Counting matching models…
NOTE Check out the improved version of the model at https://www.printables.com/model/574794 ! I like to stress-test prints that I don't intend to “keep forever.” I used organic supports for the two smaller pieces and brim on the elbow.…
Hello there this a remix of the famous Moon Lamp for the use with WS2812B Led Strips and WLED (NodeMCU ESP 8266) to controll the LEDs. Moon Lamp Diameter approx.: 154 mm / 6 in Hole for the screwable LED Strip Mount approx.: 52mm / 2 in…
This LED strip clip should work for all 12mm width LED strips. I personally used and tested it for a WS2812b and it worked just fine. If you test other types and they work, please let me know in the comment section so i can add them as…
This model houses a WS2812 8x32 LED matrix, an ESP32 and the necessary cables. I'm using it as a status display for my PV inverter, the ESP runs Pixelix to display the contents. Most printers are too small to print the three parts in one…
Ferrari 812 Superfast Wall Art Easy to print . Of course you can scale it the size you want. Easy to print for up to 110cm length, just cut it in some parts with the new slicer. I recomend a strength of about 2-3mm. Add some double-sided…
UPDATE: I also have done a 32x32 Matrix in a IKEA picture frame with WLED: https://www.printables.com/de/model/501107-led-rgb-matrix-ws2812b-esp32-wled-32x32-round-squa…
This is a jig that can be used when soldering round SMD mounted WS2812 LED using 24 AWG Magnet Enamel Wire I created this jig to assist me in soldering magnet wire to pre-populated WS2812 LED assemblies. The jig will hold the LED in the…
This is my custom design for battery holders for 38120 LiFePO4 Battery cells.These parts can be used to make any arrangement of 38120 Cells in any series or parallel configuration! For my specific project, I made a 4S 8000 mAh battery…
This is a silhouette model of the car. The default stl is approximately 40cm and 2mm thick. You can scale it as you like in your slicer, but don't scale it uniformly, otherwise the thickness will change (try to keep 2-3mm). Add…
A NeoPixel / WS2812b controlled LED Matrix with 16x16 Pixels Easy to print: Can be printed without support, Filament Type doesn't really matter. I printed mine with PETG, but PLA or something else should work fine as well! I printed the…
Hello Makers, i wanted a bigger LED matrix with 32x32 LEDs. So i looked for a nice picture frame that fits also for the depth. I found a good & cheap one on IKEA. On Youtube there are lots of tutorials to build a 32x32 matrix out of four…
I found a great tutorial for electronics that was missing only the case. So I started modeling. Many thanks to Crazymakers for their work and sharing. Link to the video : Link to the website :…
I needed a simple clock in one room, so I designed one. 24h display to be equipped with WS2812B LED-Strips with 60LEDs/m. Each digit will need 15 LEDs, two on each segment with one LED hidden between to segments. I did a lazy wiring job,…
Here's how to build a simple RGB LED cube using cheap 8x8 WS2812 / Neopixel LED panels. The design is a single 3D printable piece, printed four times, that screws to the panels and forms a frame to hold them in place. Parts Needed: 4 x…
I made wire channels a little wider to accommodate thicker wires (24 / 26 AWG). I also removed part of the edges surrounding the LED so that it is easier to rotate the LED around to position it just right. Removing that material also…
LED diffuser grid for ws2812b strips (60 leds/meter) display. I would recommend to print it 0.2 layer height, print the 3 first layers with white PLA then change filament to black. Pictures are from 4 8x8 grid glued together for a 256…
Print it laying down. put the leds in the slots and wire it up. diffuse it from the front side
Hi, so I had some of these 8x8 LED Matrix panels laying around here and wanted to do something with it. I found the awesome matrix project from blueforcer which is open source. I wanted to use these 8x8 panels from CJMCU. Due to the…
Two methods for fixing the channel , holes along the center, and tabs on the side, these are 190mm long. I printed these in PLA, flat on the bed with supports everywhere, might get away without supports I didnt try. The led strip I used…
US Navy Cutlass, as wielded during the war of 1812. https://www.history.navy.mil/research/library/online-reading-room/title-list-alphabetically/u/uniforms-usnavy/swords.html…
my son lost this part while building some cool original lego technic monstertruck (thanks to the LEGO company), and i was irritated not to find it somewhere here. luckily 2 were used in the model, so i started to reengineer it . the angel…
Just another seven segment LED clock. Current version of SW working, but it isn't final version. What is working: time on dislpay synchronization from NTP server time in local time zone. This zone must be specified manually on source code…
Remix (resize) case for Generic 8 x Neopixel (WS2812b) Stick / Bar - Case - WS2812b-8 Support me at: Buy Me A Coffee Original model did not fit these generic Neopixel 8 Bar / Sticks I found on aliexpress, had to resize. Aliexpress Amazon
RGB matrix case Diffuser (print in place with color change) Case stand Back frame to fit esp32 dev boards, mini bread boards, etc Printing Instructions Please use white filament for diffuser. The case & stand can be printed from any color…
Wordclock Matrix 11x11 Frame for WS2812B LEDs. LEDs can be simply clipped into the frame. For the Wordclock Frame i use a IKEA Ribba 23x23cm Frame https://www.ikea.com/at/de/p/ribba-rahmen-schwarz-40378401/ Source Code for this project…
custom LiFePO4 battery based on headway 38120 HP cells .Cells are 8AH with 200A discharge rating .Be extra careful while handling those cells . I got the cells and bus bars from batteryhookup.com . nominal cell voltage is 3.2V , 4 cells…
This is a simple mount for 10mm wide WS2812b (often known as neopixels) to mount along 2020 extrusion. It mounts the LEDs in parallel to the extrusion profile used. 100mm and 150mm lengths provided, as well as a .STEP and Fusion 360 file…
Pictures are of V1 STL files. I've printed but still need to solder the V2 STLs based lamp. V2 lamp uses 5-12 LED strips placed horizontally on the lamp - significantly reduces the amount of soldering! As well, the button has been moved…
I remixed the Superfast model to print on its side with the wheels and axles built in. Print as oriented, no supports, if slic3r doesn't import it correctly use Cura. See my collection for more cars:…
I have downloaded this file, and it did not fit the Siboor led lights I had purchased, Since I printed them on ABS, as it shrinks by around .5% on this long piece it was 2mm too short, so it was remixed with those tolances in mind, and…
LED diffuser Matrix 8х8 WS2812 Simple printing from the table upside down. Nozzle 0.5 layer height 0.2
The clock is based on WS22812b addressable LED strip and WEMOS-D1 mini (ESP-12F) board. In my case it is running the ESPHome software in combination with Home Assistant (see link below). Fusion 360 files are also available. To get result…
Version 2.0 now ready for download. The charging unit now snaps in preventing the unit from falling out. This is a Makita Battery Charging Stand that tilts the charger at a more user friendly angle. It was designed for the 48-59-1812…
Embrace the pinnacle of Italian automotive performance with this 3D printable STL model of the Ferrari 812 Superfast. This exquisite supercar replica is perfect for automotive enthusiasts seeking to display the breathtaking design and…
3d printed Connector for jumper wire 12mm Dupont as soldering aid. Find out everything you need to know about the connector on my blog: https://nerd-corner.com/printed-connector-as-soldering-aid-for-jumper-cables-and-led-strips/ 14mm…
The LED holder on the floatbox site does not fit sk6812 LED strips, which was my preferred choice of strip for this build. SK6812 has excellent output since it has a dedicated white channel. I've altered the interior slot to accommodate…
separated diffuser for 8-bit stripe with 5050RGB chips
The simpliest LCD Neopixel wheel holder there is. Used for Neopixel LED ring WS28128B
An Awtrix 3 case for a WS2812 64-bit LED matrix is typically designed to house and protect the components of an Awtrix s
I have been having a hard time soldering the LED with the jumps due to many movements that make me solder my hand with the table. None of the solutions that I found were proper to my case, I wanted something straight forward that holds…
The first version published here is a rather minimal case with a surprisingly effective diffusor for one of those quadratic LED matrices you can get on Aliexpress with 256 WS2812b LED on it, 16 rows a 16 lights, spaced in a 10mm raster. A…
Raspberry Pico USB-C WS2812 clone snap-fit case. OnShape: https://cad.onshape.com/documents/cf6759dd1f144a7bfcea9e13
I had a bunch of WS2812B modules lying around so I decided to make this gear/flag display. If you don't have any of these modules you're probably better off ordering a 8x8 matrix and using that instead as there's less soldering to do, but…
This replaces the LED and switch mount for MAME KOF American Type Push buttons. Video example: https://youtu.be/QJ1OX\_ZHtn8 Buttons: https://www.aliexpress.com/item/33001974422.html LEDs: https://www.aliexpress.com/item/32960205936.html…
It 's a remix with wider socket for WS2812B led strip. All parts and dimensions are the same like in original project.
I used 2 pieces diffuser from old LCD monitor. Cut to 321x81mm. You will need diffuser frame (without screen) from original project. I made mounting bracket to fasten matrix led down and also used as mounting hole for back cover. Two…
This model is compatible with the lego system.
I needed a few trim clips for my E30 and didn't want to order them. Prints well in PETG or stronger material. Also, print sideways for strength and add support material
Showcase your custom pixel art, scrolling text, and dynamic animations with this sleek and versatile enclosure, designed specifically for a flexible 8x32 WS2812 RGB LED Matrix. This case provides a sleek and professional look and durable…
Printed for Ping Pong Balls and Gardena Microdrip may be any other 3/16" or 4.6mm tube. You need 92 LEDS and PingPong Balls for hole sphere. 12 Parts 5 Arms with 16,5mm Gardena Tube Slices and 80 Parts 6 Arms with 27.5mm Tubes. You can…
This is a collection of WS2812B LED rings that I modeled in Fusion 360. If they can be of use in your modeling or just need a stand in before your LED rings come in the mail, here's the STL files I created for my project. Hope it helps…
A spacer for Gaggia Grinder RI8123/01 MD15 This is a spacer u can easily put in the top part of the grinder between the plastic and the metal cylinder. just unscrew the two little screws that keep the two parts together and place it in…
The housing with lid is part of the Ambilight Monitor project. The case was printed with PLA. The following components are also required for the Ambilight: Arduino Nano Power supply 5V 2A ws2812b 88 LEDs (32 Top, 19 Left, 19 Right, 18…
Adjusted with PrusaSlicer, so it may not be pretty, but it just works. -You may need to hold the right side down as you screw in to prevent the print from twisting. -The right screw threads into the print. Refrain from over threading.…
his is a fully 3D-printable 6812 deep groove ball bearing designed to use 6 mm airsoft BBs as the rolling elements. It’s meant for light-duty applications, experiments, or just as a fun demo of how bearings work. I’ve tested it in PLA,…
7-Segment frame and transparant segments. Size 27 x 47 mm. WS2812B LED display behind the segments needs only one control wire for 28 segments. Arduino : Segment arranged a-g clockwise. Adafruit library. byte…
Simple and quick print (32min for 12 pieces with a 0.4mm nozzle) to hold WS2812B strips or any other LED strip with 10mm x 0.4mm size. The slot has a depth of 0.5mm, so please take care of elephant foots. I printend them in PETG Jet Black…
A battery cover for the Bosch Theo Klein Kids Vaacum. When your kid drops the toy the battery cover can break easily. We have two of these and the cover is broken on both.. but this print is much stronger than the original.
I wanted to replace the tracing paper diffuser with a 3D printing diffuser.
This is an original adapter plate to allow mounting an Ali-Express 2.5Gbit RTL8125b adpater to the HP Mini's FlexIO V2 slot Designed it to mount the socket upside down so it better aligns to the slot at the rear of the HP mini. Also have…
This is a chamber light mount for the Voron 2.4, 300mm. It uses standard 10mm wide, 3mm thick WS2812B type neopixel lights. Each section is 6-3/8" long (161.9mm), and is attached using two m3x8mm socket head cap screws and two m3 t slot…
Modular design approach to a stackable andon light using commonly available flexible WS2812 (or similar) LED strips. LED spacing is 16 mm. Great as a status indicator for machines, though not necessarily for industrial purposes. Module…
A quick project to build a home automation remote control for kids. My plan is to program the included ESP8266 for sending button triggered MQTT messages to a home assistant server over WIFI. This ESPHome code is a good starting point for…
Highly detailed. 1 meter consisting of individual LED segments. Can be combined to the length needed
runde Neopixel Uhr https://youtu.be/7\_WXX9sdJPA benötigte Druckteile (schwarz oder andere "nicht transparent") 4x Oberteil 4x unterteil 1x Aufhänger 12 Uhr 1x Stützer 6 Uhr 2x Stützer 3+9 Uhr 1x Halteklappe (klar / transparent) 12x…
IT IS STILL A WORK IN PROGESSS, it works, but i wish to add more improvements. I will continue as soon i will have time, i have just moved home after 3 years, there are more important things to get done around the house. Plus new…
Make this from any kind of filamant as long as it is white and lets the light shine through.. You need to buy the pre-mounted LEDS in a ring from ebay or any Chinese supplier, program an Arduinop nano and get a clock module attached to…
I add the WS2812B LED HW-335 circle 3 bit module
Lötstellen Sicherung, für einen WS2812B Pixel LED Streifen, 3 Pin, 10mm Breit (innen) 12,6mm Gesamtbreite 4 mm Hoch 17mm Lang
This is an update to the simple diffuser to clip onto a CJMCU-2812B-16 Pixel WS2812 led ring. I increased the outer radius so the 0.9 mm outer shell fits over the ring. With my print settings it fits nicely and doesn't need any glue. I…
Based on the incredible nice looking Jack O Lantern I remixed a version that changes the 3 original LED's for a fully wifi controllable battery powered version with WS2812 LED's. The led's change brightness/are flickering like a candle…
I have already seen such a lamp a few times and thought it was great. I still had a aluminium profile, a WS2812 / LED strip and the power supply, so I designed myself a base and assembled everything. The "intelligence" is based on a…
Model has two options: with spoiler and without.
A 8x8 LED matrix as a printed LED word clock. Print the first layer or two layers of the top with transparent or translucent white, you could also add some layers of an another color, if you want a coloured appearance. The rest of the top…
Exactly the same, just modified to hold 2 more matrix screens for a total of 8x24 matrix grid. Use with iFlag as Simhub doesn't support multiple matrix's paired together. WLED also works really well with this.
Print the first 2 layers with a translucent material and the rest whatever you desire. You could print the entire thing in a translucent material as well. I used a PLA/Wood Fiber blend. This was designed to diffuse the LEDs in a 16x16…
reduced size of original for smaller led matrix
Крепления фар Audi A4 B7 8E0998122B
This is part of a bigger project, probably will add the other parts bit by bit.
I have seen some 16x16 WS2812 pixel matrix on Aliexpress.com and coul not resist to buy it and make something with it. So here is my creation, 16x16 WS2812 LED matrix panel. I have created some stand for that as well but i think it could…
Fibonacci256 is a beautiful 166mm circular disc with 256 WS2812B RGB LEDs surface mounted in a Fibonacci distribution. Fully open-source software, and programmable over Wi-Fi or micro USB cable. Buy from Evil Genius Labs:…
A small case for the ESP-01S WS2812 RGB LED Controller Module . All hail the Aircoookie !
holds one D1 Mini V3 NodeMCU ESP8266EX
The moment I saw the Prism Tower I knew I had to remix it ! This version is made for up to two buttons, 6x WS2812 and a Wemos D1 Mini. A wiring diagram and maybe some sketches will follow soon. Category: 3D Printing
Сетка для адресных диодов 16х16 с подключением к ESP8266 Node MCU Category: Electronics
Here is a holder for a WS2812 LED ring (12 LED). Optionally, a bracket for the holder for an Ikea Lack table is also included. The whole thing fits perfectly with the Octoprint LED status plugin. The screw holes are optional and…
This is my design for a 91mm tall by 84mm diameter hexagon patterned WS2812B RGB LED array, touch controlled, lamp. The LED array is 5 horizontal strips of 12 WS2812B RGB LEDs at 60 LEDs/m. I've used vase mode printing on the outer shell…
WS2812B 10001000 You are heavily addicted to addressable LEDs? Then this is the right coaster for you. Or use it as a deco object on your workbench. The package is 10001000, so 20 times larger than the original 5050 WS2812B. Equipped with…
BL-M8812EU2 cooller case; radiator: aluminum 35x35x10mm cooler: 30x30x10mm 12v with txpower 45 it heats to 42 degrees
A simple design for a mount for WS2812b (neopixel) LED strip for the Sapphire Pro. The holders are mounted on the left and right side ot the printer, via T-slots (M3), at the height of the motors. The beam angle is 22.5°. 2 parts per…
Parts used: 1x ws2812 led ring with 24 units 1x esp01s 1x ws2812 esp01s to ws2812 adaptor unit Firmware: ESPHOME Configure the led ring with neopixelbus Here is an example that works:(Only the light section of esphome configuration file)…
Gantry mount that adds a WS2812B LED to the gantry of the Sovol SV06 using the screws used to mount the hotend to the gantry. Printing Layer height should be fine (≤ 0.2mm) to properly trap the LED, but otherwise prints fine with a 0.6mm…
I adapted the models made by Sergio Morales to match my need. I didn't want to have to use an ESP8266 (I wanted to use an external ESP32 running ESPHome). I added holes for easier wiring through the back of the digits instead of running…
Einfaches Modell, aufrecht ohne Stützen zu drucken. Links Halter für Eurostecker, rechts Halterung für Ladestecker, vorne für Kabel. PLA ist normalerweise ausreichend. Simple model to print upright without supports. Left holder for Euro…
Printed with Prusament PETG Orange 0.3mm for the bottom, 0.2mm for the top no rafts or supports required. Alieexpress ring:…
This is a LED Ring housing for LED Ring with 24 LEDs (86mm). Can be used as watch or notification light if powered over 5 Volts(USB) and controlled by ESP8266. Designed with hole for wall mounting. Hold together by a four pin design.…
Hello, This model is a replacement for fiat plug. I have tested it on my Alfa Romeo 159 and it went in perfectly. Feel free to use it for personal use if needed. They don’t cost much but printing on your own makes it even better. I’ve…
This is a socket for SK6812 Mini-E RGB LEDs which come in a tiny SMD package. In contrast to the SK6812 ( socket can also be found on printables ) it is much easier to solder. This socket helps soldering wires to it, provides strain…
This is a re-created version of KTM/Husqvarna "Marking Mandrel" Pt.# 78129032000 intended for timing the balancer shaft when re-installing the side case on a KTM 450/500 or Husqvarna 450/501. Here's a YouTube video explaining the process:…
Practical and fast, it allows you to connect several strips together or create simple joints in curves or decorations, the only limit will be your imagination. For their use You will need: Led strips WS2812 1 x fast connector 1 x clip…
