125mm (5") sandpaper storage
Ready for MMU. Print the partitions on their side with 0 top and bottom layers. I used honeycomb infill.
- Downloads
- 2,523
- Likes
- 1,060
- Rating
- 4.71
272 models
Ready for MMU. Print the partitions on their side with 0 top and bottom layers. I used honeycomb infill.
I liked my earlier design, but found it tricky to extract individual discs sometimes. This design removes that issue as it uses removable “drawers”. The drawers are held in place with 10Øx3mm magnets though these aren't entirely…
I printed with 40% infill ABS for better structural rigidity and heat resistance.
I liked the idea of this design …but I wanted one with wider and more more slots and would not require supports to print. So, I created this design which has 8 slots to fit standard 5-inch/127mm sanding discs. I made the walls have…
This model comprises three parts, easy to print without supports. Assembly requires an M3 screw and nut. Assembly instructions: 1. Print the parts (suggested: lower layer height for smaller pieces) 2. Insert the nut into the hole and the…
I designed this to hold 5 different grits of sandpaper for my 5" random orbital sander. Each one is labelled for easy identification. I can customize it if you have different grits, just let me know. Also has two holes in the rear for…
Printed with PLA. There is a thicker Version with 2mm Wall thickness. The original has 1,5mm Wall thickness with prints much faster.
Sanding paper holder for eccentric grinder 125mm Mounting is by means of two screw holes. Print Settings Rafts: No Supports: No Infill: 20% Filament: PLA or whatever…
125mm & 150 mm sandpaper holder with floating dividers for easier organisation in the workshop. The Cradle is not my design I have remixed it a bit for my needs. I added the dividers since the use for me depens on the type of job I do. So…
***If you like what you see please give a “Like” and a “Follow”! The goal is to get over 200 followers!*** This is the first in a series of sandpaper holders. This is the medium size that is designed to hold a piece of sandpaper that is…
A 3x3x3 stackable gridfinity tray designed to store 125mm/5" sanding pads, with a notch to make easy grabbing it with your finger. With 3 units tall it holds between 10 and 20 sanding pads depending on the grit (the coarser the grid, the…
Self tensioning and clamping in one, no Winkles, always smooth For short stick, cut the sandpaper to a length of 230 mm and a width of 12 mm For long stick cut the sandpaper to a length of 280 mm and a width of 12 mm Also goes as a nail…
Gridfinity size 3x3 is 126mm so had to remove the walls to make it fit and not waste space. Update 221005 Minor tweak to measurments Added proper size files
Update 29 jul 2022: Made the hole in the stone holder bigger so that the stick attaches easier. Prerequisites: To 10 mm M5 screws with two hex nuts Print with 2 mm walls/top/bottom for stability and with no support. 150_5_20.3mf: For…
Hobby tools: sandpaper holder (different sizes), seam sander
Very practical sandpaper holder. If the sandpaper is used up, the sanding belt can simply be moved a few centimeters. The sandpaper belt holder consists of 3 printed components: Block Tensioner Eccentric Other accessories: Cylindrical pin…
V2 | Remodeled This tray has been made for more efficiency during sanding. This tray is for sanders with a ⌀ of 125mm with 8 hols. If you've suggestions or feedback, please let me know or comment below.
5 inch Round Sandpaper Holder. I upload the following grits: 40, 60, 80, 100, 120, 150, 180, 220, 240, 320, 400, 500, 600, 800, 1K, 1200, 1500, 2K, 5K and blank. If you need other grits let me know and I'll upload them. 2021-02-16 -…
Gridfinity holder for sandpaper for an orbital sander (⌀: 125mm)
I wanted a way to store my 5 inch orbital sandpaper discs but all the designs I kept finding use too much filament. Some are good but this one is even simpler. A 5 opening holder will use about 150gram of filament which is a fraction of a…
5 inches sandpaper drawer storage. 12 drawer version and 6 drawer version available. It can be wall-mounted. This is my first design. I was looking for something like this but found nothing, so I designed one. Hope you like it. I made the…
I designed this sandpaper caddy to be wall mounted with screws by default. If you have a Wall Control system, then I've also included an adapter pin that makes it compatible with that as well. The label slug can be customized with text in…
UPDATE: Make sure to use "5 inch sandpaper storage box 8 FIXED.stl" and not "5 inch sandpaper storage box 8 drawer less material.stl". I corrected the height of the one drawer that was 1mm too small. Or use the original box (with less…
🟨 Material: Prusament Mango Yellow PETG it looks like a 🐝 DeWALT yellow ⬛️ Layer: 0.3 is enough
Sandpaper holders for festool 150mm sandpaper disks. Designed to be more easily lifted vertically, and for holders to be labelled from the top, making them identifiable by looking straight down.
Ich habe hier einen Schleifpapierhalter für meine Baustelle konstruiert. Die obere Klemmplatte besitzt Noppen, welche sich durch das Schleifpapier bohren, welche den halt nochmals verbessern. Die Schrauben habe ich als Rändelschrauben…
This tray neatly stores and organizes 80mm triangluar sanding pads used by typical oscillating tools. Can be printed horizontally or vertically with decent bridging.
I bought a multi-pack of sandpaper and I wanted a good way to store it that allowed me to easily access the sandpaper I wanted. So I came up with this layered offset design, and it's worked well for me. The separate layers make it easy to…
A 4x4 gridfinity bin for holding 150mm sandpaper. My bin holds 5 grits of sandpaper, with trays with tabs to lift up the stack to reach the desired grit. A separate lid on top holds a smaller stash of sandpaper that is currently in use.…
Simple wall holder for 125mm pads. Each section accomodate around 50-100 sheets. Print Settings Printer: vking Rafts: No Supports: No Resolution: 0.25 Infill: 10% Category: DIY
Update: Uploaded a new model of the 2.25 sander as well as new 1.125 sander. New models facilitate easier printing. A sanding block that perfectly fits a 1/8 sheet of 9x11in sand paper. Tear the sand paper sheet in half the short ways.…
Two M3 x 25 screws and nuts for the hinge. Four 5mm x 3mm magnets glued in place to keep it closed. It should print well without supports. I have added the Fusion 360 file for those that may want to tinker with the design. I'm not much of…
If you have a Milwaukee M12 FUEL Orbital Detail sander 2531-20, and wanted a good place to store your sandpaper, this it. I printed this with PETG on my Prusa Mini, and put it right next to my sander. Looks decent enough, and holds plenty…
This is a template I made and printed to make cutting strips of sandpaper easier for these sanding sticks https://www.prusaprinters.org/prints/22236-customized-sanding-sticks-with-labels Height is 3mm but you can adjust the Z up or down…
I created a sanding block for the 50mm wide sanding paper I have. You'll need a M6 hex nut + a 15mm-ish M6 bolt.
Summary This sandpaper tower is ideal for keeping you sandpaper organized and most importantly, free from dust! Ideal when you don't care about wood dust management ;) There is a collection you can download from or you can download the…
I was not willing to spend money on a sanding block, so I designed this two-piece construction. For my purposes, it works great. For clamping you need 2 x M5 screws and also 2x M5 wing nuts. Print Settings Printer: Artillery Genius Rafts:…
I wanted a tiny sanding block to keep in my tool belt for carpentry work. This is not designed for lots of sanding work, simply to quickly tidy up a cut edge on a cladding sheet or similar application prior to installation. For instance,…
I created this sandpaper holder for my Gridfinity system. It needs 4x3 modules and has 10 slots each having a width of 12,4mm. Each slot can store roughly 10 pieces of sandpaper (e.g. Bosch C470). I guess it is also perfectly fine storing…
Designed to fit Porter Cable and Black and Decker Type 340/341 series sanders. Confirmed fit for: Dewalt DW411 Type 2. COULD ALSO POSSIBLY BE COMPATIBLE WITH: DeWalt: DW411 Type 1 Palm Sander DW411 Type 3 Palm Sander DW412 Type 2 Orbital…
Inspired by DisKeeper, but designed from the ground up to be a bit a bit taller and have a more robust french cleat. 125mm (5") and a 150mm (6") holders. Designed to use 2x (each) M2x12mm self-tapping hex screws to connect the cleats to…
Sandpaper holder or template. For fixing sandpaper for better handling during grinding. The sandpaper is pushed in and fixed with an inner wedge. The subject consists of two parts in the photo.
Leviga meglio e con meno sforzo grazie al SandPaper Holder , il supporto pratico per fissare la carta abrasiva. Il design ergonomico garantisce una presa salda e confortevole, mentre il sistema di bloccaggio mantiene la carta ben tesa e…
Fixed and remixed original model to remove the Gridfinity connectors on the bottom and adjust the dimensions to comfortably fit my 5.5" x 4.5" (~140mm x ~114mm) sandpaper in 10 different grits. Tray is 80mm high, 140mm long, and 130mm…
Oscillating Triangle Sandpaper Holder: This is a remix of a design I found on Thingiverse. However, I completely redrew it and added the following: Increased wall thickness/rigidity from 1mm to 3mm Made stackable with posts on lid and…
French Cleat Sandpaper Storage for 5inch random orbit sanders with dividers and positioner for quickly mounting sandpaper onto the sander base. F3D file is included and fully parametric. 3/4inch french cleat attaches to the main body with…
Holds about 10 regular disks per grit easily. I store it on its back for accessibility, which can cause the sandpaper to to catch on its neighboring grit. As a result I store my sandpaper alternating per grit( hook to hook and loop to…
Storage for 150cm sanding disks. Sorted by grit size. Print the sizes required, plus a top and bottom. They will click fit together, I added a blob of CA to ensure they didn't seperate. Attach to wall, or stand on shelf.
Little Helper to fixate the sanding paper on a BOSCH GEX150/125. Will also work with other models of BOSCH 150mm orbital sander Print instructions Unassociated tags: GEX150/125 Category: Machine Tools Print Settings Resolution: 0,2…
Mini sanding block for sandpaper. It is always useful when you need to sand the material gently and precisely. Junk paper? Replace it or print more blocks and have different grains on hand.
A tray to hold 80mm triangle sandpaper for oscillating tools. This version is remixed to 100mm in length for smaller collections. Included the divider tags for convivence though they have not been altered from original.
I printed this in PETG as that was all I had. PLA should be fine as well. It is a long 17 hour print.
I reworked the model benoitmeunier so that it would fit the project Honeycomb storage wall and to accommodate 90mm sheets of paper. I have attached a blank label to add gradation and a set of labels for multicolor printing without MMU. To…
I purchased sandpaper in sheets of 9 x 3.6 inches and soon discovered I didn't have a suitable box to store and keep them organized. So, I threw this together. I decided to add labels identifying the grit instead of printing the numbers…
This his a Skadis holder for Abranet Sandpaper. Sandpaper usually use with mirka Deros 150mm. It permit a good holding = 156mm ! The Sandpaper 150 mm are too short for these types of sandpaper. With hex pattern we use less filament 70g…
Three variants based on how much you would like to store (3U, 6U, or 9U). Photo shown is a 3U. Model also includes finger cutouts to easily remove units as needed.
Small sandpaper holder sized 42 x 22 x 10 mm. Perfect to be used when building e.g. models etc.
This is a remix of the drawers for the storage unit designed by Mgotier . The grid alignment system has been removed from the bottom allowing for a deeper cavity. Using a 0.4mm nozzle and the 0.3mm DRAFT setting in PursaSlicer this also…
This holder is designed for finishing 3D prints, woodworking projects, and various other manual tasks. Assembly requires an M5 screw and nut, along with a strip of sandpaper (any grit) measuring 3 cm in width and approximately 26 cm in…
filament: PLA height layer: 0.2 speed: 120mm/s
Compatible with festool sandpaper holder. Works with standard 125mm sandpaper
I know there are many other bins for sanding papers. However, I couldn't find one that is customizable. Compared to most others, this one does not require supports, perfectly stackable and fully customizable, including size (5'', 6'' or…
Sometimes it can be hard to line up the holes of your sandpaper taco with the ones in the sander. This tool can help you a little bit. It was made for the Festool ETS EC 150. It could work for other sanders too I guess. I used a resin…
This is an adapter for holding sandpaper with an oscillating multitool. I designed it for a DeWalt DCS356, but it may fit other brands/models with the same blade interface. The Everclamp grid with sqwasher plate and thumbscrews lets you…
This was designed to evenly divide a drawer in my sanding cart, but should be able to be resized to be slightly more space efficient. The grit label text can be changed in Bambu Studio.
Sandpaper organizer (diameter 50 mm) that can be screwed to the wall
Sand paper dispenser. Ive made this for my work van. Rips paper off nicely. Printed in PETG, 0.28, 25% infill. For personal use or for printing for family and friends. Not for retail. Print Settings Printer Brand: Creality Printer: Ender…
This is an organizer I made for my 3 2/3" x 9" sanding strips. I have added a bunch of little tabs for grit that can be printed and used for organization. I included all of the base files too so you can change any of the grit levels and…
Organize Sandpaper in your Gridfinity Storage shelf/drawer
A sanding block that uses 5 in sandpaper discs. It uses strips (or maybe a bunch of dots) of hook velcro on the bottom. You can use more on the sides, but you don't have to. There is another version with depressions on the sides, but I…
A practical sandpaper holder for your workshop. Multi Threaded screw, only needs a half turn to screw off Practical keyhole to hang to a screw or similar ONE TWO CUT Then attach the sandpaper, press down with the top and attach the screw!
A simple holder for sandpaper 125mm diameter. Print Settings Rafts: No Supports: No Resolution: 0.2mm Infill: 20% Filament: PLA Notes: Print with a 0.4mm nozzle at 0.45mm line width.
This is a simple grip/holder for regular 5" circular sandpaper pads. Just apply two strips of the hook part of Velcro (or similar), and optional some strips on the sides, and you are good to go. I printed it in Overture PLA+ with 0.2mm…
you need to get piece of sandpaper and also screw that is long 24 mm (measured from under the head to the end). The diameter of the screw is 5 mm. The sandpaper is long 28 cm and its 4 cm wide. THE STICK THAT IS IN THE MODEL IS NOT…
I wanted to get my sandpaper for my Festool RTSC-400 up on the wall within easy reach. I designed it to hold the three main grits that I use with this sander - 80, 120, 180. This is for the 80mm x 133mm sheets of sandpaper. Goes well with…
This holder is for abrasive cloth rolls which are up to 25mm wide and 200mm diameter (in the US, this is a 1" x 50 yard roll). The design can be extended to hold a large number of shop rolls. The design includes screw mounting holes in…
Einfache Lagermöglichkeit für Schleifgitter/-papier. Auf die kleine Ausbuchtung oben kann man, wenn nötig, noch die Körnung draufschreiben.
There are two holes inside for possible wall mounting. The dividers should slide in with a slight resistance. This may depend on the printer calibration. If necessary, apply a drop of glue to prevent movement.
If you have a lot of different sandpaper discs for a 150mm (6 inches) orbital machine. You can print this organizer and store the discs conveniently. The lower bottom of the holder contains segments that help you keep different types of…
Organizer for sandpaper (50 mm Diameter) pluggable
Allows mounting for the installation of a sandpaper disc
A hardback for rotary tool paper sanding disks, turn your rotary tool into a sanding wheel. *3m screw and nut needed* Printing: * No support needed* Infill: 10%+ Wall count: 3
This model was is a remeix of the model of @JG3Dcreations who remixed @RalfHorhager. This model uses, as the version it was remixed from, a M6x30 hex bold and one M6 nut. Prints without support material. Layerhight should be 0.2mm, for…
All print orientation are shown in the photo, and the Main Body have a "build-in support", don't move the support. --Print Setting-- Layer height = 2mm Wall = 2 layers Top & Bottom layer = 5 layers Infill = 15-20% Support = ON
Alignment jig for attaching sandpaper to 5" (possibly other sizes of Orbital Sanders) to properly line up the dust collect holes for optimal dust evacuation. Design in TinkerCAD. Printed at 0.2mm layer height with 20% gyroid infill.…
I order a box of mixed sandpaper rolls, but I wanted to mount it in my IKEA Skadis board. searching online I found supergimp design that fits my needed. I modified it a little and now it fits nicely less the paper box.
Gridfinity sandpaper rack for workshop organization. Holds sheets vertically for easy grit access and clean storage. The support allows to store the sandpaper of the model that can be found in this link , also allows to store a Clipper…
Sandpaper roll holder and dispenser to fit commonly available short rolls of sandpaper
Stack the grits you need on one side, finest at the bottom, then as you use them move them to the other side. Print flat side down, any filament, infill about 15%, 3 perimeters is better than 2. If you don't want them this tall, just…
This is a design to help organize and store 5 inch sanding disks in your workshop. The grooves are cut with a standard table saw blade width. Depth of the groove should be slightly deeper then 1/8th of an inch. I recommend the spacing of…
I bought a box of sandpaper rolls from Aliexpress, but paperbox had been destroyed during shipping. Modelled this one to keep them organized, I kept the center roll, and the endcaps from the original packaging. I guess at some point I…
Just a little holder/container box I use for storing sandpaper in my workshop. Prints perfectly fine in 0.2 without any supports (Bottom to Top). Use it for whatever you need to store in your workshop. There are 4mm screwholes to attach…
V3 | Remodeled This tray has been made for more efficiency during sanding. This tray is for sandpaper with 8 holes, and one with 4 holes. Added three new trays for smoother sandpaper. Stack 8 deep trays with a slim blank tray on top or…
This is the second in a series of sandpaper holders. This is the Large size that is designed to hold a piece of sandpaper that is 9"x3.6" (approximately 228.6 mm by 92 mm). The top can either be the larger top that is included with this…
A handy sandpaper handle (pun intended), especially dimensioned for optimal use of 23 x 28 cm sandpaper sheets. Cut each 23x28cm sheet into four 23x7 stripes, and secure a stripe with butterfly nuts on each side. Base size: 20 x 7 cm.…
Needed something to hold my different grits of sand paper for the phenomenally great M12 Detail Sander. This version holds up to 5 different papers or 4 and your extra tool pads. I printed with 0.2 layer height and did a color change at…
A modular system for easy and accessible storage of sanding paper It comes as individual pockets that clip together so you can print as many as you want to fit your needs. regular version can hold ~15 papers Large will hold ~25 If you…
Remixed from Gridfinity Bin_DividerEdition_3x3x7_1x6 Made it into a Gridfinity Bin_DividerEdition_3x3x7_1x12 Added more slots , making it 12 slot for my sandpaper
Simple sandpaper holder design made for a tolerance o 0.1mm to hold 1/8 of a 230*280mm sandpaper.
With thuis modell, you can organize your sandpaper. The modell is for sandpaper with a diameter of 125mm and it is stackable. I would print it with supports on the heetbed.