Counting matching models…
A desiccant canister designed to be mounted in the center of a spool of filament during storage to help keep the filament dry. The canister has a lock-ring which threads onto the opposite end from the cap, after the canister has been…
This pouring spout is designed for canisters with DIN threads , commonly found on 10 L and 20 L canisters . An integrated air channel allows air to flow back into the canister while pouring, resulting in a smooth, controlled stream and…
Preface This head was designed specifically for smaller printers, with a minimum build area of 18cm x 18cm x 18cm and to use comparatively little filament (a little over 200g), while still holding up against accidental abuse. If you don't…
This is a remix of the cylinder made by anewsome on Thingiverse . I needed a $4 dollars canister, so I remade it in fusion360. I also made a model for $4, $5, $6, $8 and $10. The dollars amount is printed on the bottom. All models uses…
I solved a very niche problem for myself, maybe someone else might profit from it. I needed an inlet basket for my reef tank. I had to design something that would skim the sandbed but not suction the sand into the filter. I printed it in…
This is a canister spout with an integrated air channel that makes pouring liquids much easier and prevents annoying glugging and spilling. It is designed for common 5 liter canisters you can find in European retail markets for distilled…
The original Scan (Atos Core 3D Scan) made by the Mammal Research Institute, Polish Academy of Science during the Open Forest Data project . You can download the original data here . I adapted the scan for 3D printing. The mandible is…
Double Stack Mag Pouch for left hand loading. This is designed to work with ELS and now also Tek-Lok mounting systems. If you have a gun that I don't have a pouch for just measure the magazine with your calipers (LxW in 3 different spots)…
🎯 Recommended Print Settings For Best Results Print this design with a standard 0.4mm nozzle at 0.24mm layer height for that sweet spot between speed and detail. We're keeping it lightweight with just 8-15% infill, which gives plenty of…
STABLE AND SECURE: Improves adhesion and stability on any surface, prevents canister from wobbling or tipping over. The stand fits for 90mm and 110 mm gas canisters, so you can use it with any camping stove. There are two versions to…
Scania R730 model RC wymaga klejenia i zaopatrzenia się w śruby m3 różnych długości. W razie problemów z włożeniem tapicerki do kabiny można z niej zrezygnować. Łożyska 6700 ZZ
The 285mm long Scania tractor model features steering and freely rotating front wheels. The model was printed entirely in PLA, with a quality of 0.10 and 0.15, depending on the size of the part. To add a touch of realism, we printed the…
Original part : https://www.thingiverse.com/thing:3985253/files
Guitar string winder tool. fit with bearing 608 without any tools. Manivelle pour mécanique de guitare se monte avec un roulement 608 sans aucun outil.
Interior diameter is 3.0 inches / 76.2 mm. Interior height is 2.0 inches / 50.80 mm. No supports are required. The model responds very well to scaling in your slicer if you want different sizes. The table below provides scaling factors…
Canine heads for dummy 13 Chest Armor - https://www.printables.com/model/1062776-dummy-13-lstr-engineer-armor Legs - https://www.printables.com/model/1085859-dummy-13-digitigrade-leg-kitbash Tail - https://makerworld.com/en/models/1088296…
Monsters Inc Scream Canister with text. Top, middle, bottom - 0.3 Black ring, spigot - 0.2 Text, accents and gauge items- 0.16 Remixed model to include a magnetic removeable lid, gauge surround and text, make sure you download the correct…
print can and cap and glue it altogether. You can print in diferent colours for better effect.
This is a head-base that can be used to build a puppet-, plushie-, robot- or a fursuit-head (costume). I did add some ventilation holes, that can also be used to attach fur. The lower jaw is movable. The model is scaled for costume size…
As I broke my Firemaple's stand, was looking for similar printable model, with no luck. It is designed close to original part. It should fold to fit inside the pot. Here some specs from their website: With the Canister Stand, it's easy to…
Update Feb25: Thanks for almost 300 downloads! Full Step Files available for Purchase from my Printables Store Here - perfect for alteration and customization. Free STL Files for 3D Printing below: Set of Modular Lens Cases, Protection…
Here we have a spacer that will utilize one of the OEM base plates from a 12rd magazine, and fill in the gaps around the 15 rounder to make it comfier for your hand. I personally printed with fuzzy skin, but you do not need to. Nothing is…
This is a canister spout with an integrated air channel that makes pouring liquids much easier and prevents annoying glugging and spilling. It is designed for common 5 liter canisters you can find in European retail markets for distilled…
Hello, Here is my remix of DIN61 cap. I added 3/4" thread for tap
This is a 35mm Film Canister Replacement. ******************************************************************************** ATTENTION There is an STL File of the Canister that Works Better with TPU it is labeled: ( Film Canister FOR TPU…
Didn't fine any eligent solutions to this problem that retained the ball check valve used for priming the filter. So I made one. 1.5mm holes Print with ABS or PETG. I tested both. Settled on ABS as it looked nicer. Pictured is the PETG…
A pretty run-of-the-mill desiccant container. Remixed based on Tenshe's design because the 2mm silica gel beads were too small and fell through the top and bottom holes. I also didn't need the space for the hygrometer, so I was able to…
The Volcanic Pistol Having recently printed the excellent Cattleman Revolver model from agepbiz , I thought to myself: You'll be shocked to hear that I too, have been enjoying Red Dead Redemption 2. So I sat down, spun up Autodesk 360 and…
Here's my contribution to all the quarantine creativity: an approximately life-sized C-20A Rifle used by the Starcraft character Nova. Originally I ripped it from an in-game asset, and then added detail from there based off of numerous…
I'm too lazy to buy this things. Canister cap with 1/2" inside thread for my campervan. Designed for print without supports. I print with Prusament PET-G Orange.
🌋 Volcanic Tealight Holder – A Warm Eruption for Your Desk! A miniature natural wonder that instantly transforms the atmosphere of your home or office! When paired with a standard LED tealight, this Volcanic Tealight Holder creates a…
I wanted an on-theme way to store/display my kyber crystals, so I made this! I might eventually make a v2 to accommodate an LED strip to provide some illumination behind the jewels, but that's a job for another day. Parts are split up to…
Simple opening and closing spanner for standard 4- or 8-ribbed lids of canisters between 1L-60L volume (DIN 45 thread, Ø48.2mm | DIN 51 thread, Ø58mm | DIN 61 thread, Ø65mm). Turn tool around or use the included insert depending on the…
Trichter für 5 Liter Kanister zum aufschrauben. Gewinde M39,5 x 4. Es gibt mehrere dieser Trichter, aber bei keinem paßte das Gewinde für meinen Kanister. Empfehle das Gewinde mit der niedrigst möglichen Layerhöhe zu drucken; empfehle…
Mushrooms have inspired incredibly beautiful lamps and other decorative designs, but to my surprise not a single jar or canister. That while I imagened it would be so nice... Let's change that. Here's my impression of what it should look…
Feet for gas canisters used with backpacking stoves. Use three to make the gas canister more stable. They can be stacked
1/10 scale off-road fuel/gas canister. Two mounting options - straight through (you'll need an M2x18mm or so - total height is about 12mm) or using the circular disc and mounting to your truck/surface first; then mount the fuel canister.…
Hello, this is a remix from the canister spout to fit canister with a DIN45 thread. They fit on my canister with 2,5 L and 5 L. The cap ring I got from https://www.thingiverse.com/thing:2484159 , it fits very well. Category: Household
This is a stand to add additional stability 3 different types of gas canisters commonly used in backpacking/camping stoves (65mm, 90mm, and 110mm). The goal was to make a gas stand that fits several different sizes of canisters, without…
Esta rueda loca ha sido diseñada para ser compatible con canicas de 15 a 16 mm de diámetro. Es un componente esencial para tus proyectos de robótica y movimiento, permitiéndote crear mecanismos de ruedas locas con facilidad. Detalles del…
20litre plastic cansiter for 1/14 scale. For best result, print them as shown in the picture
Cozy Canine Sculpture 3D model ready to print.
A set of Mini Cansters! Previously I made a set of Sci-Fi inspired canisters . They were big, they were cool, but the smaller of the models weren't as practical because of some of the proportions. The aim here was to shrink the model…
This is a functional and screen-accurate Cryo Canister from the first Jurassic Park movie. Most of the credit goes to BadWolfProps which made the original files and coffeehedake which remixed the middle cylinders to be the right size from…
I copied this here for archiving and to provide others with an easier print. I've adjusted the orientation and provided one that is reduced in size to accommodate 100g canisters. I printed mine in PETG using supports and 4 perimeters for…
New petrol canister lid with Buttres M40x4 thread and with groove for rubber seal. Update 19.01.2024: After 3 years I discovered (and also read) that PETG does not tolerate bio-component (and some additives) in gasoline very well and the…
Two different holders or mounts, for my Canik TP9SA. One is designed to sit on a shelf and hold the pistol at the ready to grab it. The other is a wall mount to hold it vertically. I have a small safe and wanted to utilize as much of it…
Replacement floor plate to enable easier seating while loading a magazine into your Canik. The extra thickness allow you to slap the mag in place without the magwell getting in the way. I've tested this one on my METE SFT with the magwell…
Llavero original de la silueta del camión Scania, imprimelo como máximo a 0.16 y despacito para obtener buenos resultados
I have shrimp in most of my tanks and have to filter the intake of my Fluval 107 and 207 canister filters to prevent shimp and fry getting sucked in the filter. I designed this because I was tired of dealing with a sponge other the stock…
Similar sizing to existing backstraps with the addition of an xs and xl. Fills in the gap behind the 10 round mag. If you like the design help me fund more pews. https://paypal.me/Bernsy97?country.x=US&locale.x=en_US
Hello all, this is a remix of two existing designs. I have connected the DIN 51 canister cap with a Gardena connector to easily fill canisters with a hose. The Gardena connection requires a standard O-ring.
With this stl file you can print gas canisters for WPL RC Trucks in 1:16 scale or diecast models. The stl file can be rescaled for other scales. The gas canister can be printed without support materials! If there are any questions, please…
This a remix of Ludwig Bre's DIN51 canister spout https://www.thingiverse.com/thing:4314888 which I modified rather heavily. A friend needed a cap for her fuel canister with two 10mm holes for tubes, I kept the third small hole for…
Una tecla simple para teclados mecánicos. Debería andar sin problemas en cualquier tipo de switch ya sean blue, red, brown, etc. Es una copia exacta de las teclas de un teclado 75% T-TGK315. Cabe mencionar que al ser un modelo chico en…
support needed. activate ironing (example pictures were printed without ironing 😞). support benötigt. bügeln aktivieren ( Beispiel Bilder wurden ohne bügeln gedruckt 😞).
Tezmahucani- Guardian of the Sacred Geometry
A replica of the movie prop that fits in a stash canister
Print Settings: Printer: Prusa MK2S+ Filament: PETG or PLA Tested with PETG Layer Hight: 0.3 Infill: 5%-10% Rectilinear Exterior Perimeters: 2 Brim: No Heated Bed: Recommended Supports: No Approximated Filament Usage: 11.79m Approximated…
Canister Holder for the Multiboard MultiConnect system, requires 2 https://www.printables.com/model/716558 connectors Different sizes available
This is a dry fire stand for a Canik Rival. It has cubby holes for a Mantis and a Streamlight TLR-1 HL (or smaller). It is cut for 3 magazines (IDPA). I made this so I can remove this tray from my gun safe and load up competition belt rig…
Esta rueda loca ha sido diseñada para ser compatible con canicas de 21 a 22 mm de diámetro. Es un componente esencial para tus proyectos de robótica y movimiento, permitiéndote crear mecanismos de ruedas locas con facilidad. Detalles del…
I shoot and home-develop a lot of different film formats. APS has a unique canister, which is fiddly at best, and a PITA at worst. These tools are designed to take the pain out of handling those reels. There are two tools and a…
Print Settings Printer Brand: Prusa Printer: Prusa Mini+ Rafts: No Supports: No Resolution: 0.2 to base & 0.15 to cover Infill: 15% to base & 0% to cover Notes: Esun Pla+
Dobrý den, Mám pro vás canister pro RC auto, jeep, expedici. Canister ma sroubovaci vičko pro lepsi autenticitu. Canister je ze dvou kusu!!! Tistene bez podpory!!! Pokud vás moje práce zaujala, odkazy jsou zde:…
Scania 113h topline modelado al detalle
Easy to print tube with secure screw on cap. Print with black PETG.
Softair bottles arrives usually in carton boxes, once a few have gone the remaining ones wander around and they are under pressure! this canister keeps them in place, full capacity is 13 but, because I carry also maintenance oil bottles,…
-printer Creality ender 7 -slicer Prusa slicer Print settings -infill 25% -layer height 0.2 -no support -material PETG Printing time 4hours Material used 50g the size I printed X=181mm Y=236mm Z=7mm
The " Spout Canister DIN45 " fits the hole in the remixed " DIN45 Canister Cap ". I've found the other cap to be better than the original spout cap, so now you have a choice of two.
Sturdy foldable gas canister stand for camping and backpacking. Compact and lightweight. Print in place design. For 90mm and 110mm diameter gas canisters. Version 2: larger stand diameter, better locking, more secure canister fit, higher…
Lots of people have designed containers for desiccant (silica gel). Lots of people have designed such containers to fit in the centre hole of a filament spool. This one is mine. Features Sized to fit in the 50mm centre hole of standard…
About the Film Canister Holder: This is a simple remix of the base Gridfinity template adjusted to fit very precisely most common film photography canisters. Sizes: The hole is 32mm to best fits film canisters of 31mm of diameter (most of…
Gas pedal for Canik Rival, to control muzzle rise. Mounts to picatinny with 6-24 x 1-1/4 screws. Also a picatinny to mount below it, I used to mount MantisX sensor. You'll have to play with orientation and support to get the best results.…
c est un cœur avec engrenage facile a imprimer que je partage gratuitement au prix de 1.31 sur cults 3d merci si vous le télécharger
IF YOU LIKE THIS MODEL, CHECK OUT MY OTHER MODELS AND SUPPORT MY PAGE Patreon at https://www.patreon.com/pixelchronicles ! Pokemon inspired, Arcanine, Tabletop DnD miniature 50 mm Large base which can be used for DnD and other Tabletops.
I originally designed this canister to hold my Flexcut carving set. But I quite like this model actually and want to use it for a bunch of other things. It's kinda shaped like a chunky peanut butter jar… and will look like one too if you…
High Power Rocketry e.Charge case This is a simple and quick to print recovery charge case in four sizes. This uses standard electronic matches that when seated in the case, prevent black powder leakage. They're designed for single use…
Notes pour l'impression Testé en impression PLA et résine. Nécessite un support pour la fixation en croix qui est légèrement en hauteur par rapport au bord de la touche. Notes de montage Quelque soit la matière utilisée, nécessitera de…
I printed the metal parts in Gun Metal Grey and the ooze was printed in a bright “toxic” green. you will want to use supports to support the middle part of the R, which will have to be glued into place independently.
Diese Freilaufbühne ermöglicht es, Modellfahrzeuge im Stand einem “Probelauf” zu unterziegen und Einstellarbeiten am Antrieb (Antriebswellen, Schaltung, Getriebeansteuerung) durchzuführen. Die führenden Zahnstangen verfügen über ein 2 mm…
This is my take on a key for my bearvault cannister. This model has an easy attachment point to the canister for simpler removal (especially in the cold), a vertical wall for stability that is contoured to the curvature of the cannister,…
Works well. Print in black to hide the oils/carbon. The actual pictures are from an older design, the logo was changed to make it print better. The step file does not have the “Canik” filler, only the recessed areas. The 3mf file will…
This is a cool model that I found on Sketchfab by RISD Nature Lab. This model is actually quite easy to print. There are just a few adjustments you need to make before printing. Add a raft at 2 or 3 layers for the best bed adhesion (or…
Double mag pouch for Canik TP9 SFX pistols designed to use Safariland ELS mount. I believe this will fit all TP9 Magazines There is O-Rings between the plastic to hold tension on the retention screws. Hardware needed (2) M5x20 screws (2)…
I started trying to use the “Walther PDP Compact Magwell-Compatible Baseplates” , but was unhappy with the retention. It felt like the base plate could come off accidentally. I haven't retained any dimensions or design features from that…
Excellent base for furry canis like wolves, foxes and dogs
Save some space and stack up those fuel canisters. Made for 90mm/3.5" diameter gas canisters with plastic caps.
Canister holder with spacer for second canister For assembly you will need: Nut M6 4 pcs Washer Grover M6 4 pcs Screw M6x30 DIN 912 (ISO 4762) 2 pcs Screw M6x50 DIN 912 (ISO 4762) 2 pcs Nut M10 ISO 4032 4 pcs Washer Grover M10 2 pcs Screw…
Print four parts like pic below.
This is a small container I've created as a clean wrapper for a little present. A wrapper with a little twist. Because of the clean design it might be a good starting point for your own decorations or modifications. Have fun to print and…
conector de canillas para mangueras de 1/2 pulgada
Intorior door handle for Hyundai Coupe/Tiburon/Tuscani GK 2001-2008 Copying the design and printing it was cheaper than buying a new one from dealer, so maybe someone else will have a use for it. For UK and other left hand driving…
Smal canister, malí kanystr o obsahu 10L. Velikost 47x35x10mm. Oválné díry jsou uzpůsobeny na šroub M3. Jedná se o velikost 1/10 reálného “expedičního” kanystru.
