148 models
About Voron V0 Auxiliary Fan Ducts These are auxiliary fan mounts for the v0, which you can use if you need extra cooling on your Speedbenchy journey. The ducts can be easily installed after the Printer has already been fully assembled,…
Cover your fan in style with the Auxiliary Fan Cover for Snapmaker U1! Featuring a Snapmaker logo, and hexagons (the bestagons).
Update: Added step file to make remixes easier. Please do no sell derivatives of my design. It started free, it should remain free. Update 2: Added the caveat that the duct is quieter on my machine . Its possible that my stock duct,…
About This adds a 120mm auxiliary cooling fan to Voron Trident 3D printers. This is heavily inspired by the VzBots RSCS cooling fans. The cooling is mainly targeted at the center of the bed (around 150-200mm wide air stream). No…
Redesigned from scratch to have a more evenly spread airflow and a way to print it without any support.
*Use the excact .3mf file has been uploaded to print this case to obtain a perfect air duct surface. (the support has been set, Please do not change the sliced file) *Printed in ABS (or other materials with good heat resistance, Do not…
A fan cover/grill with various patterns to prevent filament scraps from being drawn into the fan. ⚠ It is recommended to use PETG or a material that can withstand higher temperatures. BENEFITS: Protect your auxiliary fan from filament…
Remixed from the No Support design of Yodog I acquire 2 New K1 Max, and it seems that the Side Fan has been Updated on the Latest Models of 2024. So, the prior design doesn't fit the Updated Side Fan air exhaust part, I remixed it to fit…
Print with PLA Support and Brim not necessary (if then use tree support) 15% Infill (for better material stability use gyroid infill) To look better use the Arachne wall generator Thanks for downloading in advance and please don't forget…
You will need 12032 fan (basically 4 pin, but also you can use 2pin with config edit), some nuts and screws to attach fan. I mounted the fan with a double sided tape. The only tricky part is to mount upper part. It must be about 1.5 mm…
A k1 auxiliary fan (side fan) sound reducer, and guard the fan from trash admit.
My Flashforge Adventurer 5mPRO had the standoffs and a brim on a right wall. So i thought it was for a second aux fan. But the original duct did not fit. And i modeled my own. I used the top part from the trident model extended it, and…
After enclosing my AD5M, I wanted to add a fan for various reasons which we all have. Anyway, I found a fan duct I liked because it fit snuggly in the fan I purchased specifically for the AD5M. The wiring was correct and everything fit…
This holder alows you to mount the X1 Auxiliary Part Cooling Fan on the P1P. The P1P version of the Auxiliary Part Cooling Fan was not available in the bambu lab shop when i purchased my P1P. So i bought the X1 version of the fan. I based…
Circle-drawing auxiliary tool (Rotio Compass)
As I often hit the fan and because of the dust that accumulates, I've decided to realize some Covers for the Auxiliary Fan . If you like it, take a look at my other 3D printer accessory creations . As you can see from the photos, there…
"Breeze" is a simple auxiliary fan system for the Voron 2.4 printer. You can mount up to four 5015 fans on the gantry (two on the left and two on the right). This allows to increase part cooling capabilities, which is useful especially if…
This tool is a auxiliary tool for grinding drills with a proxxon TSG 250/E plate grinding machine. The tool is inserted into the rail so that the angle matches the drill. For easier printing, the template is divided into two parts
Воздуховод для бокового вентилятора Qidi Q1 Pro. Я случайно сломал лопасти на родном вентиляторе и мне не удалось снять родной воздуховод. Я спроектировал свою модель и готов поделиться ей с вами. Я так-же загрузил файл для SolidWorks.…
Remixed from the great design of Gonzos_Gizmos I strechted it to 74.5mm to be the exact height as the stock auxiliary fan position, also made a side cut for an accurate stock bracket camera clearance.
This is an electrical connector to allow a non Anker Battery to be used on the F3800 battery unit. NOTE: This is NOT UL Listed, Not Approved by Anker! The reason that I created this model is because I have seen others successfully connect…
Hello! Here is a remix of the Voron Trident Auxiliary Fan made by @JacobG3231_143196 , making it compatible with the RatRig VCore 4. Please refer to his model for the BOM and assembly instructions. The extra parts required for this remix…
Since i wanted to print a special part on my XL, and FAILED multiple times. I experimented, and it seemed that this was caused from missing part cooling. Ive been designing and modifing this Side covers (Pre- prepared for Enclosure), with…
Auxiliary products for Airbrush, suitable for Vallejo.. Positions for 1x200ml, 5x 60ml, 2x32ml, 1x17ml bottles, 2x hole for cotton buds or tampons and 3x positions for brushes, scalpel, etc. The vents are only decorative, they have no…
Bambulab X1C Auxiliary Fan Cover Hex with logo
Auxiliary cooling fans for V0! Keeps a nice thin sheet of air flowing just below the nozzle. Can be used to heat up chamber when bed is high (door and tophat closed), or to cool down the bed (door and tophat open). With the arctic fans…
The original upload only contained a single .3mf file. I opened it with PrusaSlicer and exported each of the 3 components as individual .stl files. No other modifications were made. Duct should supposedly be printed in the orientation…
I noticed that when cable chain is added to the print head, it sags a bit and rubs the wire that powers the auxiliary fan. Even though I taped it down to have the lowest possible profile, the chain was still hitting it, so I decided to…
Auxiliary spool pin for Singer sewing machines
The auxiliary fan of the Bambu Lab X1 3D printer is glued to the side wall. On arrival of the printer, the fan was loose. So, I decided to design a fan holder to be screwed to the bar where the LED is attached. When installed, the fan…
Note, see the remix of this model by Mike Wil for 15mm thick filters rather than 14mm filters, and with even more clearance from the z-blocks than the V3 version if required. V3 - A user reported that the V2 clashed slightly with the Z…
120mm auxiliary part cooling fan designed for a ZeroG Mercury One.1 370 (Non-Hydra) that may also work for Ender 5 and 5+'s. The ducts have optional heat set inserts for strength. You need to close the holes if you don't use the inserts.…
Auxiliary Fan Duct using 12032 fan, Same as the k1 / K1Max Remix From https://www.printables.com/model/692486-voron-v02-auxilliary-fan-ducts-12032 SV05 Auxiliary Fan Duct using 12032 https://www.thingiverse.com/thing:6502244 SV05…
Didn't find any fan cover for K2 Pro on the internet when I made this. Print with filament that can withstand some temperature.
here is my take for an auxiliary fan for my voron 0.2. i had trouble with printing PLA in the enclosure, because of insufficient cooling for the parts. the mini stealthburner couldn't provide enough partcooling for PLA. i designed the…
Printed with Esun ABS+ (PLA is not recommended, it's close to the hot bed) and mounted with 2 screws M3x14mm.
I've deleted my previous designs of the IXO Auxiliary Head Wall-Mount and uploaded a remake of them. if required, I can add further combinations like a single mount also. 3 piece holder 4 piece holder same design base for all of them…
Search Creality Auxiliary Fan on Amazon if you don't have one and you want one. with the duct, it's the best option for Enders, since the fan speed is adjustable from the fan. Just not with software, unless you are good at that stuff.
I added a custom headlight to one of my ATV’s and I wanted it to have a fuse. I plan on adding some other thing's so I made an auxiliary 3 circuit fuse box that uses standard size atc fuses and blue female spade connectors. Crimp on the…
With this tool you can cut cardboard, paper or similar material straight. Slots are placed on the tool at a distance of 5 15 25 35 45 mm so you can easily adjust the desired cut on your material Printed on Prusa MK4 0.2 layer PLA 40 %…
Lengthened it 8mm so it sits lower, for use with a volcano block or a volcano adapter.
"Breeze" is a simple auxiliary fan system for the Voron 2.4 printer. You can mount up to four 4020 fans on the gantry (two on the left and two on the right). This allows to increase part cooling capabilities, which is useful especially if…
Description This flexible plug is designed to seal the auxiliary feeder cord pass-through hole on the right side of the Sovol SV08 Max enclosure. Printed in TPU, it provides a snug, adaptable fit that helps maintain chamber integrity by…
I design this secondary chamber LED bar (it reflects the original design),so you will have more lights inside the chamber without needing to print a riser. To light up the LED bar you can user jumpers to connect it to the original 2 pins…
Thanks to LimeThemUp for the original work and providing the step file. I could not get the V3 right and left ducts to fit in place. They were too deep to fit between the side wall and the z rod mounts on my machine. I took .75mm off the…
I've designed this light some time ago for the build of my 3Dsets FJ40, but never managed to publish it. Back then I made two versions, one with a flange mount and one using a single screw on the bottom. When I bought my Vanquish H10…
This model is an improved version of the stock and existing designs; it does not obstruct the camera, and the foot parts fit perfectly with the blower section. As this is the first model, I am aware of some issues, and a new version will…
A modification to the 7530 aux fan to fit a 7020 blower from a projector that I had lying around.
Вариант усиления консольного стола FlyingBear Ghost6 дополнительными валами и двигателем оси Z. Основное преимущество - шкивы и ремень располагаются внутри принтера. Другие особенности: Область печати уменьшена на 3мм. По задумке область…
Remix of bowilab's Thing:1616985 Just added two holes into it. Category: 3D Printing
Flip around the 60mm exhaust fan that does very little and turn it into a light duty auxiliary blower fan. There is 5mm offset from fan center so make sure it points slightly upward during install. Requires at least 2 additional m3 screws…
Ducts for 120x32mm blower fan. Based on Sentinal nozzle height. Clearance for bed frame. Mount with. x3 - M3 x 8mm x3 - M3 T Nuts x3 - M5 x 8mm or M4 x 10mm
A custom fan shroud that converts a Nevermore V6 into an auxiliary cooling fan for Voron V0 printers with Dragon Burner toolheads. The shroud is printed as two separate parts (A and B) that will fit the V0 bed which are later glued or…
Modified the top fan shroud and bottom fan mount. Either mount the fan low or high in your +50. Extended fan shroud uses stock base and top mounts. Extended base uses stock shroud and top mounts.
These allow the use of hose clamps to attach auxiliary lights to the bars of a bicycle / motorcycle or ebike. They use standard size hose clamps. This is the listing for the lights…
Diese Figur ist ca im Massstab 1:35 und ideal für Resin Druck
2023/4/24 更新：V2版本 改進外殼卡榫的固定孔位 除去支撐需求 縮減電池預留間隙，減少電池晃動 增強螺絲柱的強度 可裝四或八顆 18650 電芯。可裝進 gogoro 原廠小電池外殼，並且符合內部的卡榫位置。螺絲用原廠電池支架上的即可。 列印方向如圖七所示，不需支撐。線路圖如圖八所示。 原廠使用來自「山東精工」的 HTCFR18650-1500mAh-3.2V 電芯 請務必使用 3.2V 磷酸鋰鐵電芯！ 接頭為 04R-JWPF-VSLE-S，更換電芯不會動到…
PETG, 5 walls, no support. It is necessary to use a little force to fit the rollers
Inspired by 247zero beta1, this auxiliary fan unit is guaranteed to destroy your eardrum. Has a smooth interior instead of 247zero's square shaped hole. Ideally print with 2 outer walls and use a height range modifier to change the first…
i wanna add a Aux cooling part to my Anycubic 4MAX but i didn't wanna buy a regular 120mm blower when i have more powerful alternatives laying around , so i took a Dell CPU cooling blower for an old OptiPlex 790 series and modify one of…
Flying Bear Ghost 5 Auxiliary Fan
Auxiliary fans won't fit with the Matchstick strip, this modification allows fitment for both. Original creation: https://github.com/JackJack3231/V0-Auxilliary-Fan Follow the original guide for installation.
Now you can control the auxiliary light on the printer over the application (BambuStudio or Bambu-App) or directly in the printer. Uses the power of the original light on the printer as a trigger to turn the auxiliary light on/off. Here…
Motivation I wanted a way to draw heated chamber air for the auxiliary part fan instead of cool external air. There is not much space to work with but I managed to fit in a new fan intake that uses the existing fan screws. Printing I…
This is a quick remix of JackJack3231 's Voron V0 Auxilliary Fan Ducts that allows a 12032 fan duct to work with most if not all “Printers for Ants” Voron V0 variant designs by eliminating the clamp and mounting the fan duct from the top…
The popularity of auxiliary fans in enclosed printers like the Bambu X1 or Creality's K1 made me wonder of how I could implement something similar with my MK3s+ / Lack enclosed printer. I've included the step files for the duct and mount.…
Center section, scaled in Z to work with XOL UHF this orients the ducts perfectly in line with the nozzle area on my xol on a Trident 300 with 250ish zheight without blowing all air against the ducts in the first couple layers some of the…
This remix is based on jp0221's Pharmacy Label Tape Holder 2 & 10 Slots. While this was great, I needed some in-between sizes so I created a 4 & 6 slot holder. It was created to hold the rolls of labels for pharmacies. Designed around…
Made For A 4020 Blower Fan How To Get All Needed Parts Go to Auxiliary Fan Then Go To The 5015 Folder To Get Everything Needed Credits To @JacobG3231_143196 Also if you are wondering what the small fan with the voron logo is it is a…
This is an auxiliary light intended to be used on a Bambu A1 Mini to assist in viewing the nozzle. The A1 Mini has a light but it is up higher an does not get a lot of light to the nozzle area. This light sits on the right side of the…
The detachable Spool Pin for the Singer 500J & 500A series sewing machine Aka, the Rocketeer Sewing Machine
This is the same model as the original fan ducts, just without the extra heat set insert holes that aren't used for anything
Needed to have something to mount auxiliary lights to the crash bar of my Honda NX500. They needed to fit the 3" Nilight Light Pods to the bars with a 145° inward, and 170° downward angle. I ended up with this design that accommodates the…
This part prevents print debris from getting into the auxiliary fan on the side. Designed for X-Plus3, but should also fit X-Max3. PETG or ABS is recommended; avoid PLA. 3-pattern designs are available, as well as a no-mesh type for…
Early Kickstart-era Bambu Lab X1/X1Cs featured double-sided tape to mount the fan to the inside of the case shell instead of screws in later builds. After doing a repair, I found it difficult to get the new double sided tape to stick the…
So I finally got to a point where I'm hitting a really hard to crack cooling issue on my Sovol SV-05. Even with a 5015 and a directed duct, I cannot get sufficient air on PLA for 300mm/s printing. Inspired by the auxiliary coolers of the…
Made this aux. carbon filter for my q2. Printed mine out of ASA. No inside brim! I am using carbon pellets from Amazon. 4- 25mm lg x 3 mm screws, 4- 6mm lg x 3 mm screws. Make in 3 pcs.
Most 12V splitters on Amazon didn't come with caps. This should remedy that, and they'll even stay on the cable! Will keep water out, but I wouldn't call it waterproof. Print with something flexible like TPU. The strap needs to flex…
Modular Cassette tapes rack -- Auxiliary Module 02. >_ The Tape Matrix is a modular containment system for high-density organization of analog sonic relics. While these frames provide the structural foundation, the system is designed to…
Modular Cassette tapes rack -- Auxiliary Module 01. >_ The Tape Matrix is a modular containment system for high-density organization of analog sonic relics. While these frames provide the structural foundation, the system is designed to…
It's a mod for the VZBOT 235 that allow to use 120X30mm fans as auxiliary cooling which allow a better airflow.
Accessory for the Bosch IXO attachment head for storage on a Skadis multi-board wall For four tool heads The idea came from Printables. Originally intended for screwing, I wanted a holder for Skadis. I also modified a holder for the Bosch…
Adds additional lighting to the K1 with an integrated space for a 10mm 24V LED strip added to the auxiliary fan. Fits onto a standard K1 12032 fan. Requires an M3 heat insert to allow for screw.
I've added accessory switches to my Harley. The official name is "Auxiliary Accessory Switch Housing Kit" It has locations for three switches and comes with two blanks, assuming you're installing at least one switch. Cool. I lost one of…
I designed an auxiliary fan for QIDI X-CF Pro It use a 120mm blower fan. Hardware required: 4 x 12mm M3 bolts 3 x 8mm M3 bolts 6 x M2 self taping screws It will replace the original ventilation fan position. You need to drill to expand…
Modular Cassette tapes rack -- Auxiliary Module 03. >_ The Tape Matrix is a modular containment system for high-density organization of analog sonic relics. While these frames provide the structural foundation, the system is designed to…
Modular Cassette tapes rack -- Auxiliary Module 06. >_ The Tape Matrix is a modular containment system for high-density organization of analog sonic relics. While these frames provide the structural foundation, the system is designed to…
Modular Cassette tapes rack -- Wall Fixing Modules. >_ The Tape Matrix is a modular containment system for high-density organization of analog sonic relics. While these frames provide the structural foundation, the system is designed to…
No supports needed to mount the fan you can use screws or like me doublesided tape simply atach the whole thing to the axis
JETPACK JETPACK is a fan that attaches to the back of the X gantry on your Ender-style 3D printer. It’s flexible and can be adjusted to fit different toolheads, improving cooling and print quality. Hardware required: You'll need 3x 5015…
Modular Cassette tapes rack -- Auxiliary module 11. >_ The Tape Matrix is a modular containment system for high-density organization of analog sonic relics. While these frames provide the structural foundation, the system is designed to…
Modular Cassette tapes rack -- Auxiliary Module 05. >_ The Tape Matrix is a modular containment system for high-density organization of analog sonic relics. While these frames provide the structural foundation, the system is designed to…
Modular Cassette tapes rack -- Auxiliary Module 04. >_ The Tape Matrix is a modular containment system for high-density organization of analog sonic relics. While these frames provide the structural foundation, the system is designed to…
Modular Cassette tapes rack -- Auxiliary Module 09. >_ The Tape Matrix is a modular containment system for high-density organization of analog sonic relics. While these frames provide the structural foundation, the system is designed to…
Modular Cassette tapes rack -- Auxiliary Module 12. >_ The Tape Matrix is a modular containment system for high-density organization of analog sonic relics. While these frames provide the structural foundation, the system is designed to…
After a sealing ring of the rear auxiliary heater of my VW Multivan Bluestar failed, dumping the entire coolant into the carpet, I removed the unit. Obviously, I want to protect the plug to be able to reinstall the unit, if I ever want to…
Modular Cassette tapes rack -- Auxiliary Module 07. >_ The Tape Matrix is a modular containment system for high-density organization of analog sonic relics. While these frames provide the structural foundation, the system is designed to…
This model is a compact, stackable storage box designed specifically for the BM-RS caliper . The internal layout includes a 2×6 main compartment grid for secure tool placement, plus three additional side compartments for accessories such…
