66 models
New junction box with 4 inputs. The old models had only three and two openings. Two openings are located on one side (see the pictures). This new designed 8 by 8 by 5 cm junction box (for antenna and speaker cables) features four inputs…
This 8 by 8 by 5 cm junction box (for antenna and speaker cables) features two inputs and can be securely attached to a surface using up to four screws. Seals for both cable entries and holes for securing screws can be provided with…
The combination of replacing the “kludgy” filament slot with an air-tight collet with gasket and PTFE tubing along with adding a gasket to the base groove and sealing the humidistat/thermostat with silicon makes the case near air-tight –…
New junction box with 3 inputs. The first model has only two. This new designed 8 by 8 by 5 cm junction box (for antenna and speaker cables) features three inputs and can be securely attached to a surface using up to four screws. Seals…
This screwable Adapter/Connector (5 cm) connects two junctionboxes (Bruno Germany). It is designed only for my boxes. In the case you need more then 4 inputs connect two boxes and you solf the problem. This 8 by 8 bfy 5 cm junction boxes…
The texture allowing the arms to connect to each other without rotating began to wear off, so I printed some TPU gaskets that go between the arms connections. The gaskets can hold the arms and stop them from rotating without any lines or…
Design These items are made to fit to standard fans commonly made by computer, chassis and rack fan manufacturers so that they can be more securely sealed to a fitting you are connecting it to. The gaskets are available in 0.5, 1 and 2mm…
With this plug (TPU material) you can close unused openings from my junction box. This 8 by 8 by 5 cm junction boxes from “Bruno Germany” (for antenna and speaker cables) features two or three inputs and can be securely attached to a…
New small junction box (only 45 by 80 by 50 mm) with 2 inputs. This junction box (for antenna and speaker cables) features two inputs and can be securely attached to a surface using up to four screws. Seals for both cable entries can be…
needed a quick solution for my 8kw China Diesel Heater, the gasket broke when i repaired it
These are spacers / gaskets to protect the glass behind the Geared 270 degree hinges for the K1 series by Mordiev. They were produced by taking thin slices of Mordiev's original objects so that the gaskets would have the shape and hole…
This is Gaskets add-ons for the EJ20 Subaru Engine ( http://www.thingiverse.com/thing:2451310 ). The package include : Driver Side Head Gasket Driver Side Valve Cover Gasket Passenger Side Head Gasket Passenger Side Valve Cover Gasket…
These gasket molds were designed to meet two goals. First is the need for replacement gaskets for when the original black rubber gaskets fail since the OEM is now out of business. Second is the need for an improved gasket which unlike the…
I was looking for a low profile lid raiser and RobertCowanDIY design the Creality K1 Max Lid Riser - No logo, slimmer vents got my attention. I just wanted extra security for the glass thus I remixed it by adding an additional 2.5mm to…
TPU cushions or gaskets to help minimize vibrations that affect print quality and noise levels. You can print the Nema 17 file for both the X and Y axis motors. But the Y axis will also benefit from a gasket between the plastic mount and…
Several different antennas leave a gap in-between the bottom of the antenna and the top of the t-deck plus case. These gaskets fill that gap to give the antenna installation a more "finished" look. Shown here are two typical types of…
Why: I picked up a Craftsman air compressor model 921.152101 for free - it ran but wouldn't build pressure past 40psi. Upon disassembly, I discovered blown pump gaskets. Why buy when you can make? So, I whipped these up in CAD (15…
I've been sealing the house from air leaks as trying to save money on heating. These are replicas of the foam ones I got as I ran out in the first room. To install an outlet gasket you simply unscrew the switch plate, place the gasket…
The bottom hole for the SBT90.2 is 10x11mm, so make sure you place it correctly. PLA not recommended due to 50°C heat deflection temp, starts softening. I use ASA for 100°C HDT, but PETG should be fine for 70°C HDT. Use white colour…
Cup holder "rubber" tab gaskets for a 2011 Volvo S40. The original rubber tabs for cup holders in older cars often get brittle and break off. Printed with 95A TPU at 100% Infill. NOTES: Print 2 of each part. The parts are 1.5mm high. If…
Material: TPU/TPE Flexi-filaments be like rubber with chemical protection.
Works pretty well! Includes upper, intermediate and lower gasket, scaled and based off the catalog drawing. To be printed in TPU. Eventually the gaskets swell, but since they are not subject to high heat, and they are compressed, they did…
These are printable replacement gaskets for gas can spouts. There are two different versions. The first version is with the spring-loaded spout that comes with most gas cans. The second version is with a flexible replacement spout (like…
This is a collection of various gaskets for Ford N-Series tractors (9N, 2N and 8N) manufactured between 1939 and 1952. All part numbers were found in the FO-4 I&T Shop Service manual. These gaskets may also fit Ford Golden Jubilee (1953),…
This is the same muffler designed by VzBoT but modified to incorporate TPU gaskets to further reduce noise. I used eSUN TPE 85A . Also, eSUN TPU 95A can be used, which is a little harder but easier to print. Included the modified STEP CAD…
Gasket for Bafang BBS motor. Three different Controller, the one with edge* Motor Crank body (optional) Print in TPU or similarPrint in TPU or similar * Have not had the oportunity to test the controller gasket yet. Hope it fits, please…
This is a collection of certain gaskets for Ford N-series tractors manufactured between 1939 and 1964. Currently, this collection is targeted at the 8N and 9N tractor models, but I may add parts for the 2N if I happen to come across them.…
Nothing special, printed in Overture TPU on my Ender 3 v2 NEO that has a Creality Sprite direct drive mod.
As you may or may not know, some GL1100 part are unobtainable as new parts. So, I designed these replacement gaskets for the air box and the plenum on the GL1100. I think the GL1000 uses the same gaskets, so it may fit that too. If they…
Upon request by users I made 3D-printable spare gaskets for all Rosahl M-Series dehumidifier membranes. Those include M-1J1R, M-2J1R, M-3M1R, M-3J1R, M-5J1R, M-7J1R and M-10J1R membranes. The models have the same shape as the original…
Rosahl dehumidifer membranes of the M-series come with a flat/mat gasket. However, I managed to break one of mine by not placing it properly underneath the membrane bottom and it got twisted around the mounting screws during fastening.…
remixed from https://www.thingiverse.com/thing:2997104/files, basically just cut model to make a set of gaskets
7070, 5050, 4040, 3535, 3030 Footprint. Height 0.6mm - 1.0mm. PLA not recommended due to 50°C heat deflection temp, starts softening. I use ASA for 100°C HDT, but PETG should be fine for 70°C HDT. Use white colour filament. 0.08 - 0.1mm…
Print instructions: -Set filament to TPU -0.4 nozzle, 0.2mm layer height -100% infill -When printing more than one per plate: space items out and set PRINT SEQUENCE to “by object” -Set SEAM POSITION to “nearest” Note: TPU is really…
A replacement for worn-out or lost Tama Starclassic-compatible lug spacers/gaskets. Modeled from a '90s Starclassic Maple snare drum (the painted-logo model) to replicate the originals. Fits: Tama Starclassic-compatible snare, tom and…
Sealing gasket for 6mm glass door hinges without drilling. Allows 6mm thick glass to be installed tightly without a gap. Printed in clear PETG plastic. Category: DIY
Soporte para tener organizados tus ganchos. Holder to keep your hooks organized.
The bottom hole for the SBT90.2 is 10x11mm, so make sure you place it correctly. PLA not recommended due to 50°C heat deflection temp, starts softening. I use ASA for 100°C HDT, but PETG should be fine for 70°C HDT. Use white colour…
Great for separating titanium screws from aluminum and stainless steel surfaces. Requires minimum material, doesn't stick out from underneath the cap, doesn't add too much elevation to the screw. Can be used as regular washers if scaled…
When you have all the parts printed the only assembly is done by inserting the “Thread Twister” where it belongs and threading in the “Screw V2" and then gluing the ”Screw Top V2" on top of the “Screw V2". Note: All models labeled with…
Replacements for worn-out or lost Pearl Masters-compatible bass drum lug spacers/gaskets. Masters lugs use 2 different spacers on each lug: the larger upper spacer (modeled on NP-262P) and the smaller lower spacer (modeled on NP-263P).…
A replacement for worn-out or lost Yamaha-compatible bass and tom drum lug spacers/gaskets. Modeled from a '90s Beech Custom to replicate the originals. Fits: Yamaha-compatible short split-lug bass and tom drums, such as Beech Custom and…
Was just tuning my TPU profile and made these for fun. I made these 1.5mm under the assumption that the Poron gaskets would compress slightly more than 25% from their original 2mm and 95a TPU would hardly compress at all. The TPU gaskets…
My roof rack was leaking on my Mk4 Jetta wagon, and the foam gaskets aren't available anymore. Traced them out and then printed them in TPU. Set them to fully print each piece one at a time to avoid excess stringing. There are 3 files,…
A replacement for worn-out or lost Ludwig-compatible bowtie lug spacers/gaskets. This is the thinner, longer bowtie spacer that fits the 4-7/16" (roughly 4.5") large lugs. Fits: Ludwig large bowtie lugs, 4-7/16" (roughly 4.5"). Files:…
Gasket files for intake, NT carb and magneto. The clutch cover is not in dxf but can be traced from scanned file Enjoy! Let's make parts available for everyone.
Made a bunch of gaskets for the Sarenica for a friend. Credit goes to: https://www.thingiverse.com/thing:3183449 I used his gasket maker to make these as I'm too dumb for CAD. Sizes range from 30-38mm. You may have to adjust your printer…
Mercury XR6 Poppet Valve top and bottom gaskets. Printed out in TPU and been working perfectly for over a year now. When installing, be sure to watch the gasket and make sure that it doesn't get pushed out on the thinner areas.
A replacement for worn-out or lost Sonor Force-compatible lug spacers/gaskets. Modeled from a Force 3005 to replicate the originals. Fits: Sonor Force-compatible bass, tom and snare drum lugs (modeled on the 3005). Files: Sonor F3005…
A replacement for worn-out or lost Pearl-compatible snare drum lug spacers/gaskets, modeled from a Pearl Zenithal Resonator lug spacer. Roughly 1 mm thick. Fits: Pearl Zenithal Resonator-compatible snare drum lugs. Files: Pearl Zenithal…
A replacement for worn-out or lost Mapex Armory or Saturn lug spacers/gaskets, the piece between the lug and the shell. Modeled from a Mapex Armory bass drum lug. Fits: Mapex Armory and Saturn bass and tom drum lugs. Files: Mapex Armory…
Clipsal 56 series are commonly used in Australia and NZ for industrial/outdoor/harsh environments. Print out of PLA or PETG in whatever colour you would like. Gaskets I printed out of 95D TPU Great to customise cutouts for different…
A box with 7 removable bins and 94 printable TPU seals : hose gaskets, tap washers, rings, grommets and feet. Every bin has 6 compartments with raised size labels. The lid has an engraved title. Seal types HOSE GASKET – BSP 1/4", 3/8",…
In our laboratory we are using a magnetic filter holder system to filter our HPLC mobile phases and solvents (see picture). The original gaskets are made of a foamy PE material. They wear out by repeated use and a new piece costs 4-5€. A…
Gasket for "Buffet" coffee thermos. The original one broke and the coffee got cold reel quick, and it was leaking. Printed this spare (with a slanted upper inner profile to avoid supports) and it fits nice. No leakage and the coffee stays…
An assortment of gaskets used in the Suzuki AX100 were scanned for them to be traced, but they were never really needed. I hope they're useful for someone.
Print with organic supports and some fillament which can handle high temperatures. I used PC and TPU95 for the gaskets.
These are printable replacement gaskets for gas can spouts. There are two different versions. The first version is with the spring-loaded spout that comes with most gas cans. The second version is with a flexible replacement spout (like…
In our laboratory we are using a magnetic filter holder system to filter our HPLC mobile phases and solvents (see picture). The original gaskets are made of a foamy PE material. They wear out by repeated use and a new piece costs 4-5€. A…
Clipsal 56 series are commonly used in Australia and NZ for industrial/outdoor/harsh environments. Print out of PLA or PETG in whatever colour you would like. Gaskets I printed out of 95D TPU Great to customise cutouts for different…
Works pretty well! Includes upper, intermediate and lower gasket, scaled and based off the catalog drawing. To be printed in TPU. Eventually the gaskets swell, but since they are not subject to high heat, and they are compressed, they did…
Great for separating titanium screws from aluminum and stainless steel surfaces. Requires minimum material, doesn't stick out from underneath the cap, doesn't add too much elevation to the screw. Can be used as regular washers if scaled…
printed in TPU , struggle to find replacements locally so i just printed new ones
This is ONLY the two gaskets that match where the hinges attach to the frame. Please use Just_Liberty's Gasket remix for the remaining gaskets. 95A TPU with a 0.2mm first layer, 0.18mm second layer, 20mm²/s for first layer and all outer…
