Entina Weedo Monoprice Tina 2 Cadet 1kg Spool Holder
1kg spool holder 1Kg spool holder large version https://www.buymeacoffee.com/teto121119u
- Downloads
- 1,835
- Likes
- 84
- Rating
- 4.83
277 models
1kg spool holder 1Kg spool holder large version https://www.buymeacoffee.com/teto121119u
I wanted to start using Orca for all my slicing needs so i made this Profile for my MPSM. It might not be great but i tested it with a few prints and it worked pretty good. I had no issues. unzip the file and import the config. Includes…
I found a model similar to this, but the fitment was poor, it could wiggle into direct contact with the heat-block because the clips were very misized for the geometry present.. So I remade my own from scratch, with as reasonably precise…
After struggling to find any kind of upgrades that can be done on this Monoprice MP10 printer (same as the MALYAN MA10), I designed and created my own V6 Hot-end adaptor. If you own one of these printers, this adaptor lets you KEEP the…
I printed the original model and liked it but it didn’t work for my regular sized 1 kg spools. I loaded the model into Tinker CAD and extended the arms out to make them long enough to support the spools I wanted to use. I needed this…
Monoprice Delta Mini V2 Orcaslicer Profile with build plate
I am lazy and I did not want to have to buy new screws, so I designed this handle for the MPSMv2. It might fit a V1? I'm not sure. Uses 3 of the stocks screws which hold the metal frame together. You can print without supports, or add a…
I have been able to quickly and easily calibrate my Monoprice Select Mini with this test pattern. The outer square is .5mm tall. The next tallest square is 1mm tall. The corner and center squares are 5mm tall. The screws holding the bed…
This is djeaton's Lithophane holder scaled down so as to be able to be printed on a MP Select Mini. Included are a read me file with the changes I had to make and a file about how I made my lithophanes. The corner posts fit very tightly…
Designed in OpenSCAD to test printing parameters The test piece is 30x30x110, with rounded corners Print instructions Unassociated tags: dimension test, dimensional test, monoprice mini delta, tower test Category: Robotics
Testing now. It works. Heating is a bit slow, but it stays steady once at the right temperature. I'd use a 30W heater to stay well below the 2A limit of the JST PH connector. This is a replacement X-carriage/hotend for the Flashforge…
I was after a filament guide for my Monoprice Select Mini v2 that I could run some Bowden/PTFE tubing to from a dry box. Drawing on m_power's and EdventureTime's filament guides, I designed this for use with a PC4-M6 pneumatic fitting.…
I wanted to do the well known NEMA-17 Z-axis mod (https://hackaday.io/project/14823-monoprice-select-mini-maximum-3d-printer-mods/log/55525-upgrade-the-z-axis-with-a-nema17-stepper-and-tr8x8-leadscrew) but for some reason I found my…
My goal is to print small ABS things without issue. Mini Delta for starters, later Delta pro. Feel free to print and enjoy as this project is complete and works on all 3 sides :D And hey, if you were blessed by this design wont you leave…
For using LJ12A3-4-Z/BX proximity sensor on the Monoprice MP10 (CR10-style) 3D Printer. The bed levelling sensor can be hard to find so if it fails this bracket can be printed that utilises the existing mount and m2.5 screws to adapt to…
Remixed to reinforce the neck and mount to make this filament guide stronger. I had two break on me. One while moving the printer, one when loading/unloading filament. This will require two M3 10mm or M3 12m screws as the base is thicker…
Autofill Adapter for Elegoo Jupiter Female thread to fit Monocure, MACK4D, Wanhao, Monoprice, eSun and probably other premium aluminum resin bottles. Male Thread to Elegoo/Anycubic/Prusa (old) brown resin bottle type. Double check your…
This is a model of the popular entry level MP Select Mini 3D printer Print Settings Printer Brand: LulzBot Printer: TAZ 5 Supports: Yes Notes: Rotate model 90 degrees on the Y axis to minimize supports Category: 3D Printers
remixed bed level of http://www.thingiverse.com/thing:1905398 Category: 3D Printing Tests
I have created this mount to connect a Webcam or Gopro to the Bed of my Monoprice Select Mini. This mount was designed to use the standard screws (no extra drilling necessary). Print instructions I printed the pice PLA and ironed the top…
This is an extruder upgrade for the Wanhao/Monoprice Duplicator i3 Mini (NOT FOR Monoprice Select Mini). This supports flex filaments as well as stronger feed of PLA and PETG (no slipping). This will get you a consistent extrusion. Note…
Bed align clip for Monoprice Mini Delta V2, to reduce z-wobble / rough surface / horizontal lines. A little fiddly to assemble but sturdy & easy to print. To be printed in ABS or PETG. (for flexibility and heat resistance) 0.4mm nozzle,…
This is a Prusa Mini-inspired MP Mini X-end idler block. It significantly improves the stability and alignment of the X axis, by clamping down on the rods as opposed to just using friction fit that's pressed on. My first layer calibration…
Filament spool extension for a Monoprice MP Voxel. unfortunately, the filament door dosen't fit on with extention.
Fixes an issue with some printers of this make having too much play in the Y axis rod, No need to strip the printer just slip over tha y axis rod then slide as far forward as possible, Printed in Petg but I have done them in PLA and the…
Remixed from https://www.thingiverse.com/thing:2006457 to sit on top of the printer, for minimal desktop footprint. The feed angle is probably pretty bad, but it seems to work nicely so far (I've also replaced the original axle with 608…
I know this is a niche product for an tiny obscure discontinued printer, but there's still a group of users out there that love them. You can still find them sold on the used market and under other names as well. They will run all day on…
The PTFE Bowden tube on my Monoprice MP10 (Creality CR-10 clone) wasn't well supported where it left the extruder. It drooped excessively which seemed to cause unwanted friction on the filament, so I designed this bracket to resolve the…
This is a remix of the no drill side for Monoprice Select Mini printers. I added more vent holes. I was going more for function than style so the holes go over the metal on the machine a little. I do not mind, and if you do not either,…
This is a long time project. I've had the MPMini for about 5 years now, it was my first introduction to 3D printing and it has a special place in my heart. I've upgraded it so many times, mostly due to my breaking the original hot end,…
Another extruder spinner for the Monoprice Select Mini. Snoopy as "The Flying Ace" from Peanuts.
Other hardware required: 6mm or SAE almost-equivalent bolt and nut. Using paxamime's excellent original dial indicator gauge mounts as a base I've modified them to fit a Harbor Freight or Chinese equivalent dial indicator gauge. It's one…
Remixed to fit my Monoprice Select Mini V2. Supports for the side-nubs are embedded in the model, you can either keep them or clip them off. The clips can hook around either way. Category: 3D Printer Parts
I designed this to fix an issue i have with my Audeze earpads being too large for the driver of my m1060 headphones. So i enlarged the front face, and added a retaining lip around the cup to prevent them from sliding off over time.…
This is just a remix on the great design here: https://www.thingiverse.com/thing:2000793 by by o13102 I just wanted a more cleaned up version that wouldnt require any supports and I removed the logo as it just adds time to the print that…
This is a remix of https://www.thingiverse.com/thing:2750908 originally made by parhamdb . It also uses the mounting tabs from https://www.thingiverse.com/thing:1686028 by mmoore0 . Before I got a Prusa printer, I had a Monoprice Maker…
A modified Z stop holder so the homing height could quickly and accurately be adjusted independant of the bed levelling screws. This was in preparation for fitting a thicker bed. I reverse engineered the part from a very close to fitting…
Foot for Monoprice Cadet/WEEDO Tina2
I took mediaman's excellent filament guide , trimmed most of it off, and rotated the stem, to fit on jwnicholson's cover . I simply glued it on using Gorilla super glue. I tried to come up with a way to integrate it into the cover but…
These are parts to convert your Monoprice Mini Delta to have a Bigtreetech SKR mini E3 mainboard and TFT35 touch screen. It also contains parts to covert your printer to house lipo batteries and be completely portable. Many details below…
A small tool holder for one screw of the Monoprice Select Mini. This holder can hold an allen key of about 5cm and a plier or anything else. The picture shows the 1st version which was to short. So the allen key bumped onto the pin. I…
I designed this part to improve filament cooling of the MPSMV2 with a Single 40mm Fan. Works quite good so far, the screws I used were M3x16.
My Monoprice MP10 (Creality CR-10 clone) fitted with an alloy MK8 Bowden Extruder upgrade would turn any soft filament into spaghetti due to the filament path floating in mid air after passing the extruder feeding gear. I designed this…
This is a model of the Monoprice Mini Delta Print Settings Printer Brand: LulzBot Printer: TAZ 5 Supports: Doesn't Matter Notes: rotate model 180 degrees to minimize supports Category: 3D Printers
I mad this wheel to guide filament if the spool is set up on the control box instead of on top.
The idea of this mod is to isolate already weak bed heater of the Monoprice Mini Delta V2 to prevent cool air suctioned by the electronics cooling fan entering underneath and cooling the bed plate. This is two piece component, to install…
Replaced the mainboard with a different one and used the Mini12864 display for the project. There are two versions of the display. The Fysetc one has a longer reset button, and this one is designed for that one. If you use the BTT version…
Remixed the Design from TeachingTech. Thanks for this incredible design and for sharing it. Here is the link to my remixed Version on onshape:…
The Cable Chains on the MP Maker Select V2 are not being properly utilized in factory form. Chains need to be constrained, so that they ‘unroll’ gradually across their motion, to spread cable flex out along its length and extend lifetime.…
Printed with a Monoprice Select Mini. To securely mount the powerbrick. Mounts are slightly less tall then the powerbrick so the rubber feet grip on the surface you mount it on. Timelapse: https://www.youtube.com/watch?v=-HWKaUpa6VQ Edit:…
Feet, for the mpsm.
I wanted a minimal spinner for my Monoprice Select Mini V2 because I'm really not into all these OTT designs. This is a "boring man's" no-thrills functional spinner. It's not the most snug fit because I know different PLAs shrink at…
I recently purchased this Mk8 extruder for my Mini v2. This Mk8 extruder is recommended for the Creality printers but I figured I'd give it a shot since it should be better for printing flexibles. Unfortunately, when I went to assemble it…
Raised the top edge for better alignment with original retaining clips Beefed up clip attachment points Printed with tree supports on Cura.
Remixed to reinforce the neck and mount to make this filament guide stronger. I had two break on me. One while moving the printer, one when loading/unloading filament. This will require two M3 10mm or M3 12m screws as the base is thicker…
PTFE Tube cutter use a Razor blade and use slot 1 and 2 like a pencil sharpener Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 25 Category: 3D Printer Parts
This is a remix of Toys spool holder for the Monoprice MP Select Mini. I love the spool holder and have been using it for a while but I noticed that the spools rub on the mounting bracket and the spools sit off center of the spindle as…
This is yet another filament spool holder for the Wanhao D6 with bearings. This will hold standard 1KG spools and 3.5 KG spools that measure 12" x 4". The designs I tried didn't work with my cheap 608 bearings as putting pressure from…
This is one of my older designs I did a few years ago. It still gets quite a few hits on Thingiverse and I figured it might help a few people here. UPDATE 2: Wow! Been awhile and I'm glad to see my files have helped a few people. I have…
Springy Fan bracket for MPMD V2. I bought new fans (Sunon MF40101V2-1000U-A99 for inside and MF30101v2-1000U-A99 for hot end) for my MPMD v2 but the internal one was still making a lot of noise, figured out it was making the plate it was…
I had trouble keeping track of the tools for my new Monoprice Delta Mini v2, so I designed this organizer to hold them all. It prints in under 40 minutes and keeps everything neat! Simply snap it onto one of the pillars and adjust the…
This side panel fits the Monoprice Select Mini v2 with the SKR 1.4 Turbo board and this board mount.
This is a quick re-mix of kapakahi's MP Mini X-Axis Limit Switch Bracket to allow it to mount on the MPSM V2 Z Carriage by muzzled. STL and CAD files are included. Print Settings Printer: Voron Rafts: No Supports: Yes Resolution: 0.2…
I was jealous that other 3D printer users had their own filament sensor accessories, and I thought it was about time for a Monoprice Select Mini user to have make it happen! So I ordered a Makerbot 1.2 style endstop from China ^^,…
I wanted to save some filament and time to print, so I hollowed out the filament holder but kept the strength to carry the weight of a full roll. Print with 3 walls and 5 top and bottom layers. TinkerCAD file:…
This mod allows you to have the filament roll on top of the printer instead of hanging off the side, lowering the footprint of the printer to the machine dimensions as it should have been from the beginning. Just unscrew the handle and…
Updated Design 2022 The X-Axis Gantry on the Maker Select can be a little wobbly, since the span consists of only the 2 x-rods, with their ends only held in by 1 set screw each. This Brace uses a threaded rod to help stiffen things.…
I recently replaced an aging Magni V1 in my entertainment center listening set up with a Liquid Spark Headphone Amp (the font-mounted power switch is a huge blessing…) but I wanted to have the amp standing up next to my center channel…
I finally came across some filaments that were so rough that they weren't pulled efficiently through the filament sensor and the PTFE tube to the extruder from the back (Fluorescent PLA and wood filaments). Re-purposed some designs to…
I know its tedious, but if you have a delta pro do this as your first print, itl save you some headaches. 270mm covers the whole bed so print with no support whatsoever. Category: 3D Printing
This is an E3D Hotend Mount for the MPSM V1, it probably works with the V2 but I don't have one. There are two hotend mounts, one that has a DF 5015 Radial Fan, and one that doesn't. There are two clips on the left side of the mount, one…
Replacement knob for Monoprice Mini. Has indentation for finger so you can spin it much easier. Print Settings Printer Brand: Monoprice Printer: Maker Select Plus Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 30% Category: 3D…
My, not so pretty but will do the job, version of a ring blower that, if my measurements are correct, fit the original hot end of my Malyan M320 good. If I am correct it should also fit the M200 and the Monoprice v2 as well. Also made an…
Cool your PCB stepper drivers with a 30mm fan. Includes nut traps for easy fan swaps.
This design pairs well with my accessories organizer ( https://www.printables.com/model/214432-accessory-organizer-for-monoprice-delta-mini ) if you want to keep all the easy-to-lose tools accounted for. No supports required, just…
This is a profile to hang this RPi4 Case https://www.thingiverse.com/thing:3714695 on an Monoprice Select Mini. scad Source is here https://github.com/andimoto/rpi4case\_holder\_MPSMv2.git Have fun!! Print instructions Category: 3D…
Blower duct for a Volcano hotend for the MalyanM320/Monoprice select mini v2
These feet eliminate vibrations transferred from your printer to the work bench/table, cutting down on noise without needing to buy a paver and a foam pad. Printed with no supports at 0.2mm layer height in PLA. You will need print 2 as…
Unfortunately, this mount is too big to print in one piece on the Mini itself as the panel is 160mm wide. I have a larger printer, but you may need to cut the model and assemble it after printing. The source CAD can be found at the link…
I got sick of ferrying the micro SD card back and forth and having to keep track of the micro SD card adapter between prints so I designed this bracket to hold a micro SD card extender adapter cable https://amzn.to/3heRM3W Print Settings…
The fan shroud is designed to be a drop in replacement for the existing shroud on the monoprice mini delta v1 I believe it also works for the v2 would love someone to confirm. It allows a 4010 fan to be used for part cooling. I printed…
After getting my filament jammed with other filament guide, I decided to design my own filament guide. Print instructions Category: 3D Printer Accessories
This is a mod that makes the Monoprice Select Mini V3 leveling manual. This gives you the ability to make adjustments to the bed to make it print perfect first layers. I got a V3 about a year ago and no matter what I tried, I could not…
I moved my Monoprice Mini Delta V2 over to klipper but missed having a screen. The original screen is a 2.8in touch display, so in comes the CYD Klipper 2.8 in display! Full credit to CYD Klipper project for its awesome firmware on the…
This is a drop in replacement spool holder for MP Mini printers. It fits most standard 1kg spools.
This was designed for a Monoprice Mini Delta. I had individual filters on each spool of filament I used and thought attaching one to the printer would be more efficient. I also wanted to use a filament guide to ensure the filament entered…
Warning: The cover is as of yet untested. Tell me in the comments if it needs adjusted. This is a drop-in replacement for the MP Select Mini's extruder arm and cover. After mine broke the day after my printer was delivered, I found…
A bracket to alleviate the stresses found at the extremes of the build volume that put pressure on the Bowden tube connectors causing shortened life of the part. No Supports needed. Print in Draft 0.2625 is still strong at 15% infill but…
My first printer only accommodated filament spools with a large hole in them, and I wanted to use some small half-kilo roles, so designed this as the solution. The first Monoprice Select Mini was a cheap yet capable 3D printer, with…
This is a remix of the great work of several gentlemen before me. This version is specific to the slightly different gap size found on the MP Select Mini V2 vs. the V1 unit, owing primarily to a nut of a narrower width, resulting in a…
A simple strap mount for the Monoprice Amp/DAC. It's designed for #7-3/4" screws. The Fusion 360 file should be parameterized fairly well for adjustments for different screws, or really, any type of rectangular thing you want to mount.…
Monoprice Delta Mini Filament Guide
A 2 in 1 fan duct for the nice Monoprice Select Mini GT2 Carriage for E3Dv6 Style Nozzle mod. https://www.thingiverse.com/thing:2353376 I couldn't get the proper cad files or a .step file for the original mod so it may look a bit ruff…
This is a simple side mount for a Raspberry Pi v2.1 camera module with a Monoprice Mini Select v2. I could not find an existing design that I liked, so I designed a simple side mount and remixed parts from several designs to: avoid…
I adjusted the bolt and nut to fit the factory mount on my Monoprice. Helps with the more sustainable paper/cardboard filament spools as manufacturers move away from plastic and it also puts less strain on your extruder. Credit to…
By following the instructions in the video, these parts will allow you to use your BLtouch with: Auto levelling at the start of each print in only 30 seconds Accurate/symmetrical spacing of probing points Automatic adjustment for any…
This is a remix of the MPSM E3D V2 Mount GT2 Belt 40mm fan 3d touch by e36ltw with several modifications and additions. I found that on my Monoprice Mini Select v2, the original by e36ltw had the BLTouch / 3D Touch mount too far back,…
After I printed out Monoprice Select Mini SD Card Extender Holder-mod ( https://www.thingiverse.com/thing:2357466 ) I soon realized I had bought a MicroSD extender not SD LOL So I made this adapter since I had already printed out the SD…
This is a very basic remix to change the extruder hole to a round 5mm from the keyed hole on the Creality extruder. I used tree supports with Cura and that worked well, with a support blocker on the antenna.
This is a work in progress (V1 untested) 15-April-2019 Corrected some missing levels icons of the TFT and added an emergency Stop in the custom menu to use when working with Octoprint. 3-April-2019 Move the MKS Main Board up to 4.2mm so…