477 models
Compatibility: This case design is compatible with Raspberry Pi's 2B/3B/3B+/4. It may be compatible with other models, however, these were the ones I was personally able to test it on. Two Top Depths: (01/06/2022) The top half is now…
Hello there this a remix of the famous Moon Lamp for the use with WS2812B Led Strips and WLED (NodeMCU ESP 8266) to controll the LEDs. Moon Lamp Diameter approx.: 154 mm / 6 in Hole for the screwable LED Strip Mount approx.: 52mm / 2 in…
A 10-inch rack mount for two Raspberry Pi devices. Compatible with RPi 2B, 3B, 4B and 5B. This model is part of a series of 10-inch rack mounts I've designed. You can check out the others here . Do you like my models? Consider buying me a…
B2B JST XH Straight Connector pitch 2.54mm 2/3/4/5/6/7/8/9/10/11/12 pin
This model is compatible with the lego system.
A modular, 2 part, 19-inch rack mount for the Raspberry Pi 2B, 3B, 4B and 5B devices. This mount is part of a 19-inch modular rack mount system I designed, you can mix and match the modules with other mounts. Take a look at my models here…
Welcome to The Low Poly Auto Show! This is a remastered version of my low poly Subaru Impreza 22b STI. Printability has been enhanced and the design has been cleaned up. Print this model with NO SUPPORTS. Details/fit may not print as…
I have put together a couple of 3MF files that have a few helping hands on printing this nice figure that I've remixed from MatheusEvan. My model sits at about 17cm. I found the original model was quite big, it had a very large base that…
This model is compatible with the lego system.
DC UPS based on LX-2BUPS module (5V/9V/12V, with a USB Type-C power connector). This is useful for powering internet switch/router during a power outage. If you need 5V UPS with USB output, use this design instead. Aug 2024 update: I…
Welcome to The Low Poly Auto Show! This is a low-poly Subaru Impreza 22b STi. It is a remix of a model designed by u/jkmonger on Reddit. It is designed to be printed without supports at 0.1/0.2 mm layer height if you have a solid machine…
Designed to fit a standard 26mm tyre. +3mm offset, 12mm hex. Will take up to a 4mm shaft. For personal use only. No commercial sales.
Use flexible filament, like TPU, if you don't want them to break right away! Update! This model has been redesigned. Go here. Updated models for 2BA and ¼ BSF available here…
The mini-tray was designed as an alternative to the standard JEDEC tray for semiconductors. It has the same width as a JEDEC tray, but its length is a third of that of a JEDEC tray. Thus, three mini-trays lined up have the same…
Simple stand for the HS-02A/B from Fnirsi. New design but based on this: https://www.printables.com/model/585253-improved-hs-01-stand Like the original, prints without supports. ASA or ABS recommended. I only have a HS-02A, so not tested…
UPDATE: I also have done a 32x32 Matrix in a IKEA picture frame with WLED: https://www.printables.com/de/model/501107-led-rgb-matrix-ws2812b-esp32-wled-32x32-round-squa…
Staved off the convert to Octoprint for 5 months, wanted a slim adaptable case for various mounting positions in my enclosure. Loved the original Voronoi design but hate using hardware to assemble, redesigned for a snap fit enclosure and…
Test samples according to the ISO 527. 2A is slighty larger and 2B shorter
The new smallest siren on my Printables!! I made this Q2B because I've been getting back into biking recently and since my previous bike bell broke when I crashed a while back, I had the idea of making a bike-sized Q siren that could…
5V UPS based on LX-2BUPS module (5V, with a USB Type-C power connector). This is useful for powering internet switch/router despite a power outage. In case you need a 9V or 12V UPS, or you need a cable output with DC jack instead of USB,…
Case for Ardusimple simpleRTK2B with lid. Dimensions 75 x 75 mm. 3D printable file case made for SKU AS-STARTKIT-BASIC-L1L2-NH-02. Construction features: - 3x metal thread ready (M3 screws) supports for motherboard raised fixing - micro…
A NeoPixel / WS2812b controlled LED Matrix with 16x16 Pixels Easy to print: Can be printed without support, Filament Type doesn't really matter. I printed mine with PETG, but PLA or something else should work fine as well! I printed the…
This project provides the models for a printable vacuum clamping system utilizing the Dewalt Grabo DCE592B lifters. All fittings are ¼" push connect lines and ¼" NPT thread. BOM Dewalt Grabo DCE592B lifter Minwax Polycrylic sealant 1/16"…
Hello Makers, i wanted a bigger LED matrix with 32x32 LEDs. So i looked for a nice picture frame that fits also for the depth. I found a good & cheap one on IKEA. On Youtube there are lots of tutorials to build a 32x32 matrix out of four…
I found a great tutorial for electronics that was missing only the case. So I started modeling. Many thanks to Crazymakers for their work and sharing. Link to the video : Link to the website :…
I needed a simple clock in one room, so I designed one. 24h display to be equipped with WS2812B LED-Strips with 60LEDs/m. Each digit will need 15 LEDs, two on each segment with one LED hidden between to segments. I did a lazy wiring job,…
Print Settings 0.4mm 20% infill Support - Touching Build Plate Scale to 10% design is 10:1 to allow for detail. Can be printed with support and face down for quick/draft prints in under 1h, or with support face up for higher quality…
A 6-inch Rack Mount for the Raspberry Pi 2B, 3B, 4B, and 5B. This model is part of a series of 6-inch rack mounts I've designed. You can check out the others here . Do you like my models? Consider buying me a coffee ;) Updates 02 August…
LED diffuser grid for ws2812b strips (60 leds/meter) display. I would recommend to print it 0.2 layer height, print the 3 first layers with white PLA then change filament to black. Pictures are from 4 8x8 grid glued together for a 256…
Print it laying down. put the leds in the slots and wire it up. diffuse it from the front side
Two methods for fixing the channel , holes along the center, and tabs on the side, these are 190mm long. I printed these in PLA, flat on the bed with supports everywhere, might get away without supports I didnt try. The led strip I used…
I redesigned and draw this Modell totally new in fusion360. The idea though is from user Forenseil : https://www.printables.com/de/model/811540-low-friction-high-speed-optical-illusion-windturbi The wheels are now in two parts, so they…
Converted the original authors STLs to STEP with freecad and then modified to fit a USB C output connection. It's not perfect but it's functional.
I designed this motor cover to protect the motor from dirt and water. It's designed to clip onto the motor without the need for cable ties or additional mounts and it has proven to work extremely well. If you find this part useful please…
Scale 1:42, but is designed to go with Captain Ahab's WW1 micro armor planes https://www.thingiverse.com/thing:4680918 Designed in Fusion 360 Same plane used in Battlefield 1
Notes: Phase offset 80mm from bottom of pole mount. Designed for m2.5 hardware. Use the (4 mounting hole) battery holder variant shown in pictures. There is a 2 mounting hole variant that will not fit because the terminals are in a…
This is a case for the ArduSimple simpleRTK2B board Category: Engineering
Remixed Xlnt3D's nicely designed rear TT-02B shock tower ( https://www.thingiverse.com/thing:4494409 ) so I could use my stock screws. This is a great replacement to add rigidity to the rear shock tower so your shocks can do their job.…
Just another seven segment LED clock. Current version of SW working, but it isn't final version. What is working: time on dislpay synchronization from NTP server time in local time zone. This zone must be specified manually on source code…
90mm EDF 12blade Propeller. I recommend printing it from stronger filaments like : PETG , Nilon , Carbon reinforced nilon ... Category: Other
Remix (resize) case for Generic 8 x Neopixel (WS2812b) Stick / Bar - Case - WS2812b-8 Support me at: Buy Me A Coffee Original model did not fit these generic Neopixel 8 Bar / Sticks I found on aliexpress, had to resize. Aliexpress Amazon
RGB matrix case Diffuser (print in place with color change) Case stand Back frame to fit esp32 dev boards, mini bread boards, etc Printing Instructions Please use white filament for diffuser. The case & stand can be printed from any color…
This is a remix of nushipwright 's " Spot Welder Box (JQ-DHJ02B spot welder) " with a handful of improvements listed below. Increased wall thickness across the board from 1mm to 2.5mm making it far stronger Added 4x M3x8 screws to avoid…
The perfect stand for the Aneng 622B on your desktop. In the version in photo, the upper Probe clamp is present. In the STL there is also a lower clamp to give the probes more stability. Print this stand on the left side with 20% infill…
Wordclock Matrix 11x11 Frame for WS2812B LEDs. LEDs can be simply clipped into the frame. For the Wordclock Frame i use a IKEA Ribba 23x23cm Frame https://www.ikea.com/at/de/p/ribba-rahmen-schwarz-40378401/ Source Code for this project…
Notes: Phase offset 75mm from bottom of pole mount. Designed for m2.5 hardware. Use the (4 mounting hole) battery holder variant shown in pictures. There is a 2 mounting hole variant that will not fit because the terminals are in a…
Narrow end profile improves air speed for removing heavier debris such as wet leaves
Here it is! Filament Darts. Try recycling filament for the point. Set up a cardboard box for a target and you're in business. Also works with those hole-filled plastic targets everybody seems to have. Update: New models ! Significantly…
This model is compatible with the lego system.
This is a simple mount for 10mm wide WS2812b (often known as neopixels) to mount along 2020 extrusion. It mounts the LEDs in parallel to the extrusion profile used. 100mm and 150mm lengths provided, as well as a .STEP and Fusion 360 file…
TowerPro MG90S offers a maximum of ~1.84 kg/cm torque at 5V; the alternative option Savox SH-0255MG offers ~3.4 kg/cm torque at 5V. However, Savox is significantly more expensive. TowerPro MG92B has nearly identical dimensions as…
Remote holder for the universal QD-U02B Air Conditioner control board which is a cheap replacement for burnt AC electronics. It allows operation of the remote without removing it from the holder because you can slide its cap through the…
I have downloaded this file, and it did not fit the Siboor led lights I had purchased, Since I printed them on ABS, as it shrinks by around .5% on this long piece it was 2mm too short, so it was remixed with those tolances in mind, and…
The clock is based on WS22812b addressable LED strip and WEMOS-D1 mini (ESP-12F) board. In my case it is running the ESPHome software in combination with Home Assistant (see link below). Fusion 360 files are also available. To get result…
Remix of the VORON WAGO extrusion mount, splitted into to independant mounts. Modified it to fit on my Mercury One.1. BOM 4* M5x10 Printing settings Voron print settings Check out my other ZeroG Mercury1 mods
Updates : 8/1/2024: Posted Mk2v1 10/13/2024: Added extended Nosecone coupler for a more secure fit Introduction: The 3-in Bullpup is an upscaled version of my Bullpup - Extreme Series rockets. It incorporates a tailcone motor retainer and…
Just another case for the LTT screwdriver. I sliced the model with PrusaSlicer 2.5.0 without adjusting any setting and printed it with the inside of the case facing down. Added a version 2: added 2 pairs of magnets at the latch deepened…
3d printed Connector for jumper wire 12mm Dupont as soldering aid. Find out everything you need to know about the connector on my blog: https://nerd-corner.com/printed-connector-as-soldering-aid-for-jumper-cables-and-led-strips/ 14mm…
This is a remix of 0110-M-P's excellent Raspberry Pi case. All the legwork was done by them - I happened to want a simpler looking design and needed to play with designing grilles that could be 3D printed. See 0110-M-P's thing here for a…
Habe die Clips für die Nummernschildbefestigung des Thule Fahrradträgers verloren. (Ersatzteilenummer 51378 von Thule Clip 2A + 2B passend) Vielen Dank an @vaterderhuehner für die Arbeit. Ich habe die Clips auf mein Modell angepasst.…
Voron Trident Power inlet CW2B
Insert holds: M12BLIDRC M12 battery (in my case M12HB2.5) M12TC2 USB charger Small compartment in the back for bit holder or other small parts Remaining space of the organizer is used to store a SHOCKWAVE Set 38pcs (4932492009) or other…
After converting my Ender 3 S1 to Klipper, I was looking for a solution to mount the Raspberry Pi 4 on the printer housing. On my search I came across the brilliant "Modular Snap Together Raspberry Pi 2B/3B/3B+/4 Case w/ OLED & Fan…
I have been having a hard time soldering the LED with the jumps due to many movements that make me solder my hand with the table. None of the solutions that I found were proper to my case, I wanted something straight forward that holds…
This is a replacement gear for the Dyson V6 motorized brush head. There was a number on my original gear: “T103310 2B”. I do not know if that is a model number or not. It goes inside the motor assembly and connects the motor to the brush…
The first version published here is a rather minimal case with a surprisingly effective diffusor for one of those quadratic LED matrices you can get on Aliexpress with 256 WS2812b LED on it, 16 rows a 16 lights, spaced in a 10mm raster. A…
Simple small box for GPS RTK module - used for Vitulus robot , but could be usefull for anyone.
Printed on an ender 3 v3 se with PLA. Layer height: 0.2mm Nozzle: 0.4mm supports: only for the Base Required PARTS* 4x standoffs (they should come preinstalled with the k2b board) 4x M3*6 countersunk screws (to hold the board in place) *…
Printed with 0.2mm layer height and Elegoo's cheapest PLA. The UPS board clips in without tools. Place the USB end in first and push down other end to clip in. If you need to remove the board, you may have to remove the xt60 connector and…
NieR:Automata HueForge Print at 100% infill with a layer height of 0.08mm with a base layer of 0.16mm Filaments Used: PLA Kingroon Black Transmission Distance: 0.6 PLA+ eSun Gray Transmission Distance: 2.5 PLA Kingroon Skin Transmission…
I had a bunch of WS2812B modules lying around so I decided to make this gear/flag display. If you don't have any of these modules you're probably better off ordering a 8x8 matrix and using that instead as there's less soldering to do, but…
This replaces the LED and switch mount for MAME KOF American Type Push buttons. Video example: https://youtu.be/QJ1OX\_ZHtn8 Buttons: https://www.aliexpress.com/item/33001974422.html LEDs: https://www.aliexpress.com/item/32960205936.html…
Creepy 3D spider for Halloween! 🕸 In this improved Version 2 , the body and legs are printed separately and then assembled. Additionally, the cross on the spider’s back is available as a separate piece – perfect for multi-color printing…
STORE LINK: Shop on BRS Store VCORE 4.1 - 4.0 - 3.0 - 3.1 - 3.2H AWD modules for Vcore ALL Vcore (Non hybrid) Based on the "best seller" product of BRS-ENGINEERING, the BRS-AWD for Vcore 3/3.1, I present you the BRS-AWD V2.1, different…
Note : this design has been updated to mini-reel version 3 . The mini-reel is a reel for SMD components on cut tape. It is compatible with the standard 7" reels, only smaller. Its capacity is therefore also much smaller: about 1/4th of…
It 's a remix with wider socket for WS2812B led strip. All parts and dimensions are the same like in original project.
I used 2 pieces diffuser from old LCD monitor. Cut to 321x81mm. You will need diffuser frame (without screen) from original project. I made mounting bracket to fasten matrix led down and also used as mounting hole for back cover. Two…
Habe die Abdeckung aus PETG und die Dichtungen aus TPU. Achtung! der Deckel und die Dichtung haben zusammen eine Dicke von 6mm . Eventuell muss noch ein Abstand zwischen Motor und Kettenblatt aufgesetzt werden. Print instructions Habe die…
Zum genauen Verlegen der Minitrix-Gleise helfen diese Abstandshalter für parallele Bogengleise der Radien 2a (261,8 mm) und 2b (295,4 mm). Die Quelldatei für Fusion360 ist parametrisierbar und kann an beliebige Gleisradien angepasst…
This thingy is a very basic top plate for my YiHUA 862BD+ hot air soldering station. It provides room for 6 hot air nozzles, 15 soldering tips, a spool of filament, a can of soldering flux, various diameters for tools (I store the SMD…
I have drawn up this simple box to protect the bare PCB "DIY" spot welder from possible shorts while operating with it as well as to add forced air cooling to the mos-fets on board. There are 4 separate STL files two of which will need…
This is a collection of WS2812B LED rings that I modeled in Fusion 360. If they can be of use in your modeling or just need a stand in before your LED rings come in the mail, here's the STL files I created for my project. Hope it helps…
The housing with lid is part of the Ambilight Monitor project. The case was printed with PLA. The following components are also required for the Ambilight: Arduino Nano Power supply 5V 2A ws2812b 88 LEDs (32 Top, 19 Left, 19 Right, 18…
Saya für ein Cold Steel Bokken - 92BKKC Die Saya besteht aus 4 Teilen mit jeweils 20 cm Länge. Die Teile werden über Verbindungsstücke zusammen gefügt. Ich empfehle, die Einzelteile mit Sekundenkleber zu kleben, dann kann man es im…
I changed the battery of my TT02B and the holder didn't fit with the new lipo battery. So i designed a new one. I added a vesion with an a buzzer support (battery tester) so it will buzz when the tension si too low. Print Settings Printer…
Remake of original model for rocket switch 21x15 and 5.5 socket
This is a replacement clamp/clutch piece for the ProLine LST2BK speaker stand, which has an outer tube diameter of 38mm (lower part of stand) and an inner tube diameter of 35mm (upper part of stand). There is an M6 nut and bolt that clamp…
Also check out the Case for the Sparkfun ZED - F9R
for Creality Ender 3/pro
This model is compatible with the lego system.
Some Prusa spools might be a bit too wide, especially for multicolour printing, but others have had good success with stock spools. If you are running into clearance issues, or just want to load refills onto Prusa spools, these take the…
7-Segment frame and transparant segments. Size 27 x 47 mm. WS2812B LED display behind the segments needs only one control wire for 28 segments. Arduino : Segment arranged a-g clockwise. Adafruit library. byte…
Simple and quick print (32min for 12 pieces with a 0.4mm nozzle) to hold WS2812B strips or any other LED strip with 10mm x 0.4mm size. The slot has a depth of 0.5mm, so please take care of elephant foots. I printend them in PETG Jet Black…
I wanted to replace the tracing paper diffuser with a 3D printing diffuser.
Bell Boeing CV-22B Osprey Angle Wall Art Silhouette model. Adjustable size. I accept model suggestions.
This is a chamber light mount for the Voron 2.4, 300mm. It uses standard 10mm wide, 3mm thick WS2812B type neopixel lights. Each section is 6-3/8" long (161.9mm), and is attached using two m3x8mm socket head cap screws and two m3 t slot…
Store up to six (cold) JBC C245 soldering tips, attached to the left to your soldering station. Specifically fits the profile of the C245 tips. This holder attaches to the soldering station just fine with a single M4 flathead bolt, length…
Fits Aurasound AST-2B-4 onto 120mm 8020 tracks. There are three versions to accommodate different screws for mounting. It is very important to make sure you have good adhesion to the bed as I ran into issues with the print coming off the…
A quick project to build a home automation remote control for kids. My plan is to program the included ESP8266 for sending button triggered MQTT messages to a home assistant server over WIFI. This ESPHome code is a good starting point for…
![1/4 Scale Federal Q2B Siren [BIKE BATTERY PACK!!!]](https://media.printables.com/media/prints/801fc401-0fd4-48b9-bf5f-726646484fca/images/13537966_0645e60b-61a8-420a-8f86-f0c0fb60ffb6_ee68b4ac-86d7-4417-8d1c-36218ee026cb/screenshot-2026-08-09-191803.png)
