Search results: 055

Lego Compatible (98055.dat) Dinosaur Head Tyrannosaurus Rex

This model is compatible with the lego system.

Lego Compatible (30553.dat) Hinge Arm Locking with Dual Finger and Axlehole

This model is compatible with the lego system.

Lego Compatible (10055pb01.dat) Minifig Hair Long Straight with Elf Ears Pattern

This model is compatible with the lego system.

Bandsaw insert (Grizzly G0555, King industrial KC-1433FXR, King KC-1401FX)

I designed this for my King Industrial 14inch band saw model KC-1433FXR, It also fits Grizzly model G0555 bandsaws as these are the same bandsaws with different branding…. This has a much smaller slot that lets you get in close with small…

OMAR IKEA shelf clamp 10055941 / 130531

Replacement piece OMAR IKEA 10055941 / 130531 to adjust the height

#0055 Elevated Stand for Echo Dot 4th Gen (or succulent planter) [3 Variants]

Here is a selection of 3 variants for an Echo Dot (4th Gen) stand. They are of slightly different heights (between 43 and 48mm tall) and the legs are of a similar tapered diameter. The tips of the legs contact the table at ~55mm diameter,…

Ikea Metod Screw On Leg Extender (402.055.99)

Check my other IKEA designs: NEW Ikea Metod Leg Extender (705.560.67) IKEA Metod Back 10mm Spacer Replacement (10036383 or 10039201) Why If your robot vacuum cleaner does not clean under the Ikea Metod cabinets (standard 8 cm is at least…

Lego Compatible (70558.dat) Minifig Head Sesame Street Bert

This model is compatible with the lego system.

Aquarium Spray Bar for JYC-0550 Water Pump

Aquarium Spray Bar for JYC-0550 Water Pump

Canyon Ultimate SP0055 Garmin Varia Mount

Loosen the two screws from the base plate from the handlebar mount that comes shipped with your Garmin Edge Place screw in the middle hole Attach base plate to the 3d print Attach/Screw onto your seatpost I used the following print…

Grizzly G0555 Bandsaw Zero clearance Table insert / throat plate

Grizzly G0555 Bandsaw Zero clearance table insert. This file has a notch to keep it from rotating. Two versions. One solid and one with ventilation holes for setups with dust collection.

Intimate Geometry - NSFW Hueforge 0055

Snap-on Mounts for Accessories on a Peak Design Travel Tripod or a Manfrotto 055XPROB

These are snap-on mounts for attaching camera accessories to the legs of a Peak Design Travel Tripod. I often use a powerbank and a wifi pocket-router to connect my phone or tablet to my cameras for remote control on macro shots or…

dfrobot BNO055 enclosure

4 brass insert nut M3 4 M3 1.5cm screw 1 test board 2 5x1 female header

Kawasaki ZX-4R Rear Tail Light and Side Fairing (Right) COVER-TAIL,RH,M .S.BLACK 36041-0055-660

Disclaimer: This model is part of a larger collection of ZX-4R 3D scans that I have on my profile. All models were scanned with my Metro x laser scanner at 0.2-0.3mm resolution. If you have managed to break any of the parts, you can use…

#055 Golduck – Low Poly Pokémon

Golduck takes on a sleek, athletic form in this low-poly style, its sharp edges and angular contours highlighting its streamlined, aquatic nature. The simplified geometry of its beak, claws, and head crest gives it a bold, powerful…

Anker PowerCore Speed 20000 PD Tripod Leg Clamp - for Manfrotto 055 Tripod

Clamp to hold an Anker PowerCore Speed 20000 PD on a Manfrotto 055 tripod leg. It should also fit any other tripod with a leg diameter of 30 mm. This might also fit other Anker PowerCore products with similar measurements. For reference,…

SideWinder Air Pump 62055 Nozzle

The nozzle of my SideWinder Air Pump 62055 was lost. I downloaded 'TheAlmoner' Remix, scaled it down a bit and chopped the end to fit my air mattress and it's a perfect fit ! This is the remix of a remix Printed with PETG on a Bambulab P1P

5055 Electric Motor Mount for RC Airplanes

I was building a Nexa Beech G58 Baron RC model aircraft and really disliked the stand-off method the kit provided for mounting the 5055-400kv electric motors I selected to use. I also don't like the standard motor mounts that come with…

Philips QC5055 clipper cap

Clipper for philips qc5055 haircutter

Upper wash arm P2 - SMEG Essentiel B - Réf : 694570055

I printed my first parts in PETG, but when I used them, once I pulled them out of the dishwasher, they were deformed. They couldn’t handle the heat inside the dishwasher. That’s why I printed them in PCCF "Prusament PC Blend Carbon Fiber…

Eheim Absperrhahn / stopclock holder - 4004512 4005510 4004412 4005410

This is a custom-designed holder for the following Eheim models: Eheim 4004512 Eheim 4005510 Eheim 4004412 Eheim 4005410 The holders are available in two different sizes, 20mm and 30mm. You can choose between a single holder or a dual…

Steyr 8055 Light Frame

Printed with black Generic PETG. 0.2mm QUALITY The model is symmetric. It does not matter if you want to print the frame for the right or the left light.

Adafruit BNO055 Calibration Helpers

The enclosure prints in two parts and requires 4x M2.5x10mm screws. The ramp is set at 13 degrees East of North, and 60 degrees down from horizontal (aligned with the magnetic field in Santa Cruz, California). The wheel is for calibrating…

Velleman K8055N Case

Case need Support 10% Infill

Zámek dveří pro pračku ELECTROLUX, ZANUSSI 5600 4055113437

Tiskl jsem z PETG se 100 procentní výplní a 4 perimetry. Jedná se o dočasný háček do zámku dveří u pračky. Např. než dorazí nový náhradní díl. Funkčnost dílu je v pořádku, životnost nemám otestovanou.

Lionel 8702-132 (2055 Hudson) brush plate

I recommend printing this at 0.2mm with 100% infill, using PETG or another strong and heat resistant material. You will have to remove the brush holders/springs from the old assembly and attach them to this new one in order to use it.…

Connect 42390556 Mixer Coupler - Spojka motoru a čepele tyčového mixéru

Printed successfully on MINI+ from recycled PETG with 100% infill. Works magics.

Manfrotto 055c Stativ Platte für Stativkopf, Manfrotto 055c tripod plate for tripod head,

Manfrotto 055c Stativ Platte für direkte befestigung des Stativkopfes. Diese Platte ersetzt das Originalteil R055,10. Der Stativkopf kann direkt auf die Platte geschraubt werden. Die Mittelsäule entfällt. Benötigt wird eine Inbusschraube…

Upper wash arm P1 - SMEG Essentiel B - Réf : 694570055

I printed my first parts in PETG, but when I used them, once I pulled them out of the dishwasher, they were deformed. They couldn’t handle the heat inside the dishwasher. That’s why I printed them in PCCF "Prusament PC Blend Carbon Fiber…

ATS 3055

Here you get now a better version of the ATS 3055. It consists of three single pieces, so you can print and paint them separately for a better result. It is scaled for a 1:43 Model Car for a ~17" Wheel, but can be scaled of course. (Not…

Manfrotto Stativ 055XPROB Haken kurze Mittelsäule 055xccsb hook for short center column 055xccsb

Ein Haken für die kurze Mittelsäule 055xccsb für das Manfrotto 055XPROB Stativ. Getestet mit 21 Kg Belastung wobei sich der Haken nur leicht verformt. Die Bruchlast habe ich nicht ausprobiert. Für die Befestigung benötigt man eine…

Socket wrench insert YATO YT-1055 set

Socket wrench insert. Repair kit for YT-1055 set

Manfrotto Stativ 055c Haken für Mittelsäule Manfrotto tripod 055c hook for short center column

Ein Haken für die Mittelsäule des alten Manfrotto 055c Stativ. Für die Befestigung benötigt man eine Schraube M8 x 40. Es empfiehlt sich eine selbstsichernde Mutter zu verwenden damit man durch zu starkes anziehen das Aluminiumrohr nicht…

CM-2055M - BEL MPPS regulator

BEL MPPS regulator CM-2055M

055 Vorsicht: Spielende Zahlen! Hexgitter

Vorsicht: Spielende Zahlen ist eine Sammlung von Lernmaterial für Unterricht und Selbststudium. Nach und nach wir zu den meisten Drucken auch noch ein fOrscherblAtt beigefügt, das den individuellen Lernweg begleiten soll.

Yahama Logo Badge for Club V Series PA Speakers, PN WJ370400/CBY05500

Want to make your Club V series speakers look decent again, but found out a replacement badge isn't sold anywhere? Print your own faithful reproduction! Category: Electronics

Bruder 03055 repair kit

You need to cut off the protruding part, as shown in the photo, and glue in a repair piece. Mirror the part for the other side. I used cyanoacrylate glue and hardener.

20550

Press brake die for sheetmetal 0.2 layer 0.4 nozzle Sunlu PLA+

BMW Idle Valve Mount Rubber Mounting 13411705564

A replacement hood rubber mounting for many BMW models. This is a replacement for BMW part number 13411705564 . I created this part specifically for my BMW E28 535i but it is used on the E30, E36, E46, E34, E39, E24, E23, E32, E38, E53,…

Dewalt DW055PL Laser Distance Measure Skadis Mount

Skadis Mount for the Dewalt DW055PL Laser Distance Measure

Hampton Bay NXT-SL-12 / Nextech SKU# 1005554635 Lower Bracket

This is the bracket that connects the ground spike to a Hampton Bay NXT-SL-12 / Nextech SKU# 1005554635 Solar Light. Mine broke and I remade the part in OnShape so that I didn't have to throw out a working solar light because of broken…

Zero Tolerance 0550 Punisher Skull Scale

I made it for my ZT 0550. Fits pretty well if printed with no hurry. I user Bambulab PLA-CF filament for black part and Sunlu PLA for the skull. On photos you can see my scale printed on Bambulab X1C 0.4 nozzle with 0.12 layer height and…

Trivec Avant Model 2055-3 Discovery Drive Adapter

This adapter lets you mount a Trivec-Avant 2055-3 SATCOM antenna on a Discovery Drive azimuth/elevation rotor. You can aim the antenna the same way you would a dish or ham antenna to maximize signal. The larger flat section bolts to the…

zajišťovací klip pro robotický vysavač FIELDMANN FZBR 3055-A

zajišťovací klip pro kryt robotického vysavače bazénů. Původní často praská, náhrada je příliš drahá. Vyzkoušeno z materiálu PRTG a ASA

3055_portabridas plastico

pieza para poner un adhesivo y luego utilzarla para sujetar cosas con bridas de plastico.

Edesa dishwasher handle replacement VMI000055 – AS0028066

Replacement for the handle of some Edesa/Fagor dishwasher

Profilo Fridge Door Shelf (BD2055WFVN)

I designed this model after my original part broke, and it fits securely in place while maintaining good strength for everyday use. Material: I used PLA and it works but PETG recommended for better durability. Layer height: 0.24 mm…

Briggs & Stratton 494439 Rotating Screen Replaces 690749, 691055, 805723

Briggs & Stratton 494439 Rotating Screen Replaces 690749, 691055, 805723 Replaces Old Briggs # 690749, 691055, 805723, 497417, 491793, 807566, 280829, 224135 Print upside down and no supports needed. I wouldn't recommend PLA because it'll…

Frigidaire FGHT2055VF1

The lower hinge pin (that the fridge door sits on) on my Frigidaire FGHT2055VF1 came cross threaded from the factory. I needed to switch which way the fridge door was hung, and until I could get a metal replacement pin sent to me I…

einhell crank and hand shank - pt n° 434055001080 + 434055001083

dopo che mi si è rotta la manovella per la regolazione dell'altezza della lama del mio primo banco sega ( Einhell TE-CC 1825 U ) mi sono subito adoperato nel clonarla. i pezzi di riferimento sono i seguenti: pt n° 434055001080 +…

Belden AX105566 Latch

Replacement for the fragile locking lever on the Belden AX105566 termination tool. Print in PETG or ASA. Hot Pink color is optional Supports are required, print solid and in the orientation shown for best strength.

Lens Cover for Bosch GTC 400 C Thermal Camera (16055002CR)

Lost the lens cover for my Bosch thermal camera so I decided to recreate it based on photos and share it here in case anybody else needs it. It fits perfectly and follows the original design as closely as it can. There is, however, an…

Grizzly G0555 tension knob expander / enlarger

The stock tensioner knob on the Grizzly G0555 is small and can be hard to turn. I made this to make it easier to grip and turn. It snaps directly over the top of the knob without any adhesive. Although you could use some epoxy to make it…

Support télécommande SULION 055766

Support mural pour télécommande de plafonnier SULION. Fixé sur un obturateur de prise LEGRAND modèle Dooxie

Ambico V-0552 Replacement Leg Strut

Replacement leg struts for Ambico V-0552 tripod. Designed for corner to corner printing on Prusa Mini. They are probably shorter than the original ones, so best to replace all 3 probably. Recommended to print on its side for strength. I…

Spare part Siemens dish washer / Gelenk fuer Siemens 12005549 Tassenetagere für Oberkorb v4

save some money for overpriced spare parts, happy if someone else can use it. print with supports in PETG 0.1mm height

Door Latch/Catch for Dishwasher (Quick Fix Edition for PN: 4055283925)

This was a design for our Zanussi ZDT 6252 dishwasher, the door latch/catch part number 4055283925, but the same part is used in many other compatible models, even from other brands. I've seen Electrolux and AEG just to mention two,…

Oscilloscope display PM3055

Easy to print frame for philips PM3055 oscilloscope Has to be glued in place Category: Tools

LS055R1SX03(2K-5.5inch)_LCD-BasePlate_and_PCB-Case

About Double Side Tape Frame for LCD and PCB Case ( with Button Parts ). for example: 5.5-inch 2K LS055R1SX03 1440x2560 LCD Display for Sharp Panels with HDMI and MIPI to 3D Printer Board, Detachable…

Motion Pro 08-0550 Steering Head Bearing Race Driver Set Holder

I purchased a Motion Pro 08-0550 Steering Head Bearing Race Driver Set and wanted a holder to put them in my toolbox, the race adapters snap in place.

PHILIPS PM3055 oscilloscope control panel case

PHILIPS PM3055 oscilloscope control panel case originally made of ABS in brown color by PHILIPS main retaining clips were all broken in the sample I took, I made precise measurements as far as I could but still can be deviations from…

297305500 - Electrolux Freezer Clip

Save $16+ and print it yourself Any plastic is good, I used PLA but PETG is probobly a better choice IMPORTANT! Print on its side as in the photo, this is extremely important for load transfer.

VASE DOTS 055

Parametric 8.4cm tall object with rounded circular geometry and a dots pattern. Engineered for precise 3D printing.

VASE DENDRITE 055

Parametric 5.5cm tall object with square 4-sided geometry and a dendrite pattern. Engineered for precise 3D printing.

Fieldmann FZBR 3055-A flap

This a replacement rear flap for Fieldmann FZBR 3055-A pool vacuum. Printed on Prusa MK3S MMU2S 0,4mm using PM RE-PETG at 100% infill in the orientation shown, with supports on print bed. Takes about an hour with 0,2mm DETAIL profile. Use…

Motion Pro 08-0550 Steering Head Bearing Race Driver Set Holder

I purchased a Motion Pro 08-0550 Steering Head Bearing Race Driver Set and wanted a holder to put them in my toolbox, the race adapters snap in place.

Grizzly G0555 tension knob expander / enlarger

The stock tensioner knob on the Grizzly G0555 is small and can be hard to turn. I made this to make it easier to grip and turn. It snaps directly over the top of the knob without any adhesive. Although you could use some epoxy to make it…

PHILIPS PM3055 oscilloscope control panel case

PHILIPS PM3055 oscilloscope control panel case originally made of ABS in brown color by PHILIPS main retaining clips were all broken in the sample I took, I made precise measurements as far as I could but still can be deviations from…

Filter holder for Karcher FC3 / FC5 / EWM2 (4.055-110.0)

Many time ago I lost a little thing from my electric floor cleaner Karcher FC3. It was filter with plastic holder 4.055-110.0 by original partnumber. Without it valve in clear water tank doesn't work and water doesn't dispense on rollers.…

Door Latch/Catch for Dishwasher (Quick Fix Edition for PN: 4055283925)

This was a design for our Zanussi ZDT 6252 dishwasher, the door latch/catch part number 4055283925, but the same part is used in many other compatible models, even from other brands. I've seen Electrolux and AEG just to mention two,…

Profilo Fridge Door Shelf (BD2055WFVN)

I designed this model after my original part broke, and it fits securely in place while maintaining good strength for everyday use. Material: I used PLA and it works but PETG recommended for better durability. Layer height: 0.24 mm…

Abus Bordo Lite 6055 mount for Brompton

Solid mount for an Abus Borgo 6500 Lite. You can install it on the top tube of the brompton with 2 ziptires. You also need a strap (≤ 30mm) to secure the lock.

"CR055" KZ ZSN Pro / Pro X faceplate

Custom version of JohnC's faceplate You don't need to mirror the model to print, you need to print the same model twice I'll add a photo after I print it out

Lego round flat tile 2x2 with hole 15535 or 6055313

Lego round flat tile 2x2 with hole 15535 or 6055313.

Lego Compatible (11055.dat) Flag 2 x 2 Square (Thick C-Clip)

This model is compatible with the lego system.

HSP 86055 Steering Joint Cut

HSP 86055 Steering Joint Lever I made it for 1/16 Himoto EXM-16 At also should be compatible to: HSP KidKing RC 94182 94183 94185 94186 94187 Himoto - EXB-16,EXT-16,EMT-16 Print details: I used PLA 0.16mm (0.2 is also fine) with 99.9%…

Brompton Rack Mounting Bracket for Abus Bordo Lite 6055

Printed with PETG, 0.2 mm layer height, 6 perimeters, 50 % cubic infill. Print was oriented as shown in picture to yield best strength. Organic supports were placed to support large overhangs. Assembly requires M4 bolts and self-locking…

Patuopro bit holder pta005501

Two magnets 6x2mm

Lego Compatible (6055.dat) Panel Wall 6 x 6 x 6 Corner

This model is compatible with the lego system.

Lego Compatible (30554a.dat) Hinge Arm Locking with Single and Dual Fingers without Hole

This model is compatible with the lego system.

Echo P021005581 Chainsaw Oil Cap / Echo P021005591 Chainsaw Gas Cap (CS2600,2700,310,260TES,350WES/TES,352ES,353ES,360TES,361WES/SH305S)

. Print Settings Printer: Don't matter Rafts: Doesn't Matter Supports: No Resolution: 0.1 Infill: 90 Filament: Any ABS Any Notes: Maybe need small resize x and y for shrinkage's compensation. Крышка должна накручиваться без усилий, но не…

Filter holder for Karcher FC3 / FC5 / EWM2 (4.055-110.0)

Many time ago I lost a little thing from my electric floor cleaner Karcher FC3. It was filter with plastic holder 4.055-110.0 by original partnumber. Without it valve in clear water tank doesn't work and water doesn't dispense on rollers.…

LEGO compatible Fence 30055 1x1x2

Disclaimer: This design is an independent creation and is not affiliated with, authorized by, or endorsed by the LEGO Group. It is designed to be compatible with standard building blocks. This brickvariation corresponds to the LEGO Fence…

Lego Compatible (93055.dat) Minifig Sword Katana (Dragon Guard)

This model is compatible with the lego system.

Adafruit BNO055 STEMMA QT Sensor-Modul

Das Design ist für den 3D-Druck optimiert und eignet sich gut für Elektronikprojekte, Robotik, Prototypen, Sensorhalterungen und DIY-Anwendungen. Das Modell wurde von Amir Mobasheraghdam erstellt. Enthaltene Dateien Dieses Projekt…

3 pcs Drill Adapter Set Wall Holder 055 I for screws or peg board

Tool holder for 3 pcs Drill Adapter Set. We provide two versions to download: Screw: 4mm holes for standard screws for mounting on wooden or stoned walls Pins: for peg boards of standard size Sizes: L - 80mm W - 38,99mm H - 40,49mm We…

Manfrotto 055XB Mount Plate

Manfrotto 055XB Mount Plate.

Side panels replacement for MPPS CP 2055 box

Side panels replacement for CP 2055 box used for: https://www.bel-shop.eu/stavebnice-mpps-regulatoru-pro-napajeni-boileru-z-fotovoltaickych-panelu/ original box here: https://www.bel-shop.eu/plastova-skrinka-combiplast-cp-2055m/ I printed…

kotlík S0055

kotlík (nádobka) do sifonu do sprchového koutu rozměry: 65x73/ø78,5

Aquarium Pump Cage Filter Mini JYC-0550

This is a filter cage for a mini DC Water Pump JYC-0550

Worker F10555 Bottom Picatinny Rail

This is the bottom rail attachment for the Worker F10555 Longshot pump grip Uses M3 hardware. I used 12mm screws.

lego piece 6055629

sorry for the scale it was designet wrong so you need to print is at 10% scale