Counting matching models…
By accident created a nice little crankshaft mechanism. With very little cleanup, mostly the brim, and a careful rotation of the parts, it works. It is one print, no support material or anything else.
This model is compatible with the lego system.
This model is compatible with the lego system.
Printed with PETG, nozzle temp: 240, bed temp: 90, recommend printing with supports so that the axle holes are vertical.
With this custom 120° crankshaft you can build a straight 3 cylinder or a V6 engine with an even firing order. for a complete crankshaft you need 3 custom 120° crankshaft pieces and 3 regular crankshaft pieces which you can download…
This crankshaft locking tool allows loosening and torquing of the crankshaft pulley bolt at the front of the engine. This bolt needs to be removed to perform the belt service. This tool should be printed with thick walls and at least 80%…
sparepart spacer if you lost your Shimano crank spacers. nothing special
360 degree wheel. Bolts onto either the harmonic balancer in car of a 4G63 or the crank sprocket using the harmonic balancer bolts. To install, attatch the hub to the car, then slide up the wheel and align it to the hub. Using 2 interior…
This bicycle chain/crankset cover guard works on any bike whose screws are squarely located 100mm apart from one another. I use it on a Specialized Rockhopper 29.
The crankshaft is a key element of the crank mechanism in an internal combustion engine, which converts the reciprocating motion of the pistons into rotational motion. It is a long shaft with many cranks (cranks) to which connecting rods…
I designed this crank ring protector for my Torpado MTB Chiron 27,5'' as the original part broke. The distance between the screw holes is 88mm, so check your bike for compatibility. So many bikes have the chainring guard protector missing…
Use this crankshaft spacer after removing the crankshaft pulley to turn the engine with a ratchet. Unlike the spacer described in the workshop manual, this one slips onto the crankshaft and locks into the key. The outside of the spacer is…
These bumpers are fitting the currend and older SRAM cranks. They are styled not like the original SRAM bumpers, I used the design of my e.13 crank bumpers because these are a bit thicker. My current version is printed in TPU, you may try…
Choose between single-piece or multiple-piece design. I recommend the multiple-piece design because you can print it laying on bed and thus get more precise dimensions of the bearing faces. You will need 8pcs of 3X10X4mm bearings (4pcs…
Crankshaft clamp needed to lock the shaft of RC nitro engines when tightening up the clutch nut. This one fits O.S. engines: GT15, 105HZ, 91HZ / SZ / RZ (including R versions, i.e. HZ-R). Replacement for genuine O.S. crankshaft clamp part…
Print the top near where the skate bearings mount with a modifier and 100% infill. The first balancing stand is actually untested, the 2nd balancing stand is tested, but if you push it the wrong way, without a lot of infill, it affects…
Tool used to turn over the engine when doing timing on older BMW engines, or newer engines that are missing the integrated adapter. I might design a version that uses metal inserts or something to strengthen the holes, but worked for me.…
I created this for my bike with a SR-Suntour XCT V2 48/38/28 Crankset. The holes for attaching the chainguard are 110mm and 120mm apart. You will need 4 around 5-8 mm long M4 screws with countersunk or very flat heads. I already printed…
My new CUES crank didn't come with a chainguard, this design fits just right. Feel free to adapt to more Cranksets, or let me know the hole spacing of the other CUES cranks! Designed around the cheap heatset inserts, files provided for M4…
I gout a touring bike that i use for daily commute. It is comfy and quick but few times I got stain on my jeans. I removed the original plastic piece and designed this. Warning: If you remove the original plastic peice from the crankset,…
Use as an educational tool, display piece, or decoration.
peça para apertar parafuso e rolamento da pedaleira tipo bb51 Ainda não foi impressa a peça english version (google translate) piece to tighten screw and bearing bracket bb51 It has not yet been printed piece Category: Hand Tools
Just added a 10mm hex (slightly smaller so it fits better) to cmh's design so it sits easier in my cannondale cranks
Not much prose for this thing. It's an easily printed Preload Cap Tool for Shimano Hollowtech II Cranks. 8mm hex for your convenience.
A 4-cylinder crankshaft is a vital engine component that transforms the pistons’ linear motion into rotational motion, driving the vehicle’s power output. It contains four crankpins, each linked to a piston through connecting rods, and…
One to one piston and crankshaft with moving components.
Front Main Seal/Crankshaft Seal Driver for the first generation Honda CRV RD1. Printed in 3 parts so you don't need supports. Part 1 and 2 lock into each other and then part 3 is slid into part 2. You can use something to tap part 3 down…
A tool to drive in a front crankshaft seal (don't get Timken, they will go in cock-eyed) 55x40x7 seal, chamfered entry
Montage Seal Tool For Piaggio Moped Engines (flywheel side) The engine gasket sealant installation tool for Piaggio Ciao is a valuable tool designed to facilitate the installation of engine gaskets with consistent pressure distribution.…
Do you hate having to use a hammer and an expensive special tool to install a front crankshaft seal (Front main seal)? Simply put the new seal on the tool and use the harmonic balancer bolt to press the seal into place. Print with a high…
Crankshafts can warp while being stored horizontally, print one of these for each main journal & store them safely.
Drill a 3mm hole in the bottom if you are concerned about water being trapped when the crank is stored in the down position. Printed in PETG with variable layer height (0.2mm max, ~0.11mm near the top). No supports or brim needed. To…
Can effectively prevent dust, dirt and rain water into the hole to get rusty. Size: 27mm x 8mm Inner diameter: 20mm
decathlon not have parts for theyown stuffs so i print my own guard. Ref. : 968556 Square-shaft transmission, 7-9 speeds
Simple chain catcher that prevents bicycle chain from falling inwards towards the bottom bracket. This was designed for a Look 795 Blade with a Shimano Ultegra R8000 derailleur and crankset, so you may have to modify the model to fit the…
This is a 3D-printable version of the FEL-PRO 16300 crankshaft sleeve installation tool. Used to install the FEL-PRO 16250 crankshaft rear main seal sleeve on engines like the legendary pushrod 5.0L Ford V8 (among others). The center is…
Garde-chaîne pour pédalier Shimano GRX FC-RX820-1 (38T à 50T) (Testé uniquement avec le modèle 40T) 31.05.2026 : Ajout des modèles de garde-chaînes pour 38T, 40T, 42T, 44T, 46T, 48T et 50T (nouvelle version) Paramètres d'impression : PLA…
Cover for a crankshaft on a bike. I made this one specifically for an Olmo Champion Gran Prix. Check the dimensions in the image to make sure it will fit for you. Modify the .f3d to suit your needs.
These are protective sleeves that protect your precious carbon crank arms from curbs and rocks. There are two versions here, left and right. Why two different versions are needed is not clear to me, however, the measurements of both my…
Camshaft Key Assembly Crankshaft Pulley Tool I suggest ABS and 100% infill to make it strong.
The Y1MD14100 spacer that comes with the FC-M6120 is a tad too large in diameter if you're pairing it with a higher-end, XT level BB-MT800/BB-MT801 bottom bracket. Instead of that, you need a Y1PW98070, the stuff that comes with the XT…
Crankshaft plug on the timing side YAMAHA XT 600. he most suitable printing material is Prusament PC Blend, I have tested it for 2 years of riding, I leave the mtrial link…
The original coupling broke (ivory in the photo). I made it from PLA+ (light blue in the photo) - it lasted for 20 minutes of work, melted and fell apart. Made from PETG (white in the photo). After an hour of work, I disassembled the…
Falls euch wie mir der Lagerring zum austreiben des Kurbelwellenlagers bei der KTM 690 fehlt. Der Aufsatz verhindert das die Walzen beim ausschlagen aus dem Lager fallen. Mit einem entsprechenden großflächigem Aufsatz kann es nun aus dem…
basically it is an alternative to EAN-GTIN 8590831431217 I needed to remove a GIANT Bicycle crankset / camshaft It uses the same nut as some freewheels with 4-notch pro tip: don't use pla it is to weak trust me i tried
This is a two hole version versus the older one hole version.
Renault K4M, K7M and derivatives engines do not have a stop for the front crankshaft oil seal (7700273776 is the size of the oil seal 35*47*6 ). This mandrel is made in size from sources on the Internet and personal measurements. Tested…
Update: V2 has lower schoulder with a larger base to fix a problem with the friction of the part. Prefer to print it in PETG or ABS. Attach the chain guard to the chainring with 5 M4 bolts if your chainring is not threaded. In the other…
It was printed on a I3 MK3 with Prusament PLA 0.3mm draft. Perimeters vertical and horizontal shells : 4. Infill : Honeycomb 15%. Auto generated support. To make this tool operational, you will need a M8 bolt long enough, a pile of washer…
Modified the crank shaft to allow a pin to hold the handle on.
Crank threads dust cover. Made to replace a lost cover on Miche Primato cranks but could probably work on other cranks.
APEK-AS 56 ME Pro Line, 6501 Pro Line, CHAMPION ST553, ST661. Part Number: KCM22B-02-17
I present the scale model of the crankshaft of a BMW R90S. In order to make the key ring more compact, have been removed the part of the shaft that go to the drivetrain and the oil pump. For its printing, I suggest a height of 0.15 mm,…
EN: Available as a single part or complete bracket DE: Verfügbar als Einzelteil oder komplette Halterung
It fits perfectly, however I don't recommend PLA as it isnt strong enough.
I found Bash Ring for Shimano FC-5100 Crankset (32t) by i32 ( https://www.thingiverse.com/thing:6905994 ). but it didn’t work with my 30T chainring. This is inspired by that, but I changed diameters, and thickness, removed material around…
I bought a Varstrom/Bafang ebike conversion kit from the 'zon and needed the right PAS sensor because my bike has external bottom bracket bearings. The kit came with almost no instructions. The instructions for the PAS magnet ring were…
B230 Crankshaft Pulley Holder Tool Just a template for custom metal processing, fitting well...
Just a quick crank jig, i made the Spacer and Reducer specifically to true a NSR125 crankshaft. i made the dimensions quite generous for bigger bikes in the future. it mounts to the bed of my mill, and i used a dial indicator holder to…
Designed this socket to use a 1/2" drive tool to spin a Honda K20 or K24 engine over with no crank pulley bolt. This model uses the factory crankshaft key to function, so one of those will be required. Printed with a .4mm nozzle, .24mm…
Print Recommendations: (what worked for me) Material: PETG-8% CF Wall Loops: 3 Infill: 15% Gyroid Layer Height: 0.16mm Additional Parts: 6x 2mm Steel pins Length recommend: 12mm (see note) Note: I used 12mm long pins. I have provided…
It serves a dual purpose: it acts as a dust and dirt plug to keep the hollow spindle clean, while discreetly housing an Apple AirTag or Novoo tracker inside for hidden bicycle tracking. The two-piece design secures safely inside the…
Scanned BY VOXMETA H1 PRO 3D SCANNER - A Powerful Tool for 3D Printing, Reverse Engineering and inspection Real part → 3D data → Ready for digital design Learn more details about VoxMeta 3D Scanner Download more 3d models
Typically when replacing the timing chain or setting the timing on the BMW-PSA Prince engines, the flywheel or flexplate are used to set the crankshaft position by inserting a tool through the block. When the engine is on an engine stand…
Best printed from flexible filament, but solid materials will work too.
needed a sealing ring crankshaft r1150 gs help for mounting the inner sealingring of the crankshaft of a r1150gs motorcycle i resin printed it but i need to work on it on the outside ( old resin)
My crankset guard broke recently, so I went searching for a reasonable replacement model. I found https://www.printables.com/make/3670725?comment_id=3670725 which is a great model, but unfortunately wasn't a good match for my crankset.…
Replacement part for connecting the piston to the crank shaft cam on a Wagner 130 paint sprayer. My was broken and this replaced it. Printed in PC with 6 walls and 40% infill.
a single chainring with cranks and pedals
Update: V2 has lower schoulder with a larger base to fix a problem with the friction of the part. Prefer to print it in PETG or ABS. Attach the chain guard to the chainring with 5 M4 bolts if your chainring is not threaded. In the other…
The crankshaft is a key element of the crank mechanism in an internal combustion engine, which converts the reciprocating motion of the pistons into rotational motion. It is a long shaft with many cranks (cranks) to which connecting rods…
This is a 25 mm press-fit crank arm dust cap designed for ACID cranksets used on Cube Stereo Hybrid e-MTBs, compatible with: ACID Crank MTB Hybrid ACID Crank MTB Hybrid PRO The original caps are easy to lose, and once they’re gone the…
Just a quick crank jig, i made the Spacer and Reducer specifically to true a NSR125 crankshaft. i made the dimensions quite generous for bigger bikes in the future. it mounts to the bed of my mill, and i used a dial indicator holder to…
Award medal for Cranksgiving alleycat participants. https://www.cranksgiving.org/ Modify here: https://www.tinkercad.com/things/0pcOORdFKAO-cranksgiving-award-medal Here it's printed in Bronzefill at a staggering 2mm layer height.
Bike chain protection for crankset Prowheel Suolo 22/32/44Т.
I designed this to fit my 5 screw bike, to be printed in 5 parts, since the whole won't fit on a Mini print bed. I used stainless M4 countersunk socket head screws and matching M4 nuts. The Onshape CAD drawing is parametric, so should be…
Crankset keychain modelled off a 110BCD THM Clavicula crankset. 30% of life size. Paired with 25mm keyring in pictures.
When renovating a bike equipped with an FSA Gossamer crankset, I decided to protect the crankset from accidental impacts, such as hitting the curb while walking the bike. The guard needs to be printed with TPU using supports.
plug to close this hole in this crankset from mud/dust ect
