Counting matching models…
This is a snap-fit case for the Adafruit 1.8 Color TFT LCD Display with MicroSD Card Breakout, ST7735R. This case is designed to be snap-fit together, not requiring any screws. Please check to see if this fits your display before printing…
Nozzle 0.4 Layer Height 0.2mm (Recommended) No supports needed Scale it as you like :)
Downscaled to Z scale. Tractor details were reinforced so could be printed at this scale. Trailer was designed mainly from photos and actual fuel trucks specs.
A simple cover for the Adafruit Trinkey QT2040. For making a DIY USB Nova: usbnova.com But I also included a version of the case without the NOVA text printed on it, so you can use it for any project. You also need 4x M2.5 4mm screws to…
DAF Sun Visor, printed with ASA material, nozzle 0.6
This model is designed to be printed with a few filament swaps. The model should be printed with a layer height of 0.2mm. You start by printing in red up to layer 4, at 0.8mm. Then, you swap the filament to white and print up to layer 11,…
This model is designed to be printed with a few filament swaps. The model should be printed with a layer height of 0.2mm. You start by printing in red up to layer 4, at 0.8mm. Then, you swap the filament to white and print up to layer 11,…
Replacement for the front windshield defroster on the DAF YA66 Dutch military courier car.
Stencil to make apply the painted emblem on the engine cover of the DAF - YA66. Stencil is split in two to fit the mk3s+
Bushing that can be glued to the doorframe to replace ugly water hose modification.
adafruits voltage regulator/filter PCB enclosure with 4 pin Connector fitted Header, Vertical, 4 Way - Jst (japan Solderless Terminals) | CPC Connector Housing, 4 Way - Jst (japan Solderless Terminals) | CPC Crimp Terminal, XH, 28-22AWG -…
I designed a replacement protection cap to prevent scratching of the transparent PVC on the soft top of a '74 DAF YA66 Dutch military courier car. The protection cap is can be used for any other 20mm round tube with a 5mm hole drilled…
Overview For a video tour of this tower setup, please visit this reddit post . In this video I explain how this quick-release system works along with some of the other upgrades that I have made for my Prusa i3MK3S+ with MMU3! (: The main…
Aktualizace 15. 10. 2026: přidány soubory pro dvoubarevnou variantu (Prusa XL 2T) a tiskové soubory bgcode, doplněn seznam filamentů a nstavení tisku. Geometrie kostky se nezměnila. Hrací kostka na osobní zájmena v němčině: ich, du,…
This is a remix as mentioned in the summary. I made this for a friends birthday and modified it to fit a standard 32x8 LED Matrix from Amazon. The modified files are the ear cups (threaded and hollowed to house electronics) and the front…
A diorama created as a collab by the designers Wekster , Dsk001 and The3Dprinting . Thanks guys! You can either print them in multiple pieces (no MMU needed) to have a multi-color model or you can use the single color version to print…
🌼 Spring Bouquet of Easter Daffodils Treat yourself or your loved ones to a 3D-printed bouquet of daffodils! This step-by-step guide walks you through printing, shaping, and assembling – for real springtime moments. Show off your skills…
I didn't find a mount for an Adafruit ADXL for the stealthburner which has wider holes so I created this one. You will need 2 M3x60 screws for the mount and 2 M2x8 for the ADXL itself and 2 M2 nuts. I hope it's useful for someone else ;)
Daft Punk Thomas Silver Helmet! Update Oct 2024: Recreated this version 2.0 from scratch. There were a few features that were bugging me with V1, so I created a new and improved model including mounts for LEDs All parts rotated to print…
Wearable helmet of the golden Daft Punk Guy.
a beautiful Deffodil with a stem that is suitable for decoration or as a gift. print the parts separately. !assembly requires glue, ideally instant glue or other plastic glue! It looks beautiful as a bouquet in combination with my other…
Case for Small RP2040 Boards This is a case for the small RP2040 boards such as the Adafruit QT PY RP2040 or the Seeed XIAO RP2040. These small boards based on the Raspberry Pi RP2040 microcontroller. They have a USB interface and are…
Added text/symbols for Power / HDMI / ON as mine is at floor level so awkward to feel for small ports. Added slots for blower fan to vent out end of top case Chamfered SD card slot for larger fingers + thumbs Increased Extrude depth of…
Introducation There are other 3D models of this vintage DAF logo, but I wanted an accurate logo that I can change, for example with a personal text as a gift. Therefor I made the logo in OpenSCAD. OpenSCAD is free software:…
Update: Added 3 versions - One with a hole for the STEMMA port, One with a hole for the STEMMA and Reset, and a last one that has space for a Pimoroni trackball. This is a form fitting case I designed for the Adafruit Macropad. Its…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Daffy Duck Tip: The tab on the bottom is designed for using something such as Sticky Tack (a reusable soft adhesive putty), to keep your artwork secure in even the strongest gale force winds :D I've also made the positioning of the tab so…
Compatible with Lego Wreath builds: https://www.printables.com/model/218071-lego-wreath https://www.thingiverse.com/thing:6418361 Note: I'm not seeing the Spring/Easter version here on printables anymore, so I've added the thingiverse…
DAFFODIL Decor Carefully remove the supports using clippers. One by one, in order. Start from the very top and with the thinnest ones. Take your time. Do not pull them off forcefully to avoid damaging the model. Printed with fuzzy skin…
This is a case for the raspberry pi 4 with an adafruit 3.5 tft screen. In the bottom of the case, you can use a noctuna fan NF-A4x10 5V. I used a 5V fan, so I can use the voltage of the USB port. The bottom and top is clicking, no screws…
A case for the Adafruit ESP32-S2 Reverse TFT Feather. Uses four to six m2x10 screws. https://www.adafruit.com/product/5345 Also included a battery case. https://www.adafruit.com/product/3898 I've updated both back plates to have better…
A bracket to allow the Adafruit ADXL345 to mount to the mini-afterburner in order to do pressure a advance. This designs uses m2 nuts and bolts to secure the Adafruit ADXL345 board to the bracket. and you'll need m3x40 bolts in to mount…
🌼 Daffodil – The Birth Flower of March The daffodil , also known as narcissus , is the official birth flower for March . It’s a bright, cheerful flower that signals the arrival of spring , often blooming as one of the very first flowers…
You know, I'm something of a cephalopod myself! Remix of the classic articulated Octopus. Print in place, articulated and can be printed without supports. No assembly or supports required . Printed at 0.16 layer height, 12% infill.
Daffy Duck Tip: The tab on the bottom is designed for using something such as Sticky Tack (a reusable soft adhesive putty), to keep your artwork secure in even the strongest gale force winds :D I've also made the positioning of the tab so…
Daffy Duck Cartoon character from classic Looney Tunes in 2 different design poses. Single extruder 3 color design. First bottom layer: White Second layer: Orange Third top layer: Black
64x64 LED Matrix Grid If you're printing yourself don't use this model!: This is is a really really slow path to printing these since slicers aren't optimized for grids like this. A better option is: Create a 192x192x6mm solid box (or…
This is a Daffodil that is compatible with my springy flower collection found here: https://www.printables.com/model/1100526-springy-flower-collection-update The dirt snaps into the planter, the stem screws into the dirt and the leaves…
YouTube: https://www.youtube.com/watch?v=jy7a-z19UEQ NEW UPDATE April 8, 2016 – Added new parts for Adafruit 2.4" TFT Feather Wing This is our 3D printed case for the Adafruit Feather. It’s for anyone looking to put their project in a…
Lucky 13 Daft Punk Silver head If you like it --> press like it :-) Daft Punk head as a remix for the funny lucky 13 figure. The original model is shared from the founder of Prusa Josef Průša . You can find the diorama which is created as…
This is a small case for all 0.7 x 1 inch adafruit boards. The case is very delicate, please print with high details. The lid is not designed to be constantly be taken apart, the clips will wear off very fast. The board fits snug inside…
3D printable enclosure for the Adafruit Macropad PCB, inspired by the Nuphy Halo 96 keyboard. Needed: 4x M3x8 screws Adafruit Macropad Print: Print all 3 parts facing down (as shown on pic), only the PCB bracket need support Assembly:…
Hello, Welcome to my profile, full of models and miniatures :-) I have Daffy Duck from Looney Tunes for you for an exhibition or diorama. Very cool characters. It is suitable for coloring. My kids absolutely love it :-). Important: If the…
This is a remix of https://www.printables.com/model/1447972-daft-punk-helmet-thomas-20-wearable see original thing for instructions and additional parts Compatible with parts from…
Lucky 13 Daft Punk Gold head If you like it --> press like it :-) Daft Punk head as a remix for the funny lucky 13 figure. The original model is shared from the founder of Prusa Josef Průša . You can find the diorama which is created as a…
I've printed a custom fan duct for my Ender 3 V2 and I didn't want to re-print everything just to mount the ADXL onto it. Instead I got highly inspired by this drag chain mount. I designed my own based on this simply because I liked the…
remix of the model coupling the two helmets to form the cover of this wonderful album. It may be necessary to apply a mirror effect to the model. It has been printed with MMU and I doubt that it can be done in parts, if someone does it,…
I can't find any decent enclosure for Adafruit 3.5 PiTft with Pi 3B. So, I decided to make one. To display MagicMirror stuff like weather, news feed, upcoming calendar events.. etc on my desk. You can find more information about…
full guide on: https://learn.adafruit.com/3d-printed-daft-punk-helmet-with-bluetooth Build a Daft Punk Thomas Helmet with bluetooth control! In this project we'll build the iconic Daft Punk Helmet with the ability to change animations and…
The next flower in the series, a daffodil! I recommend printing the part in PETG. I printed mine at 0.3 layer height with 0.45 line width. The parts are all printable without any supports. You will need to do some bending/forming of the…
A cabinet enclosure for 64x64 LED matrix (3mm pitch) with Adafruit controller. The enclosure is suitable for wall mounting. PLA-ST & organic support.
* Thanks for the original designers of both models.
You can scale the demensions and thicknes in the slicer up to 100mm without losses.
This print houses a single Adafruit QT PY board with USBC connector. The top snaps shut and has two button cutouts to allow you to press the reset / PIN9 button. It has a small slit in the back for cables - I use it to wire in external…
These cases are compatible with the following Feather boards: Adafruit Feather HUZZAH with ESP8266 WiFi: https://www.adafruit.com/product/2821 Adafruit HUZZAH32 – ESP32 Feather Board: https://www.adafruit.com/product/3405 Feather ESP8266…
Printed on a SunLu T3 fast print Disabled. 0.2 Layer Height 20% Infill No Supports Needed! Added a 1.2 version of the flower for less material usage.
This is a remix of the NVIDIA Jetson Orin Nano Developer's Kit Case. Modified it to work with the Adafruit Can PAL (CAN FD), and created a honeycombed bottom to provide airflow for the M.2 SSD and the rest of the Jetson's underside…
This is pretty much the same as the original, just easier to print and with a modified soldering iron clamp to fit the [Sremtch…
A sensor cover for the Adafruit Stemma Soil Sensor: https://www.adafruit.com/product/4026 Snaps Together nicely no glue needed. I print in PETg for outdoor durability. Logo on top (for those of you wondering) is for Team 4160 for which I…
Adafruit's Circuit Playground Chess Get ready to play with the Adafruit Chess set! It’s entirely 3D printed and features players from Circuit Playground. In this project we’re using metal filament to 3D print the chess peices. This…
Compatible with parts from Daft Punk Helmet Thomas 2.0 - Wearable for Small Printers
A solid prop of the Daft Punk Human After All era. Not sure of making it hollow but ask in interested
Share a Like please. Modelo criado para um camião Daf XF 2017 para servir de suporte para um tablet de 10''. Model created for a Daf XF 2017 truck to support a 10'' tablet.
Needed a way to attach my Sequre SQ-A110 to the Adafruit heat insert press, so I made these brackets for it. One is intended if you want to keep it on, and just screws in place. (use threaded inserts on the back piece of both versions)…
This case for the Adafruit MacroPad is a snap fit enclosure and requires no additional hardware. Layer height 0.2 Should be sliced with “Detect Thin Walls” so the tips of the snap tabs do not make gaps in the side walls. If you are using…
I made the missing pupils for the eyes on the Daffy Duck model. Enjoy!
When the Insterstella series of videos from Daft Punk came out i got instantly enloved with the music and the story behind them. I always wanted to have the small projection shown on the "Something about us" song and now that we can print…
I've created a small and simple case for the Adafruit BME688 sensor board for use with a Qwiic-Connector (no cut-out for the pins). I've printed it with Prusament PETG, not sure if other filaments will fit as PETG tends to shrink a bit.…
License plate stamped from Starboy, The Weeknd's song with Daft Punk. Placa de matrícula estampada de Starboy, la canción de The Weeknd con Daft Punk.
This enclosure was built to house a Sensirion SPS30 (particulate matter sensor) and an Adafruit BME280 (temperature, humidity and barometric pressure sensor) for an outdoor weather station. The goal was to have an enclosure that could be…
This is model is designed to be printed with a Bambu Lab AMS or similar. I recommend printing with a .2mm nozzle at .14mm layer height. The best sheet magnets I have found to use with this model is Marietta Magnetics brand 30mil (with…
This is a simple snap case for the Adafruit OLED Graphic Display (SSD1306) (.96") 128x64 character OLED display or any similar .96 display. The design is meant to be small/compact and snap closed. Only the standoffs are exposed. The case…
Wall mounts for the Adafruit RGB Matrix Portal Series. 4mm (tested) 5mm (tested) 6mm (untested) Print instructions Print with wall side down, 0.2mm layer height on Prusa MK3S with 0.4mm nozzle works well.
A fun little model i remixed and made for the 45 record adapter contest! make sure to like this post!
This is a simple casing for the "Adafruit FT232H IO" board. The SCAD files can be downloaded here https://github.com/andimoto/case\_adafruit\_ft232h Assembling the case with 2mm or 2.5mm screws. Print instructions Category: Electronics…
Created a snap fit case for adafruit HDMI touch screen monitor. I wanted a case without having to install hardware. Printed supports on the notches in the case. https://www.adafruit.com/product/2260
If you want to use your Adafruit feather in any sort of automation setting you might want to mount it on a DIN rail. The standard DIN rail mounts don't really have good mounting locations for the Adafruit feather board. This print…
This is a set of holders for Adafruit IR Beam Break Sensors. I am working on version 2.0 to address too small of a hole to fish the wires through on the bottom of the right side one. You might be able to see, but I temporarily took a set…
Daffodil Soap Mold. Designed to be printed with nijaflex for easy mold removal. Designed in gimp, inkscape, and tinkercad. in that order. Category: 3D Printing
(Will eventually upload a V2 that moves the iron up in the mount, that will reduce the leverage caused by the long soldering iron tip and reducle wobble.) You'll need two M3 (i used m3x5, of the type thats ~4mm in diameter) heat set…
Scale in almost any size you like and slice so that it starts in black then changes to white and then orenge then red. remix into a magnet or blow up to 30 inches high your choice. Display it somewhere prominently to make alien diplomats…
This is an enclosure for an Arduino project with an Adafruit Motor Shield V2 . I did print them roughly on a FDM printer, but the rods would render much better in resin. The pins made accessible on the top are 5V, GND, A0, for a pulse…
Ich habe ein DAF Schild erstellt für DAF Liebhaber. Es lassen sich die Logo Elemente rein Klipsen ohne Kleber, für leichte Ersetzbarkeit. Der Logo hat die Ideale Größe für das Druckbett von ein Ender 3S1. Drucken sehr leicht ohne…
This is a remix of Joaelso's original. Added a solid background and increased the height a little to make it more durable. I've printed it with a clear filament background to hang in the window. Also added a larger version with same…
I needed a way to hit a key combination on my computer while not at my computer, so the Adafruit NeoKey Trinkey was perfect for that application. However, I needed to be able to mount the key, preferably with the PCB not exposed. So I…
A simple 3d printed box used for housing an Adafruit Ultimate GPS breakout board v3 with usb https://www.adafruit.com/product/4279
I remixed the original case and thickened it enough to allow for the fan to be mounted inside. I also added a ribbon cable tab below the Pi's USB connections. With the added thickness, I was able to pull the ribbon cable out vertically…
Diese schlanke, unauffällige Wandhalterung wurde speziell für den Vodafone-Router entwickelt und ermöglicht Ihnen eine einfache und sichere Wandmontage Ihres Geräts Hergestellt für Stabilität und Diskretion, sorgt dieser Halter dafür,…
I initially printed the parts for this press while I was waiting for the hardware to show up. When it did, I discovered that the threaded inserts I had bought were a smaller OD than the parts were designed for, and they would drop right…
A beautiful minimalist painting of a Daffodil in a flowerpot on the wall or with a stand on the table. Size 175 x 200 mm You can find the small print stand for the table on my profile ↓…
Here is on request my lightsaber that I made with light and sound effects based on the original adafruit project. not being perfect, I leave with the Fusion 360 creation files which will allow the best of you to modify it, to improve it.…
I needed a sensor mount for my Enclosure Ambient Control project. I had a few requirements : It needed to sit close to the controller PCB so wiring is easy. It needed to have good air circulation It needed to be ridged enough for…
A quick 3D mock-up of Adafruit's Skinny Wheel for TT DC Gearbox Motors. Just in case you would like to print one for your purposes or make any changes to the hub that you may need. I printed the hub from ABS and the tire from TPU.…
A blank, matte-white model inspired by the intense and captivating presence of Willem Dafoe. This DIY collectible captures his unique energy in a bold, minimal form—perfect for fans of powerful performances and artistic personalization.
UPDATE Added flat version for 3D printing flat on the bed. A fidget spinner is a simple and basic handheld toy meant for mindless fidgeting. These toys are one of those "I don't get it" things, until you play with one. Fidgeting is…
![Daftpunk Helmet [Thomas Bangalter]](https://media.printables.com/media/prints/7156/images/50835_a09826a7-6b83-4f26-af9f-b181e4214238/hero_ex_6_7156.jpg)
