Counting matching models…
This is an overhaul and rework of EVA 3 to enable it to work on Mercury One.1 printers. E34M1 also comes with extensive documentation, including a guide to assembly. E34M1 Documentation Download your files through the documentation for…
I didn't want to buy limit switch PCBs, so I designed an upper mount with an inbuilt limit switch
The Blade should be cut to 32mm just get as close as you can while leaving the hole intact as shown in the picture https://www.amazon.com/TIHOOD-100PCS-Replacement-Hobby-Blades/dp/B07QP8L1QG Blade Holder: m3x3 Set Screw Blade Holder…
It's a newly designed hotend mount for the EVA 3.0 / E34M1 system. The version available here on printables allows the airflow from the hotend fan going to the nozzle. That can cause fine hairs on prints (stringing). I want to block that…
Obsolete: I have made this as slim variant by introducing compromises (mainly soldered cable directly to PCB). Since then I have redesigned this to more modular solution and I strongly suggest to use variants here E34M1 . They do support…
Remixed for my Ender 5S1 Mercury One.1 with a 235x235mm bed.
This is a remix of Psych0h3ad's work to adapt stock EVA intakes for E34M1. I punched a bunch of holes for a faster, lighter print.
This is a remix to use M3x5x4 inserts. No other changes are made. BOM Part Qty Notes Screw, M3 x 8mm SHCS 4 For mounting the EVA 3/E34M1 front. Screw, M2.5 x 8mm SHCS 4 Usually comes with the hotend. Dragon BMO hotend (assembled) 1 Heat…
This hotend mount is designed for the aliexpress revo six does not use the standard voron spacing and has a 22m cylindrical cooler. Note that this is for the Eva 3 for mercury one where the nozzle distance is 68 mm from the top of the…
Thanks to nhchiu and jonspaceharper for the extruder and toolhead step files and their work! I wanted to replace my Sherpa mini with the ProtoXtruder 2.0. The original drive mount for the Sherpa mini and the E34M1 didn't fit because the…
Work In Progress - Some parts not fully tested. Made these remixed parts to upgrade my Ender 5 on a budget with the option of later upgrading to Mercury One.1 or Endorphin. EVA 3 is easily one of the best toolheads out there and the E34M1…
added a bit of clearance for the bolts on the E34M1 hotend mount, as i had to break off a smidge on my print of the original added the slots for some vertical adjustment Print either as provided with supports, or with the toolhead-side…
Fixed the right side endstop model so that holes align properly. Takes m3 heat sets.
Works for 17-20mm cpap tubing
I ran into the problem that the ABL mount designed by Jonspaceharper works great for mounting the eddy coil with none UHF hotends. The distance from the bed was to large to be effective when running the Dragon UHF hotend. This was modeled…
E34m1 mercury one.1 BIQU microprobe mount be carefull with the mounting screws its not the strongest mount due to the placement
I followed the ZeroG Mercury One.1 part printing specs: http://docs.zerog.one/standard/print/settings The E34M1 tool head project can be found here: https://jon-harper.github.io/E34M1/
This design adapts the Ender 3 V3 SE/KE ceramic hotend to the E34M1/Eva 3 design. This hotend is a relatively easy to find, cost effective way to get 300C and high-flow printing capabilities with an all metal hotend design and 60W ceramic…
I've noticed the pcb mount for the 36mm boards has been deprecated and the orbiter v2.5 I'm using has a weird angle, causing the cable anchor to be tilted slightly. I've added new holes to center the mount on the toolhead, straighten it…
A remixed depressor for E34M1. Use a long screw (length depends on the distance you will need).
Requires two hot melt inserts. I placed the wiring on the outside so that it is easy to reach and has a smaller x-offset for the probe. I printed mine with ASA at 100% infill.
M2.5 x 8 screws to mount
E34M1 Toolhead Filiment Cutter ADXL Mount
Assembly drive and extruder first, then mount to front piece Extra BOM: 4x HSI 7x M3x6mm
I only found one mount for the Biqu Microprobe and E34M1 toolhead . But after installing it and calibrating, I found that it didn't quite have the mounting range I needed (since it was designed for a different toolhead I assume), and also…
I was unsatisfied with the rigidity of the pre-existing options for toolboard mounts for the E34M1 toohead, especially when using a cable chain. So I made this mount MUCH chonkier in order to improve the accuracy of input shaper results.…
Mounts a BIQU Microprobe to E34M1 using any UHF-length + single 5015 fan setup. There are a couple other options out there but I don't like the probe being right up in the front. If you're using a non-UHF setup then this will be too long.…
Released V0.2 - first released Released V0.3 - added belt grabber to front module WARNING! Do NOT use CF material to print the PCB spacer, as carbon fibre is conductive and will short the pin on the PCB, damaging the MCU board! IMPORTANT…
Installation and use should be fairly straight-forward. This mounts to the E34M1 toolhead and is for use with the CR Touch ABL probe. My design basis was the Phaetus Rapido hotend (not UHF). The probe should sit ~3mm above the nozzle in…
I printed in = ASA layer height = 0.2 first layer = 0.21 infill gyroid = 20% build plate wham bam PEX = 90c first layer 85c rest filament temps = 268c first 264c rest fan speed = 13% of total 255 NF Crazy Volcano (Mosquito Knock Off)
Modified the E34M1 Kraken Horns to fit a standard Ender Hot End
I really like the E34M1 toolhead but there PCB toolhead mount does not fit the EBB42 gen2 so I made a few chnges by rasing the shroud mount up a bit then also added PUG connection for cable relief. PUG I used…
Turbiter-SHT32 V3 back mount The idea is from Turbiter project. I wanted to print a Turbiter with an SHT36 v3 mounted on the back easily. So i designed it from scratch. You will need: 2x m3x16 hex screws 2x m3x22 hex screws 2x m2x4…
Extended cable guide to add structural support
E34M1 drive sherpa mini removed motor mount
Requires two hot melt inserts. I placed the wiring on the outside so that it is easy to reach and has a smaller x-offset for the probe. I printed mine with ASA at 100% infill.
A remixed depressor for E34M1. Use a long screw (length depends on the distance you will need).
Installation and use should be fairly straight-forward. This mounts to the E34M1 toolhead and is for use with the CR Touch ABL probe. My design basis was the Phaetus Rapido hotend (not UHF). The probe should sit ~3mm above the nozzle in…
This design adapts the Ender 3 V3 SE/KE ceramic hotend to the E34M1/Eva 3 design. This hotend is a relatively easy to find, cost effective way to get 300C and high-flow printing capabilities with an all metal hotend design and 60W ceramic…
I modded the mount from the BMO hotend to fit the Dragon Ace hotend, hope you like it! THIS DOES NOT FIT WITH THE DRAGON ACE VOLCANO VERSION, NORMAL ONLY!! Normal ducts from E34M1 are used.…
Quick remix to accommodate the 26mm blades that came with my TradRack kit (pre-cut for Filametrix length). Blade is secured by a drop of superglue or epoxy added through the additional hole placed at the end point of where the knife blade…
Its not really needed when using E34M1 top and cooling ducts, as the top offers a mount point for cable anchor. I'm using EVA3 top and bottom which is a bit narrower and EVA has a cable anchor in a different place, so I mixed up a few…
I named my ZeroG rig punisher so I have a few mods and makes I am uploading
I took the Original Highflow Front because of the Fan position. but it is meant for the normal Front so dont use the UHF Fan or Probe.
Work In Progress - Not fully tested Couldn't afford to convert to Mercury One.1 straight away so came up with these parts to gradually upgrade on a budget without having to replace a bunch of parts along the way. Remixed the E34M1…
I bought a budget Revo V6 hotend from Amazon and it didn't fit in the normal Revo EVA3 hotend. Then I found the AliExpress version had an stl file, and it fit, however, the hotend was too low. This has two different modifications. The 3mm…
A beefed up diagonal cable anchor for the E34M1 tool head platform.
A while back, I converted my Creality Ender 5S1 to the Mercury One.1 CoreXY conversion running on Marlin (initially, it ran on Klipper, but I had a problem when my RPI 3b+ failed). I found that, in trying to dial in the coordinates for…
Sheer laziness is the mother of invention And accidentally printing half of a project is the mother of remixes
If my model was usefull for you I would appreciate that you smash the like button and post your make, that would really help.
Filament sensor for E34M1 LGX Lite. Follow original model for instruction.
TZ2.0 hotend mount for E34M1 ZeroG Mercury One.1
Edit 4-11-24: Found that I didn't have the nut cutouts on the main body deep enough, resulting in it hitting the hotend insert when the belt clamps were screwed in place. Revised to make the holes deeper (so the nuts insert farther,…
