Sonoff Mini R4 DIN rail mount
Sonoff Mini R4 DIN rail mount. There are two versions, one for a single and the other one for two relays.
- Downloads
- 1,283
- Likes
- 102
- Rating
- 4.67
763 models
Sonoff Mini R4 DIN rail mount. There are two versions, one for a single and the other one for two relays.
This is a simple wall mount for the Sonoff Zigbee 3.0 USB Dongle. It is mounted on the wall using 4mm screws. It fits with almost any antenna you want to use because the included antenna is pretty bad. Be careful when removing the support…
Wall holder for the Sonos Move 1 & 2 speaker. Optional plug for the lower holes for hiding the screws. Screw holes are 4mm. Print it standing up (maybe with brim), no supports needed.
A Case for the Sonoff mini which clicks into DIN Rails (Hutschienen)
Simple wall mounts for the Sonoff Zigbee 3.0 USB Dongle Plus and Plus-E. For use with home automation gear. Prints solid. Back side down. No supports. Dongle slides in from the end. lul.. Has space for a USB extension cable. Can be…
Wall mount for Sonoff Zigbee 3.0 USB Dongle Plus. I would advice printing regular version. With USB connected Dongle won't fall out even if there are some play. Printed it in PETG and PLA. PETG works great with regular version, but there…
We designed this print with screw holes for the hooks, such that the mounting screws hold the mount together. This means that the design does not need to be glued together. If you would like to buy the Sonos One Wall Mount , you can check…
No supports required, print parts as oriented.
A Case for the Sonoff ZBmini which clicks into DIN Rails (Hutschienen)
The enclosure for Sonoff NSPanel Pro with IEC C8 AC socket for convenience remove the mainline or for optional inline AC switch. The enclosure is designed with minimum overhang for print without support. The screen angle is 45 degrees. 🚀✨…
It's better printed vertically, with the flat side facing the bed. Insert dongle from the open side with aerial facing the flat side.
I was using the cheapest PLA on the planet because you will not see the holders behind the speaker. But I'm pretty sure the print quality can be improved with better filament and maybe supports (haven't tested). CAUTION! Definitely print…
Vertical wall mount for Sonos Roam
Large and small holder for NSpanel PRO Sonoff
Here I designed a Wall mount for the new Sonos Era 100 speaker. It is able to tilt it downwards and you can rotate it freely. There are 2 channels for the cable. Screw the Holder with 2 x M4,5 Wood screws to the wall, then mount the…
Adapterplatte für die Installation des Sonoff NSPanel Pro 120 PW auf Standard 68mm Unterputz Installationsdosen mit 60mm Geräteschrauben abstand. Der Adapter funktioniert sowohl für die horizontale wie auch vertikale Montage. Eine leicht…
I recommend PETG due to the heat. I initially printed in PLA but the heat from the amp eventually deformed the PLA one so you may want to use PETG or some other higher temperature filament.
Wall support for Sonos Era 100 speaker. The speaker orientation will be perpendicular to the wall (it's not exactly round, so you can not rotate it). It requires 3 screws in the wall (check images for hole-distances) plus one M5 screw for…
Enclosure for a Sonoff NSPanel Pro 120 . Couldnt find one online so i made one in fusion . Used some heat inserts for the plate mounting
A small extension to the original model to make it wall mountable with support for 3 screws. I tried command strips but the speaker was too heavy(and concentrated) so drilling works better. There is room for the power cable to be…
I remixed Ruffle's design (thanks!) into a box for my Sonoff M5 EU (86mm, I live in France). This is a temporary housing (use at your own risk) to power it with 220V, and use it as a remote without batteries, for 2 other M5s that are…
Compatible with the White & Grey original Sonos Connect:Amp. Doesn't work with the newer Black Sonos Amps. Specifically designed for stacking multiple amps close together. Featured in this LinusTechTips video: Also included is our model…
Cable hole is on the right side, but if you need to have in on the left, just mirror the object in your slicer before printing.
Sonos one Gen 1+2 Corner wall mount. Print in PLA with 4-5 walls, 30% infil. with a 0.2 mm layer height.
I printed my model in PLA with 25% infill. Support is required. The stand is stable and has a tight fit.
This pogo-pin clip is designed to facilitate the reprogramming of the Sonoff S31 module without the need for soldering to the pads on the circuit board. The pogo-pins I used are 0.68 mm in diameter and 16 mm in length. The holes needed to…
Currently all pre-made wall mounts are sold out. So I tried to make my own. 40mm clearance from back of speaker to wall (sonos recommends minimum 25mm) Embedded steel bracket (90x90x40x3 mm). As the speakers are placed above the heads of…
Small holder to mount your Sonoff zigbee brindge on wall or another place. It is possible to use some of the prepared holes having a diameter of 2 mm for mounting. The second option is, for example, the use of double-sided adhesive tape…
The 3D printed mount is designed to perfectly fit the Sonoff SNZB-03 Zigbee motion sensor, ensuring a snug and secure fit. Whether you prefer a more permanent installation with screws or a flexible and removable option with magnets, this…
Hello, just another enclosure for Sonoff mini used indoor only ,could be used on light inline wire, work in progress i will finish it in December 2022. 20211128_finished, ready to test on print 20220412 the 4 holes on corners are made to…
This is a very simple mount that holds the roam in place with light pressure from the prongs sticking up. It is intended to be stuck down to a surface using 3m double sided strips. But can easily be modified for screw holes. This initial…
We have one surround wall-mounted and the other on a small side table. I made a stand for it to sit at ear level. I printed it with 5% gyroid infill, and it's strong enough—no need for more material. The radii aren't G2 curvatures, but…
Držák adaptéru Sonoff Zigbee 3.0. Pro připevnění na polici nebo na zeď pomocí dvou šroubů. Adaptér je zajištěn v držáku zasunutým USB konektorem a našroubovanou anténou na druhé straně. Tiskárna: Longer LK5Pro Materiál: PETG, C-Tech,…
A remake of the included mount for the SNZB-02D in case you want to make extras, and another mount for use on dry boxes. The other mount can also be used on windows, or any time you want to mount the sensor on the interior of something,…
A simple case for a Raspberry Pi and the Sonoff ZBdongle-E, not ZBdongle-P! Pay attention, they are almost the same dimensions and look the same. I think all -E models have the label “Zigbee 2.0 USB Dongle Plus ” on them while the -P…
The original wall mounts from Sonos hasn't arrive in the shops yet. And I needed a quick solution so i could use my new pair of Era 300 as surrond speakers in my living room. Not a sexy design, but they work fine. You need 2x M5 screews…
The case uses tabs with 4mm holes to attach paracord. Designed to be easily clipped to a backpack or hung around campsite. Access hole for USB-C port and power button on back. Used supports for front top overhang, the tabs to not need…
Enhance your audio setup with this custom-designed SONOS ERA 300 wall bracket, enabling a full 360-degree rotation for optimal sound direction. Tailored to the sleek contours of the SONOS ERA 300, this mounting plate ensures secure…
Sonoff ZBMINIL2 DIN Rail Mount Print Terminal Mounts and snap piece from the original design from Harry .
Slim case for the Sonoff SNZB-02 ZigBee temperature and humidity sensor. This holder helps you to easily access the sensor without sticking it directly to the wall. Install the case with a screw or double sided tape and slide the sensor…
Thanks to @CPS_Systems_639833 for the improved remix. The friction bumps are working great. I wanted to screw and not glue the holder to a shelf, so I added 2 mounting holes. The holder works for the P- and E-version of the dongle.
Material PLA Nozzle 0,4 mm Layer height 0.2 mm
Sonos ERA 100 wall mount consists of 4 parts, which are connected to each other with the help of Allen screws a standard ruthex M3 heat inserts. M3x8 cylinder head - 4pcs M3x10 tapered head - 4pcs Recommendation for printing: nozzle 0.4…
A simple and sturdy mount for the Sonoff Zigbee & Thread Dongle Plus (MG24). This holder provides a snug fit for the dongle and includes enough space to accommodate the included USB extension cable for better signal placement. There are…
Horizontal wall mount, slightly tilted with some extra space for the usb cable. It is ment to be permanetly connected to electricity, as the on/off button is covered by the wall mount.
IOT enabled Power metering on the go I designed this housing to have an power meter which can be read out directly and in an existing IOT environment at the same time. Due the fact that the sonoff devices could be flashed with the tasmota…
Cover (sonoff_d.stl, sonoff_g.stl) printed from PETG but if you want you can print what you prefer. Cap (sonoff_k.stl) printed from flex filament (TPU).
An enclosure/case for a Sonoff 4CH Pro R2. Below the sonoff there is some room for wires or/and Screw Terminal Blocks. The walls are 3mm thick. I have used m3 Brass insert nut Injection Molding from…
Based on whocares333's Sonoff Zigbee 3.0 Dongle Mount. I added two hooks to mount this sideways on a Skadis peg board. Printing needs some supports for the holding brackets and the Skadis hooks.
Sonoff mini-d DIN rail mount
Sensor 6 mm in diameter. Sonoff DS18B20
fits with or without the original charger
I wanted to mount the sensor to the underside of a self, and the included magnetic mount doesn't allow it to rotate close enough to horizontal. So I designed this clip, which has allowances for the top button and the USB-C socket on the…
This quick and easy print is for mounting your sonos ray to your wall. Required hardware: 2X M5 screws for the sonos ray Superglue to glue the 2 halves together with the middle piece Mounting hardware for hanging the mount to the wall…
SONOFF ZBMINIR2 DIN rail mount. The model shown in the photos was printed with PC FR filament (0.2mm layer height).
Quick and easy wall mount for sonoff zigbe bridge ( LINK ). You can use one or two screws to mount it. Printing instructions: no supports needed print in vertical position as on pictures I prefer PETG but other materials can be ok too…
This is meant as a stand for the Sonos Play:1, which will also allow you to coil up the extra cord within it. The stock cords that came with my Sonos are designed to stick straight out the back while sitting flat on a table, so this does…
The Sonoff SNZB-02 sensor is a simple and cheap ZigBee temperature and humidity sensor. The default mounting option is using a sticker to attach it to the wall. However, walls tend to be colder than the room they are in due to thermal…
Super Simple print to get those speakers on the wall. Notes: Import the two pieces into your slicer. Pick your colors Place the shelf upside down and the swivel upright. Print PLA or PETG Attach to the wall with appropriate wall anchors…
As DrZzs call this; Jumper Holder Thingy Some of the new Sonoff Basics ( and probably others ) are being delivered with solder filling the serial programming interface. So if you want to flash it, you need to either remove the solder or…
Sonoff Universal Zigbee 3.0 USB Dongle mount with 25x8x2mm magnet slots. I made this to mount my dongle externally to my rack for better signal.
Hanging handle Sonoff Basic in three versions and two heights. I designed three versions: one suspended on a 17mm thick board, secound to be glued with double-sided tape and a version to be hung with screws. Each version has two heights:…
Added recess for Command Strip (small poster) mount. Added hole for mounting. Flattened section to create a “bottom” for alternate orientation while printing. Added friction “bumps” to the side to add grip for dongle. Note: Using this…
I needed something that would clear the mount for my monitor arm so my beam could sit further back on my desk. This uses the mounting holes at the bottom of the beam with 2 m3x16 screws.
EN: This stand allows you to place the Sonoff SNZB-06P presence sensor on flat surfaces like shelves or cupboards without wall mounting. Uses the included magnetic plate for secure hold Slot for easy routing of the USB cable Recommended…
I wanted to mount an oldie but goldie SONOS Play:1 speaker in the kitchen. A plain shelf would have done the job, but the cable mess would not have disappeared - that's why I have designed this one. I have uploaded two helper items too:…
I got the new Sonos roam and wanted a wall mount. So I designed a simple version so that it can be placed with the front facing towards the listener and with enough room behind the speaker for the charger cable. I hope you like it. PLA is…
With this adapter you can mount your Sonoff Mini R2 on a DIN rail in electrical box. To connect the holder with the clip is needed: 2x M3 screw and 2x M3 squarenut. Holes for nuts have dimension: 5,5mm x 5,5mm x 2mm. Inspired:…
I needed to house a Shelly 1 within a ceiling rose and it just wouldn't fit. Rather than buying a deeper section ceiling rose, I designed this with a mount. It housed a Shelly1 fine and worked a treat. You may want to test the threads to…
This is a Sonos Roam holder that takes the place of the bottle holder (bottle cage) on your bicycle. It should fit standard bottle cages and use the M5 bolts that come with your bike, but I left some wiggle room for the bolt placement. It…
I use the Ikea Skadis Pegboard as a panel to hold all my home automation and networking devices. I designed this so I can fix my Sonoff RF Bridge on this pegboard. Prints in around 2:30. Support is needed for the pegboard pins. If you…
Sturdy shelf for Sonos play 5 gen 1 speakers. I had them on these Flexon standards(https://www.flexson.nl/product/sonos-play5-1gen-standaard-wit/), but decided to wall mount them. I incorporated the top shelf of the flexon standards, but…
https://www.printables.com/de/model/688769-hook-for-vw-california-interior
This is a model for the Sonos Ray that elevates the speaker slightly off of the desk-top. It tilts the speaker at a 3 degree angle from the plane of the desk, and provides clearance underneath for keyboard/mouse wires, as well as…
This mount can be used if you want to mount the USB stick somewhere not directly in the USB port (which is very much recommended due to interference). It has two small holes in the back for screws but I just taped it to the wall. It holds…
Ich habe den Halter von Grund auf in OpenSCAD neu modelliert und unter der Basis sowohl Platz für einen Powerstrips Small, sowie Platz zum Entfernen geschaffen. Aufgrund der Bauart von Sensor und Switch halte ich ein Herausgleiten für…
This is a holder for the Sonoff SNZB-01 Zigbee Button
[EN] This is a wall mount enclosure for Sonoff Basic with cable gland PG3 and snap fit cover. Enclosure has been tested with Sonoff Basic R2 Enclosure is printed from PETG with layer height 0,2mm. Enclosure outer size is (LxWxH)…
Here is my simple solution to have a little more space on my work surface. The buttons of the Roam can still be operate
The original had two small parts holding the Sonoff that easily snapped. I widened them and connected them to the main body of the model to solve this problem. I used organic supports to print this on a cheap (and silent) Artillery Hornet.
As these sensors use batteries, I wanted a mount where I can remove the sensor, replace battery and mount it again without the need to replace the double sided tape. This collection includes the following mounts for: SNZB-03 PIR sensor…
I bought some Sonoff ZBMINI Extreme Zigbee Smart Switches which are normally placed directly behind the power socket. In my case I had to place them in a bigger box and mount them there. See article EAN 6920075742916.
Print like it is, front face down Insert your screen, flip it then choose the angle that match for you Open the back pre-drilled hole according to it Wire and secure it (you can use 2 zip ties to secure your wires at the back of the…
It can be printed with 0.2mm layer height and with no supports, no need to rotate the models. Remove both the sensor and magnet from their original cases. Keep the screws holding the sensor PCB to the case as they will be used later. Push…
Integrated supports are present. Print without supports in the current orientation Remove included supports Remove battery pack, disconnect hoses Mount using 2 screws Insert smart valve Re-insert battery pack and attach hoses I printed it…
Rotating Wallmount for the IKEA Sonos Speaker: SYMFONISK Additional Part needed: corner brace (DE: Winkelverbinder) Dimension: 90x90x65x2,5 2 Screws: M3x8mm with countersunk (DE: Senkkopf) 3 Parts: Symfonisk Groundplate (Extra Perimeter =…
cradle for sonoff SNZB-03 motion sensor made with openscad Have fun!
Here is the link to the Sonos one model https://www.printables.com/model/596960-sonos-one-boolean-tool Printed with Overture Matte PLA Wrist down No supports .05 layer height (The detail is incredible) Lightning infill
Outdoor case for the Sonoff SNZB-02P. I just taped the orange, magnetic mounting plate inside.
You can simply print this model using PETG (more durable than PLA) and TPU. TPU is very useful to completely absorb vibration from Sonos diffuser. The diffuser is entirely supported by TPU. Maybe is a good idea increase fill density in…
Remixed from Sonoff SV Case With Button by migi and the honeycomb holes from LM2596 and LM2596S Buck converter tool-less snap-fit enclosure - Ender, CR-10, 2020 by FedorSosnin . I liked the original case but it was missing two things for…
This is a vertical wall mount for Sonos Roam, inspired by some great designs such as https://www.thingiverse.com/thing:4867644 or https://www.printables.com/model/380346-sonos-roam-wall-mount. Unfortunately those did not fit my needs, as…
A remake of the Raspberry Pi 4 B Case - Home Assistant. One centimeter longer so it will fit the sonoff 3.0.
I've purchased a couple Sonoff SNZB-06P mmwave Zigbee sensors, but I didn't like that the size of the sensor was so large with the magnetic base. So I designed this back cover to make the device much smaller. It is possible to stick it…
Wall Cradle Bracket for Sonoff 02LD Temperature Sensor & Probe. I recently purchase the SONOFF SNZB-02LD IP65 Zigbee LCD Smart Thermometer (Probe Version). With the probe attached to the boiler flow pipe the temperatures can be monitored…
Sonoff Mini mounting system with sliding terminal cover, I have also included a version with a fixed cover. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.2 Infill: 45 Filament: Generic…
Wall corner mount for SNZB-03. Designed for double-sided tape mounting. You can easily slide slide the motion sensor in and out if you want access connect button or replace battery. Print a little smaller in case you want friction when…