily repaired it and now, thanks to a Prusa MK3S+ 3D printer and Fusion 360°, I've designed and printed a new one. I haven't installed it yet, it may be…
Print approx. €3.10–€3.79 excl. taxPreliminary estimate for PETGSource material: PET
Join balloon together for party etc….
Print approx. €0.21–€0.26 excl. taxPreliminary estimate for one variant
We have a dimmer switch that is now behind the mirror of our dresser. I designed this extension to enable us to control the lights without needing to squeeze our hand behind the mirror. All of the joints are print in place. Placements of…
Print approx. €4.90–€5.99 excl. taxPreliminary estimate for one variant
I think: 10% infill, 4-5 perimeters and 2mm top and bottom solid layer thickness can be enough, but you can try lower values for cheaper print, but result may brake in your situation (STL model is upsidedown)
Print approx. €8.16–€9.98 excl. taxPreliminary estimate for one variant
A modified model for a 2kg spool that doesn't hold together. And there are problems with it. There are two lengths. 110mm and 115mm. Usually 115mm fits, but sometimes it is necessary to use the shorter length 110mm. 2 pieces of sticks are…
Print approx. €0.56–€0.69 excl. taxPreliminary estimate for PETGSource material: PET
Quick and reliable prints for coupling two pieces of PTFE of either the same or different dimensions. Versions for 6mm or 4mm OD tube included. Requires 12x3mm magnets with 4mm interior hole and molded retainer clips. Non Printable Parts…
Print approx. €0.29–€0.36 excl. taxPreliminary estimate for one variant
HUGE UPDATE 9/13/2024: Dummy 13 v1.0 is now available! Check out the new and improved version of Dummy 13 here. This page will keep the previous beta files to ensure that no one's remixes are broken. Dummy 13 uses a CC BY 4.0 license!…
Lucky 13 is now on a CC BY 4.0 license! This means that you are free to share these files however you like, including selling prints, provided that you give proper attribution. You can give proper attribution by including this notice on…
Mini 13 is now on a CC BY 4.0 license! This means that you are free to share these files however you like, including selling prints, provided that you give proper attribution. You can give proper attribution by including this notice on…
About this model Say hello to Carbon 13, the latest generation of 3D printable action figures. Carbon 13 introduces a hybrid joint system that preserves the dynamic range of articulation you expect from the 13 series while freeing up…
I updated “the most articulated Snake ever!!!” that the segments can not be rotated complete 360 degree anymore and holding better together. I added a test file that you can check before, if your printer settings will work without…
Easy 13 is now on a CC BY 4.0 license! This means that you are free to share these files however you like, including selling prints, provided that you give proper attribution. You can give proper attribution by including this notice on…
About this model Say hello to Carbon 13, the latest generation of 3D printable action figures. Carbon 13 introduces a hybrid joint system that preserves the dynamic range of articulation you expect from the 13 series while freeing up…
Snap-fit ball joint with locking nut - Giunto Sferico ad incastro con ghiera di blocco Compact, reliable, and easy to assemble. The T-SSIC features a snap-fit spherical joint secured by a threaded locking collar (clamping ring). Ideal for…
This coupler allows you to join two ends of PTFE tubing together with magnets! This will be useful if you want to have an airtight connection between two PTFE tubes but still want to be able to pull/push the filament inside sometimes. I'm…
Use case: Once I had completed the slim 12mm lockable ball joint, I realized how super useful this kind of design is. While the lock is quite strong on the 12mm ball already, I figured there are probably use cases that require an even…
Introduction: Thanks @soozafone again for sharing the Dummy 13 to the community. It is a great framework/foundation for facilitating other creators. After fixing the chest and make it more organic, I think it is time to improve other…
Lighter and Cigarette or Joint Case Introducing BlazeGuard: the ultimate solution for discreetly storing your essentials with an added touch of satisfaction, now your ideal companion gadget for every picnic, barbecue, or tracking and…
My wife asked me to make a holder for the scrub daddy sponge and this is the result. It sits on the side of the sink with an outlet for the water This is a new design with print in place jointed legs, in the original the legs clipped on…
Check out the updated Joints+ for Version 1.0 of Dummy13. What did I change? I added a gap in each joint to allow for easier assembly and provide a longer-lasting grip. This is only for scaled-up versions of the Dummy13. The minimum Scale…
Universal Ball Joint. Inspired and modified according to Universal Ball Joint model by DieZopfe (https://www.thingiverse.com/thing:5020323) Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Filament: C-TECH…
Pocket Hole Woodjoining : tooling for drilling planks for assembly. mark template 2 for plank thickness. (10mm to 30mm) BOM : 1x Garabit 1 1x Gabarit 2 1x SCREW M5x20 STEEL 1x HEXAGON M5 2x drilling barrel 12mm diameter
Thanks for checking out my model! You'll find all the details, instructions, and recommended print settings below. If you enjoy my designs and would like to support my work, feel free to buy me a coffee . I'd really appreciate it! Happy…
This is a model I uploaded and strengthened the arms that are too thin at the bottom connection by raising the connecting bar and adding 2mm to the bottoms of the arms making them stronger and last longer. 15% infill Printed on Bambulab…
Now V2 - Faster Stronger Better LINK - To the file Model fixed to store normal size Joints and prevent the premature damage. The cap has a hole to be a keychain. You can also download our other models. 👇👇👇👇…
As small as I could go with functional, working ball joints. Fused the armor and frames together except for the interconnecting, moveable joints. 0.12mm layer 2 walls, 50% infill Auto tree support, build plate, critical Print time <45min…
My Website This is my custom-designed Dart camera setup with an integrated light ring. I printed the whole setup on a Bambu Lab A1. The problem with other setups is that I hit the camera on top when trying to throw a double 20. User…
Easy to print. No supports.Threaded cap. Not a flimsy tube.
PROJECT PRESENTATION I share with you the source files allowing you to make a solid ball and socket connection to reuse in your designs. This version is the result of a long series of iterations to find the right design. This ball joint…
The N-joints are a system for easily crafting solid and inexpensive structures and furniture using square wooden rods and 3D printed joints. The concept is similar to the "Jonction-P" by Samuel N. Bernier's, but here the wooden rods are…
This is essentially a re-make of https://www.printables.com/model/666609-ender-3-v3-se-ball-joint-filament-guide with a more reliable mounting option. As mentioned there, I really like the ball joint filament guide, it's fun and…
在 Cinema 4D 中设计了一条时尚可爱的铰链蛇！眼睛是为多色打印预设的。A1 @mini 用户可以缩小模型以便于打印。希望你会喜欢它！~
Print it and add O-Rings 15,8x3,1 Print Orientation with support for enforces only.
Drop-in replacement of original hip joint. I acquire this idea from Bandai HG Gunpla models, allow the two ball joints to move upward and downward independently. Significantly improve the mobility of legs. About the “improved” folder:…
I had issues printing the frame of Mini 13 with no supports, so I remixed it with some simple supports built in. Inspired by this for Lucky 13 by basti30 : https://www.printables.com/model/154760-lucky13-easy-print-without-brim Printed…
Different joint parts (simple, double, triple). You can do an infinity of variations with multi legs and arms from Dummy 13 and Lucky 13 … All is compatible with my wings design . Enjoy and hope to see your creations !
I designed this for my specific toolbox drawer (US General 44" top chest), and the specific pliers I own. It probably won't be perfect for you unless you happen to own exactly the same stuff. But I am sharing it anyways, because some…
Hi, I remade this model put with a print-in place hinge. I added my fusion 360 file which is parametric - meaning if the print in place is too tight, you can make it “lose” in the model. Look at the image referring to that (file: Filament…
This model is compatible with the lego system.
Ball Joint - Sferical snap fit connector - Giunto Sferico ad incastro 25x45x50mm SSIC 25x50x50mm SSICs 25xØ50mm SSICr Update: 21/03/2025 Added Model SSICs and SSICr Higher mechanical strenght 17/04/2026 Added SSI_ST Resize to adjust…
This is a replacement part for the Turtle Beach Stealth 700 Gen 2 headset. My headset is for Playstation, but it should work for any 700 gen 2. This was modeled for the left side of the headset, but I would think mirroring the model…
A simple Ball-joint for your use. V3 is the newest and most optimized model.
The source marked this model as adult content.
BOM: Printed with ROSA3D Starter PLA Red Expand your 3D-printed woodworking toolkit! Following our popular L-corner jig, this precise T-joint assembly jig is designed to help you flawlessly connect intersecting standard 18mm boards at a…
I a ball joint foxy (https://www.thingiverse.com/thing:1112196) but couldn't really find any of the other animatronics using ball joints (besides a "grim" foxy). So, I decide to make them. If you have found models of other animatronics I…
Scaled to 150% Parts joined by 1mm 1 or 2 layer height grid to hold in place while printing. I'm finding some of the armour pieces are a bit tight fitting at this scale and do break on assembly - especially with weaker PLA prints. Nothing…
This model is compatible with the lego system.
This model is compatible with the lego system.
This is a simple dovetail joint with a snap fit connector. It is handy for connecting two pieces together. It isn't very useful by itself (except to admire how cool it is). But you can integrate it into other models. I am going to use it…
This is a geometrically CORRECT Hirth joint. It includes SOURCE files and DOCUMENTATION. There are a lot of Hirth joints out there. Some are completely wrong, some are very close, but almost none of them are geometrically correct. If you…
There are 3 hip options included: Standard width flexible, wide flexible, and wide non-flexible. Shown in the photos is the wide flexible version.
A ball and socket joint with full Fusion 360 source. It's parametrized so the joint can be resized easily. It does use the standard thread tool so the thread size does need to be manually adjusted after changing the ball size. The default…
joint case with cap instolled print in place. cap fixed to main body in 1 file with no supports. Satisfying feeling with opening and closing the cap. recomend printing with brim, after cap is finished is possible to crank up the speed as…
A print in place based on the joint used in the LIMS2-AMBIDEX robot. https://youtube.com/shorts/Mo7VGDBU9nI The supports are baked in, so I would recommend not to scale down the model.
This model is compatible with the lego system.
