Counting matching models…
This is a mockup of the TP4056 USB C Battery Charger Li-ion Module for further case designs sizes and dimensions have been measured carefully If this helped you, please leave a like! That's my reward and payment! 👍 I ll be happy to get…
I recently got hold of a couple of notebook batteries... ... So I needed a battery charge and test setup. I build a charger holder around my battery booklet thing: https://www.thingiverse.com/thing:4113164 This adds a piece for the TP4056…
Protective case designed specifically for the TP4056 charging circuit. Featuring a entry point for USB cable, a dedicated exit for power cables, and a secure pressure fit design. With this circuit things can get quite hot so i designed it…
In case you want to design a part that includes a tp4056 charge controller.
A holder for the TP4056 lithium Battery charging board (25*19mm). UPDATE:2018/10/01 V2 Fits most of TP4056 boards. Fits most of 18650 batteries with protection circuit. Print Settings Rafts: No Supports: No Resolution: 0.2mm Infill:…
Small case for the TP4056 charger with a window for the status LEDs.
A tight-fitting mesh for a Type-C USB 5V 1A 18650 TP4056 Lithium Battery Charger Drop it into your model and the component fits so snugly in the recess that you don't need anything else to keep it in place
This is a Li-ion charger compatible with 18650 and 21700 cells. Charges up to 10 cells. requires a 5v power supply at least 10A. I recommend 15A to avoid overheating. Each cell has its independent charging module TP4056 or TC4056. The…
This is a charging holder for a single 18650 lithium ion battery. It uses the TP4056 charging board, that you can get easy on eBay. (Search for "lithium usb charger" or "TP4056") The battery contacts used are 10x10mm but you can use…
Information SlimeVR is an open source Virtual Reality Body Tracker project. I designed this case to house some components following the SlimeVR schematics. This is my first time making a case to fit a bunch of components and the first…
This is work in progress next update will be adding an NTC for more safety. Edited 19-12-2022 : added a little how to and some Data, Features & Technical Specs After multiple prints and test I finally came with a design that I'm satisfied…
This is a vase mode print I designed to hold 2 18650 cells as well as a TP4056 charge/protection circuit & MT3608 DC-DC boost circuit. Here's the link to where I bought the circuits from. https://a.aliexpress.com/_mNJGjrV 0.2mm layer…
My own design for a Meshtastic/Meshcore Heltec V3 walkie-textie that also holds a power switch, 18650 Li-Ion cell, & TP4056 charge controller. As a bonus, everything is held together by a single M3x10 pan head screw. Bluetooth/Wifi For…
Added strain relief feature to the original design. The case is longer to accommodate zip-tie, but it's pretty minimal (4mm longer). Need re-orientation, but can print without any supports. Printing filament: Original designer called for…
BASIC MODEL: TP4056 USB - C Lithium Charge Module
designed mockup model of TP4056 USB-C charging module for representation in bigger assembly
About Quick and ugly remix to allow charging 18650 via HW-373 TP4056 USB-C module, which has larger diameters. The external dimensions are the same. Lithium Battery Charger Li-ion Module TP4056 USB C mock up was used to alter original N…
Simple TP4056 Housing. Created in FreeCAD. Ender 3 v2, Generic PLA, 0.4mm nozzle, 0.2mm Layer height.
Why charge one 18650 when you can charge up to 4 at a time! It just takes 4x as long of course. This also has a slight extension on the space available for the 4056 circuit, as the original design didn't fit the ones I have (which have a…
A little helpful file for making cases to hold either; Wemos LOLIN D1 mini V4 TP4056 BMI160 Holds these parts loosely. Handy for making a case for SlimeVR Open Source VR Trackers - Github - Docs - Schematics Option for my first test in…
For my flashlights 14500 battery I needed a charger fitting the protected version of a TP4056 because those I had laying around. So i grabbed the AA charger holder from enif and designed a holder for the charger board in Fusion360,…
Here's a Gridfinity 2x5 holder for the Klein Tools 34056 Hex Ferrule Crimper. I've also included a 2x5 5 bin Gridfinity for either standalone use or for use with the 5x4 Gridfinity Storage Box by Pred (…
Simple holder for charging 18650 batteries in original battery holder and TP4056. Be careful when pressing down the battery holder so that the cables doesn't get squeezed. The chip I use have the positive pad on the left side, please…
meshtastic heltec v2 battery case with two 18650 , back parte compatile with a famous heltec v3 case look like in photos
Do krabičky se zacvakne modul a zdířky zašroubují, vrchní krytka se zacvakne. Gcode je udělaný na všechny díly, tedy obsahuje oba dva typy krytu. Kryt bez dírky je pro kompletní uzavření, ten s dírkou je tam proto, aby bylo vidět dovnitř…
This is a replacement part for Saab 900s. This part is located at the bottom of the door card and helps secure it to the metal door. Outer diameter is 20.5mm with the inner diameter of 8.5 chamfered down to 5mm. The washer itself is 3mm…
Saw this video on Youtube before I got a printer, decided to make a more compact version. https://www.youtube.com/watch?v=bRGt_Fh9CVA&t=588s Wiring design is the same. I bought the TP4056 & ZB2L3 on Amazon, I am not recommending any…
Another LiIon Charger case. Biggest problem for me was until now, that good cotact to the LiIon battery was mostly poor. PLA is pretty brittle and not a good material for spring loads. So I decided to create a steel spring load with M4…
A simple case for 3x 18650 Batteries TP4056 charge module and a LM2596s DC-DC Step-Down converter. The top can be fixed with M3 x 8 screws
This enclosure is optimized to securely and compactly house the TP4056 charging module. The structure includes a stable base and side walls that snugly fit the board’s dimensions, preventing unwanted movement. It features precise cutouts…
Case housing ESP32, 128x32 OLED screen, TP4056 on top of ESP32 and a 1500 mAh Li-Po battery below everything.
BOM: Tp4056 type-C charger (for example https://pl.aliexpress.com/item/32930640893.html?) 1x4 2.54 male gold pin connector (remove two outside pins) 18650 batttery spring plate (i found them locally, they need to be 18 mm wide, they are…
This is a TP4056 based 20 cell charger which is to be used with a 5V 20A SMPS (for all modules charging at 1A current)
This modification of the Gameboy Advance SP battery cover incorporates a Type-C TP4056 charger module, allowing for enhanced functionality. Inspired by Makho's original design (available here ), this mod offers a sleek solution for…
Battery pack, that fits two vape cells in parallel + TP4056 module. ADJUST THE CHARGE CURRENT RESISTOR ON TP4056! Should be printed from temperature resistant filament to handle soldering (of the contacts and on the tp4056 board). I used…
Here is a charger for CRC123A/RC123A batteries, using a TP4056 charging module. I'd printed other models but found them too tight to place/remove the cells, so I designed this, giving more clearance and using springs salvaged from an…
This compact model houses a TP4056 charge model with space for a disposable vape battery at the back. Perfect for running LED fairy lights where unregulated output is fine. It can house a round vape battery, about 16mm X 16mm X 38mm.
This internal frame to hold in place the MT3608 Voltage Regulator and a TP4056 Battery Charger along with a 3.7v 500mAh Lithium Battery inside the DSO150, is designed to fulfill my upgrade needs and I hope is useful to someone else, the…
Tube Case Remix: XIAO ESP32 + SX1262, TP4056 fast charge (Meshtastic/MeshCore)
screw both part together with m3 screws loose tolerance
This model is a custom housing designed to secure and enclose a widely available TP4056 Li-ion battery charger module (03962A) for charging a Sony NP-BD1 battery. The design holds the TP4056 module in a fixed position, with a dedicated…
This is a small stand I made to mount a RAK 19003 board with a TP4056 Lithium Battery Charging control board into a HarborFreight solar flag pole. Light to use as a Meshtastic Solar Node....There are mounting holes to screw down the RAK…
Quick and ugly remix of @_KaszpiR_ 's quick and ugly remix to use one HW-373 module to charge two cells simultaneously. Please use your own wisdom and judgement when wiring the cell holders. Parallel wiring recommended!
Bluetooth DAC for headphones or retrofit old stereo . Step file available.
This is a "smart" charger for the TP4056 type C modules, it has holes for a MX2.0 connector, JST PH2.0, and classic 2.54mm headers, you are gonna have to hotglue the connectors in the appropriate holes for it to hold properly, you also…
A simple charging dock. There is space at the back for a USB-C female plug, and the output of the PCB goes to 2 Jumper Wires. There is an integrated draw to fit the battery you are charging in. The Clear lid should be printed in white to…
Stuff needed: tp4056 charging module (USB TYPE-C) 18650 battery wire PVC heat shrink (43mm and 85mm) (I suppose slightly bigger sizes will be fine too.) Heatgun or hairdryer Rubber bands (to attach cell to holder) Clear tape Possibly a…
This is a mockup of the TP4056 USB C Battery Charger Li-ion Module for further case designs sizes and dimensions have been measured carefully If this helped you, please leave a like! That's my reward and payment! 👍 I ll be happy to get…
The case accommodates two 18650 cells connected in parallel and incorporates a TP4056 module for charging. A JST-XH connector serves as the output interface. Assembly Instructions: Place the 18650 cells into the holder and connect them in…
Simple holder for charging 18650 batteries in original battery holder and TP4056. Be careful when pressing down the battery holder so that the cables doesn't get squeezed. The chip I use have the positive pad on the left side, please…
Bluetooth DAC for headphones or retrofit old stereo . Step file available.
TP4056 Type-C enclosure. For small form factor module, which has no separate MOSFET. Five pin combined IC is named R302b (DW03 IC clone?), v1008. Dimensions: 17.9mm x 14.1mm This type of TP4056 module is reaching 70-80C temperature, when…
Information SlimeVR is an open source Virtual Reality Body Tracker project. I designed this case to house some components following the SlimeVR schematics. This is my first time making a case to fit a bunch of components and the first…
designed mockup model of TP4056 USB-C charging module for representation in bigger assembly
This is a sturdy holder for a single 18650 battery and an accompanying TP4056 battery charging/discharging module. The charging module is oriented so that the USB type C port is on the bottom of the mount. I designed this for mounting in…
I needed a round electronics bay that includes a single 18650 battery and an accompanying TP4056 charging/discharging unit. I also needed the USB-C charging port to be on the bottom. This build incorporates those features. There is also a…
This is a holder for the newer TP4056 LiPo/Li-Ion charger boards with the micro USB connectors and DW01 and 8205 chips and IN/OUT pads - not the earlier mini USB with fewer chips and pads, although they may still fit or you could edit the…
This is a sturdy box with mounts for a single 18650 battery, TP4056 charging module and a micro on/off switch. The parts are designed for nearly support free printing and with layer lines oriented to provide optimal strength and…
The case accommodates two 18650 cells connected in parallel and incorporates a TP4056 module for charging. A JST-XH connector serves as the output interface. Assembly Instructions: Place the 18650 cells into the holder and connect them in…
Protective enclosure designed to fit two TP4056 modules and two AAA sized battery holders to charge two 10440 batteries in parallel. This enclosure is designed to attach together using the snap fit joints. Printing orientation is…
This model provides a small and effective box for TP4056 charger module. The box is useful, as shown in the images, the box has some space for cables on the back, collected in a single hole, in example when a JST or similar connector is…
Just print and snap the TP4056 type c 18650 Li-ion BMS module on the print. It also have 2 holes to see the charging LEDs.
This is a customized frozen slimes v1 case for slimeVR FBT trackers, for use with WEMOS D1 mini, TP4056 and BMI160 The original is designed to fit a custom PCB for connecting everything Since I don't have access to PCB manufacturing…
A TP4056 PCB Project Box Remix, that adds ventilation and active cooling - supporting a 40mm fan that can be soldered to the TP4056 for power. Using a translucent fan will also allow you to better see the charge status LEDs of the TP4056.…
A slim case for the TP4056 charging module for 18650 batteries. Features a hole on the back for exit wires/battery connection, and a form fitting opening for the usb-c on the front. This model was designed from the ground up to be fast…
This is an enclosure to house a TP4056 USB C module along with a LM2596 buck converter and a spot for an 18650 battery.
Charge a 18650 battery using the cheap TP4056 circuit boards available on ebay. There are holes in the cradle to allow a cable or paperclip to go through. This gives more stability and stops the paperclip from moving. There are also…
Bicycle front light with 18650 battery and TP4056 charger. Printed from PETG, additional parts Power LED Star 3W and reflector…
Description NOW WITH BATTERY REMOVAL RIBBON! I have used and loved enif's battery holder for years, and recently needed to make a bunch of chargers (20+) to give away with flashlight gifts when I ran across MrFlashs' battery charger model…
A compact dual 18650 charger, using cheap modules available on ebay. Modules (Get 2): https://www.ebay.com.au/sch/i.html?_odkw=tp-4056&LH_PrefLoc=2&_sop=15&_armrs=1&LH_BIN=1&_osacat=0&_from=R40&_trksid=m570.l1313&_nkw=tp-4056&_sacat=0…
This is a remix of the base and LED ring light holder for the Minecraft Ore Lamp https://www.printables.com/model/1460361-minecraft-ore-lamp-wled-esp32-d1-mini-usb-c not tested yet.
TOOLS NEEDED: ------------------------ 1 X 3d Printer 1 X Soldering Iron 1 X Phillips Screwdriver MATERIALS NEEDED: ------------------------ 1 X PCB Mount 18650 Battery Holder with Pins 2 X M2.5x6mm Flat Head Phillips Screws 2 X M2.5x7mm…
Parts used : (link shopee indonesia) TP4056 + BMS 5V USB TYPE-C 1A HOLDER BATERAI SMD 18650 1x
Route the negative wire via the bottom right corner and through the bottom hole. Solder them into the TP4056 and hot glue.
TP4056 Type-C enclosure. For small form factor module, which has no separate MOSFET. Five pin combined IC is named R302b (DW03 IC clone?), v1008. Dimensions: 17.9mm x 14.1mm This type of TP4056 module is reaching 70-80C temperature, when…
Please leave a ❤ if this helps you :) Super useful panel mount adapter for adding USB-C port and/or charging to your home projects! There is a cutting guide to place over the thing you want to install it on. Use sharpie to mark the…
bosch glm50 laser cover with 18650 tp4056 v3 bosch glm50 laser cover
--- This is a compact 3D-printed enclosure designed to house the internal power supply and audio components for a DIY Bluetooth device — such as a portable speaker. The case integrates a Li‑ion battery with a TP4056 charging module, an…
This device is used to organize your electronics. You can glue the 4056 module, solder wires and bolt down cell holders. You can also print the feet if you want to protect your table from scratches. Please do not re-upload STL or any…
This is a mount that I made for a project I was working on. It is not meant to be used as a stand-alone model, but to add to your existing project. It allows you to easily add one of these battery charging modules to your project, and…
TP4056 18650 Holder Charger the TP4056 slides in to place from the front and doesn't need any glue to stay in place. Positive Wire is about 25mm Negative Wire is about 95mm the contacts are for AA batteries and come as one piece, I cut…
this was an idea never finish it maybe it will help someone
Desgined for the TP4056 Li-Ion charger modul. You can see through the small hole on the side the current charging status (red = charging, blue = charged).
18650 USB Charger TP4056 Battery holders 10 slots TP4056 5V 1A TYPEC charger module. others， pls check screenshots
The Allen wrench (hex key) for the 40v Ryobi pole saw, model RY40560 and head unit RY40051, does not have onboard storage. This was designed to clip on the saw head portion and keep the hex key close by the saw chain. Clipping it on is…
Yet another charger housing. I found several similar things here, most are made to fit the (old?) PCB layout of the TP4056. Found few for the new PCB, but didn't really like the unprotected PCB and other detail. Now this is to be used…
This is a sled for a single 18650 holder and a TP4056. It has holes for M3 knurled inserts with an outer diameter of 4mm and height of 3mm.
Update 10/11/2024: Updated the design to include a light indicator for both Type C and Micro USB, featuring two different sizes and open cable slots for easy access. make the connector hatch more round This contains the TP4056 in a very…
just holder for TP4056 i printed it with ASA and 0.12 nozzle
The print has some flaws, but i think its still good. Feel free to improve it. Parts are meant to be printed separately I have used this socket for the battery from thingverse: https://www.thingiverse.com/thing:2892321
This is a simple shell I made for a 1A type C charger for 18650 Battery's to hide the exposed circuitry of the board. The TP4056 boards that I designed it for can be cheaply bought on AliExpress.…
TP4056 LX-LCBST type Drawn using Freecad. Easy customization by changing the value in the Spreadsheet
If you, like me, have too many TP4056 charger modules, and want to organize them using Gridfinity. I've got the perfect thing for you! The magnet holes are 6.09mm, so you only need to press them in to the holes. No glue required. I also…
