Counting matching models…
This is a remix of the original BoxTurtle part. It allows you to use a CLINKO M12 connector for the cable that runs between the BoxTurtle and the printer's main board. It's up to the builder to work out the details, but my planned…
Not sure how I wanted the skirts for my 🥰 BoxTurtle , whether to go the true mesh way or rather opt for a mesh-like look only but have them printed solid 🤔, I played around in CAD to have the mesh as a separate part and also to do some…
The 🥰 BoxTurtle Enclosure comes with a redesigned front and different skirt parts which require some changes to the TurtleFence . So here they are: Modified front skirts, spacers and the clip-in mesh inserts to fit the enclosure … and of…
Tired of your BoxTurtle filaments sitting out in the open? I designed this simple adapter to give mine a proper home inside a Sterilite tote. It's a cheap, easy upgrade that keeps humidity away from your spools. What It Is This is an…
Modified Fizzy's Panel Clips to work with BoxTurtle lower deck plate. These are the FT (S1)'s
Mounting Brakets to Put a BoxTurtle on Rails as the Topmount. The Feet can simply Stand in the Mounts. Its easy to remove for Maintenance at the BoxTurtle or the Printer. Used Hardware: 4x M3x10 SHCS 4x T-Nut M3 Printed in ABS with Voron…
This is a specific model designed fot the Formbot led kit for the BoxTurtle
free spinig wheels with oneway clutch magnets in ring and frame needs to bee repelled extras 4x using 75mm long hex7 m5 standoff, need to cut 8x 6705 bearings 80x 3x3 magnets 8x m5x10 ultra thin flat wafer head 8x F695 bearings 8x 5mm…
These are Splitted Trays from The BoxTurtle You will need: 3x M3-Nuts 3x M3x8 Countersunk Screw Discord: Box Turtle Github: Box Turtle Have Fun to build it ;-) And Join the Discord Community of the BoxTurtle. Also an Big Thx to the…
The Original TurtleNeck does not have to be modified. The 4 M3x8 SHCS used for the TurtleNeck have to be ferromagnetic. The .step files with “jst” in the name are for the mod with the jst-connector. Required Hardware: 4x 6x3mm Magnets 1x…
Wheel Guard helps keep thinner filament rolls from getting out of track
Here Are you seeing , an Gantry Servo Depressor for the Filametrix or the FilamAtrix. This Servo Depressor works with the normal Filametrix or FilamAtrix (CW2 and G2E) Material are needed: 1 x M3 Heatnut 1 x M3 4x3x5 Heatinsert (short…
Boxturtle enclosure user mode. Four 380 mm profiles, two 360 mm profiles, and two 220 mm profiles have been added to the Boxturtle base model. PTC heater can be controlled by STC-1000. The front panel is modeled after Ratrig's enclosure.…
Enable support and print - the box is hidden under the lane so quality doesnt matter.
Wanted to avoid connecting 2 hubs so I made a 8 way hub. Print with Voron recommend print settings at 0.12 mm height (thus 0.08 mm height will give even better results).
In order to use my USB cable on the LDO Boxturtle I needed more room underneath the AFC, so I made a simple spacer for a longer M5 bolt that can be scaled up & down in (Z) the slicer.
The design is similar to that of FbeauKmi's Filamentalist F1 but adapted for the BoxTurtle. Print parts (for 1 respooler) ABS 2x Wheel.stl 2x Hub.stl Settings : 20-40% Infill TPU 95A 2x Tire.stl Settings : please activate Spiral Vase mode…
I found that the TurtleNeck mount bracket on ArmorTurtle/TurtleNeck Github was too loose to hold the TN upside down when mounting it to the Box Turtle itself (like Steve Builds did on his build). Borrowed the idea from @ViktorvonDue's…
Remix modu rear_skirt_option_plates z Discordu od Robert Klotz - mono ve jednom kuse
V páčce je magnet na druhé straně, a je vymezen pohyb proti originálu. Lehce upraveny díly pro vymezení pohybu, modely jsou bez podpor, nezapomeňte si je přidat!
This is a remix of the original BoxTurtle part. It allows you to use a CLINKO M12 connector for the cable that runs between the BoxTurtle and the printer's main board. It's up to the builder to work out the details, but my planned…
Formbot corners with hole for connector, dont forget add supports!
Not sure how I wanted the skirts for my 🥰 BoxTurtle , whether to go the true mesh way or rather opt for a mesh-like look only but have them printed solid 🤔, I played around in CAD to have the mesh as a separate part and also to do some…
The 🥰 BoxTurtle Enclosure comes with a redesigned front and different skirt parts which require some changes to the TurtleFence . So here they are: Modified front skirts, spacers and the clip-in mesh inserts to fit the enclosure … and of…
The 🥰 BoxTurtle's 4-in-1 hub can be a bit “ temperamental” 😖 when loading filament in certain situations (especially on lane 4 ) with the filament getting caught and stuck in the bearing recess at the end of the filament path. There is…
The lovely 🥰 TurtleNeck filament buffer is somehow missing internal cable management and any protection 🫢 for the Omrons' pins. But no worries, that's now solved 😉. And while extending the frame and lid for improved cable management and…
Add your serial to your BoxTurtle Download the STEP file for Fusion Just add "Text" in the plate for your serial Use a double side tape to hold the plate The pin hole in the skirt is to insert a allen key to remove the plate Feel free to…
This is just a tiny little model for the Option Plate Mod of the 🥰 BoxTurtle's rear skirt. It accommodates a CNLINKO LP-12 💪 connector, e.g. to connect both CAN and 24V. Additionally, the design incorporates a dedicated cable outlet for…
Warning: Work In Progress! This project is still fairly early and may experience significant changes. Feedback welcome. Printing 3 shells, top & bottom layers @ 15% infill should be fine PLA, ABS+, PETG, etc should all be fine. ABS will…
A simple mod that will allow you to use regular m3 nuts instead of heatset inserts. I had problems with the original design, I couldn't tighten the screws on the shaft enough, my heat inserts were spinning into the plastic. My mod uses…
You have the snappy TurtleNeck PLUS so you can easily take it on and off your printer or beloved 🥰 BoxTurtle ? And of course you are looking for a nice and clean solution to manage the cable and keep the PTFE tube where 👉 you want it?…
One of the nicest add-ons for your 🥰 BoxTurtle are the 🤩 Box Turtle Lane Control buttons by Discord user Trev1Ak but sadly they do not fit the skirt of the BoxTurtle Enclosure with its slightly different shape. So I made it work … and…
This is just a remix of the Wheel Drives, but with heatserts for some of us that are a bit more heavy handed.
A modified Set of Boxturtles Desiccant Case and Lid. Based on and for: https://github.com/ArmoredTurtle/BoxTurtle Why? I printed the Desiccant Cases and Lids in ASA as all other Boxturtle Parts. Afterwards i checked the Fit and…
I have a lot of problems with the original Boxturtle Respooler wheels. The original design worked fine if you used PLA, but it didn't account for thermal expansion/shrinkage of ABS. Even with my chamber temperature stable(60c +-1c), the…
An XT30(2+2) for compatibility with ERCF/SB2209 canbus cable, two microfits for EBB36 and AFC-Lite wiring order.
Guilder for BoxTurtle with built-in supports extended to touch the build plate Print with recommended BoxTurtle print settings. Original model and credit goes to the BoxTurtle team. BoxTurtle license also applies.
Advantages compared to the 2-part design: Easier handling: No need to slice, align, and assemble two pieces – now it’s a single print job. This saves time and reduces the chance of errors. Better stability: Printing in ABS (or similar…
Ball-type linear guides have been used to replace the original sliding friction, photoelectric sensors have been adopted instead of micro switches, and magnetic retention has been added to prevent premature movement of the…
Want to give your BoxTurtle Enclosure a sleeker look 😎? Or do you need a bit more clearance on top 📐? Then have a look at these low-profile feet 🤩! By replacing the original feet with 2mm rubber pads, you can lower your BoxTurtle for a…
The wheel can be printed with any material and the tire must be printed in TPU or other flexibel filament. I used TPU 95A. 0.2 layers and 20% infill is more than enough for the wheel. The tire is best printed with a random seam and "Avoid…
I use it for the Formbot RGB Led's with the original printed corners. https://github.com/ArmoredTurtle/BoxTurtle/blob/main/STLs/Base_Build/Printed_Corners/corner_printed_x4.stl If you pinout the connectors, it is no Problem to use the…
Tired of your BoxTurtle filaments sitting out in the open? I designed this simple adapter to give mine a proper home inside a Sterilite tote. It's a cheap, easy upgrade that keeps humidity away from your spools. What It Is This is an…
I use this model for mounting the TN to my printer 3030 frame. It is designed for the TN jst mod and uses a M5x10mm BHCS screw and a hammer T-nut. Printed with PETG and 0.2 mm layers and 20% giroid infill.
Modified Fizzy's Panel Clips to work with BoxTurtle lower deck plate. These are the FT (S1)'s
Apex Extruder: The Next Evolution in Filament Management The Apex Extruder has arrived. Engineered specifically for the Box Turtle 1.1 filament changing system, Apex represents a leap forward in reliability and precision. By integrating…
Using the original, I ran into a few issues - The heatsets are in pull-out orientation, which isn't ideal, especially if using an auto driver. The final magnet flush-ness was extremely sensitive to the heatset placement - if the heatset…
Mounting Brakets to Put a BoxTurtle on Rails as the Topmount. The Feet can simply Stand in the Mounts. Its easy to remove for Maintenance at the BoxTurtle or the Printer. Used Hardware: 4x M3x10 SHCS 4x T-Nut M3 Printed in ABS with Voron…
This is a specific model designed fot the Formbot led kit for the BoxTurtle
BOM 470ohm Resistors 1,200ohm Resistors 1,800ohm Resistors 2,400ohm Resistors 3,000ohm Resistors 3,600ohm Resistors 4,200ohm Resistors 6,200ohm Resistors 7,500ohm Resistors 9,100ohm Resistors 6×6×5mm Switch button for each buttons.…
After upgrading my boxturtle extruders to the new APEX gearsets, i had to find something to do with the old extruders. It looked like they might just fit in the nightowl. Well it turns out they do as long as you change the thumb screws to…
