141 models
This model barely fit in the mk3 bed size, and may be a bit flexible but having support under helped You will need 6 8mm m3 screw and 6 m3 square nuts to bolt the part together. The switch is meant to slide from the front, and be locked…
Print approx. €0.21–€0.26 excl. taxPreliminary estimate for PETGSource material: PET
A simple bracket for the Netgear GS108E . It has small holes so you can see the power LED and retain access to the factory reset button. It fits very snugly and you'll have to relocate the rubber pads slightly (or you can remove them…
Print approx. €2.25–€2.75 excl. taxPreliminary estimate for one variant
This is a remix of the design https://www.thingiverse.com/thing:1322695 . I seperated the model and added some support, so you can print it also on smaller printers and you are more flexible to mount. You have to mirror the parts in your…
Print approx. €1.31–€1.61 excl. taxPreliminary estimate for one variant
I couldn't find any other designs that could fit this switch so I made my own. This design is for the v2 version that has 3 holes in a triangle pattern. The v3 chassis of the switch has 4 holes and looks slightly different. Check the…
Print approx. €0.65–€0.79 excl. taxPreliminary estimate for PETGSource material: PET
Rack mount ears for Netgear GS108E switch. Remember to hold switch while pluging cables to prevent it from moving to the back. I've added a hole on each ear for the switch feets. Inspired by: https://www.thingiverse.com/thing:249851 Print…
Print approx. €4.12–€5.04 excl. taxPreliminary estimate for PETGSource material: PET
The backstory: Tasked with the challenge of mounting a compact 5-port switch in our attic to facilitate network connectivity for our office outlet and Wi-Fi access points, I found myself with a Zyxel GS-105B at my disposal. With little…
Print approx. €3.89–€4.75 excl. taxPreliminary estimate for one variant
I needed a holder for a Netgear GS110 to fix vertically on the SKÅDIS pegboard. It also fits other Netgear GS1xx series. It uses a dovetail system (see below) removing the hassle of those pegs. It's a tight fit. I added a file with…
Print approx. €1.84–€2.25 excl. taxPreliminary estimate for PETGSource material: PET
This is a Pegboard mount for a Netgear GS108T switch. It has a 75mm spacing between the mounting holes and uses a standard 1"X1"X1/4" U.S. peg Board. Pictures are from version 1. Version 2 has the holes to reduce some of the plastic.…
Print approx. €3.73–€4.55 excl. taxPreliminary estimate for PETGSource material: PET
The tolerances are a bit tight so you might need to sand it down a bit.
Print approx. €2.21–€2.71 excl. taxPreliminary estimate for one variant
Support pour ne pas gêner la sortie d'air de la Livebox dans ma baie de brassage. Support so as not to obstruct the air outlet of the Livebox
Print approx. €0.40–€0.49 excl. taxPreliminary estimate for one variant
This is my TP-Link GS105S Ethernet switch enclosure for my printer Amiga desk. I use 4 screws 3x8mm for fixing the top You can now fix your ethernet switch on a desk or on a wall or under a shelf.
Print approx. €1.56–€1.90 excl. taxPreliminary estimate for one variant
10in rack mount for the Netgear GS-108 8port gigabit ethernet switch. Based on the 10inch_TP-Link_SG108.stl by https://www.printables.com/@mariusbach_1431080 since the TPLink SG108 is roughly the same size as the Netgear Switch. Printed…
This is a 10" rack mount for a Netgear ProSafe GS108Ev3 network switch. This model assumes you have the 4 round stock rubber feet under the switch. Printed in PLA with a 0.4mm nozzle using 0.2mm SPEED preset with adaptive cubic infill.…
The switch can be mounted under a table, on the wall or wherever you can fit 2 screws in it If you are looking for the same holder for the 8 port switch: https://www.thingiverse.com/thing:3278568 Print instructions Category: Computer…
A pair of brackets to mount a Netgear GS110TP POE-switch into a 10"-rack. As the switch is a little wider than the mountig rails in a 10-inch-rack, the switch is actually mounted behind the rails with a little gap to accomodate the cage…
I had three Netgear gigabit switches (GS105, GS108, GS116) sitting on Rack shelves. I wanted to move them off the shelves and add them to a standard 19" server rack. 1. Non-printed Parts Required (4) Server rack Cage nuts (4) M6 x 14mm…
10" rack mount for Netgear ProSAFE Gigabit switch GS108 (maybe others). It has one kestone slot on each side of the switch. Designed to fit my 10" 2020 rack. When inserthing the switch the sides will need to flex out a bit in the rear,…
Brackets for mounting a Netgear GS108 switch to the Multiboard mounting system. You will need to print 4xHandsOnKatie_Standard-Underware-Connector from the original remix file library.
This is an Easy to Print Small Holder for the Netgear GS105 Lan Switch I was Searching for a Similar Model in the Web but didn't Find anything (maybe I searched not good enough) well whatever, I decided to just make my own, the Result You…
Über den Parameter “Spalt” kann der Freiraum für den Switch verändert werden. In der ersten Veröffentlichten Version stand er auf 0,2 mm, jetzt ist er 0,5 mm und liefert etwas mehr Freiraum.
This is a remix of the design https://www.thingiverse.com/thing:1322695 . For a smoother fit I made it 1mm bigger in the inside and added a honeycomb pattern to it. The switch can be mounted under a table, on the wall or wherever you can…
I found various examples of mounts for this switch but all were bulky, used a ton of filament, or didn't use the factory mounting holes. I had one of the original metal ears that came with the switch and used it to model these. The result…
10in rack mount for the Netgear GS-108 8port gigabit ethernet switch. Based on the design from @BrianBerkley. Printed face down, 2 versions are available to be used with/without M3 metallic threaded inserts. 2 screws M3x10 are required…
For my simple Homelab, I needed a Rackmount for my old DGS-108 Switch (12 Ports, 1 Gbps). The print in in two parts : The support and the “ears” I used some super glue to fix them together. (Yeah, I used too much glue so I have white…
I just started playing around with Fusion 360 yesterday and created brackets for my 10" Rackmount.
This is a rack mount kit for the Netgear GS108 switch designed for a 10-inch rack. The kit comprises three parts that can be 3D printed without the need of support. The clamps must be secured to the main part using two small screws. I…
I had three Netgear gigabit switches (GS105, GS108, GS116) sitting on Rack shelves. I wanted to move them off the shelves and add them to a standard 19" server rack. 1. Non-printed Parts Required (4) Server rack Cage nuts (4) M6 x 14mm…
Download ? Please Like Thx BMW GS1250 Adverture
Introduction When I decided to assemble my HomeLab Rack I wanted each device to have its own dedicated holder, as I like to keep everything tidy and wanted to avoid a mass of shelves. Unfortunately I couldn't find any satisfactory…
I lost my brackets for mouting this switch in a rack, so I made my own since the other on Thingiverse didn't fit my holes. Use M3 8mm to mount them in the Switch. Print instructions Print Settings Printer Brand: Prusa Printer: i3 MK3…
Die Winkel ermöglichen die Montage von Zyxel GS1100-16 V3 Netzwerkswitches in 10 Zoll Netzwerkschränken.
I had three Netgear gigabit switches (GS105, GS108, GS116) sitting on Rack shelves. I wanted to move them off the shelves and add them to a standard 19" server rack. 1. Non-printed Parts Required (4) Server rack Cage nuts (4) M6 x 14mm…
This item is a small wall mount for the Netgear gs105 LAN switch. It is designed for the using of tesa powerstrips for the wall montage. It can be used for vertical and horizontal mount. Print Settings Rafts: No Supports: No Resolution:…
Remix from 6 inch rack to 10 inch rack
The pegs can be used to adapt the 40mm spacing to the 45mm of a Netgear GS105, or any other device with that pattern. In “reverse” order, the pegs can provide a 35mm width pattern. The holes are 3.5mm to be tapped M4 and the tolerances…
This model contains three variants of the rack mounting ears for the Zyxel GS1900-24E. First is the original, which matches the metal ears provided by Zyxel, and is likely too flimsy for 3D printing in plastic. There is a reinforced…
Some Rack Ears for the Netgear GS110EMX Network Switch to mount in a 10“ Rack. Two Variant are available to mount. The normal 1U Variant and the weird 0.5U Version. In my Case it worked perfectly but it may not in yours… I would suggest…
Not much to say about this Thing :-) It's dead easy to print, use 4 Wall_Layers, infill 20%, no support if printed rear side to plate. As always: I added Autodesk Fusion file + Step - modify as you like. Print Settings Printer Brand:…
Small single-sided 1U mount for a Netgear GS105E switch, suitable for a 10" rack. The switch measures 10.1 x 9.4 x 2.6 cm. Also fits other switches of the same size.
Zyxel GS1200-8 10 inch rack mount, remixed from the excellent model by Chillora. The remix introduces rounded corners and a centered slot to match the “rounded” rack look. Recommended to print in PETG for high thermal environments with…
A 6-inch rack mount for the Netgear GS105 and similar sized switches/hubs (94mm wide x 100mm deep x 26mm tall + 3mm feet) Inspired by and compatible with Mauker's series of 6-inch rack accessories and madmax890's models for the series.…
This mount is a combination of the Switch Rack Mount (Netgear GS105E) by Philip Hermes and the Raspberry Pi 2B/3B/4B/5B 10-inch Rack Mount by Maurício Pessoa. The two were combined to make use of the full 10-inch 1U space on the faceplate
10" Rack Netgear GS110EMX mount
A simple system of hooks to hang a Netgear GS108 switch ( https://www.netgear.com/be/business/wired/switches/unmanaged/gs108/ ) on an Ikea Skadis pegboard ( https://www.ikea.com/be/en/p/skadis-pegboard-black-50534378/ ).
Introduction When I decided to assemble my HomeLab Rack I wanted each device to have its own dedicated holder, as I like to keep everything tidy and wanted to avoid a mass of shelves. Unfortunately I couldn't find any satisfactory…
If your 10-inch network cabinet is full to bursting with technology, this holder will save you some ⅓ U space. It can be supplemented with 4 M3 inserts on the sides so that you can additionally fix the switch to the side with M3 10mm…
If you like the model, I would appreciate if you leave a ❤ like. Rack Mount Bracket for Netgear GS108 This bracket is designed specifically for the Netgear GS108 switch, offering a clean and secure fit in your 10-inch rack setup. Features…
Tipp: genug Infill wählen - (35% Gyroid reicht aus)
1U (actually 2/3 of 1U) bracket to mount a Netgear GS110MX switch (10gbps, unmanaged) in a 10 inch rack cabinet. Do not print in PLA. The heat and the weight WILL eventually deform it. I printed it in PETG with no supports. First mount…
There are already a few 10 inch rack mounts for Zyxel GS1200-8 (and GS1200-5), but this one has some unique features: As slim as possible, to squeeze it into small spots. The holes fit between the 0.625 inch and 0.500 inch sections…
1U Rackmount for Zyxel XGS1250-12. Split design for small printers. BOM: 14x M2 heat-inserts 8x M2x25 (or longer) SHCS Screws 2x M2x16 (or longer) SHCS Screws 4x M2x10 (or M2x12) SHCS Screws You'll find a full assembly which shows how to…
10" Rack Shelf for Netgear GS108T & Wemos S2 Mini Relay Board. Relay board space can be fill with an empty shelf.
this is a remix from CHARL13's model. Brackets for mounting a Netgear GS105 switch to the Multiboard mounting system. You will need to print 4xHandsOnKatie_Standard-Underware-Connector from the original remix file library.
Switch ears for NETGEAR ProSAFE 16-Port Gigabit Ethernet Switch (GS116NA) Attaching one with M3 screw holes and M5 screw holes. Category: 3D Printing
netgear gs105 mount print on its side
Modified slightly to move the switch a bit further back so this bracket can be used with Natalie T's reworked 10 inch server rack. https://www.printables.com/model/1090551-modular-10-inch-server-rack-reworked
This is a mount for the Zyxel GS1200-5HPv2 network switch so it can be mounted in a 10 inch rack. The mount is 1U high, and the switch mounts flush with the front. The total depth when mounted in the rack is no more than then depth of the…
I've used a Skadis pegboard as the backplate for my network cupboard for a while. I had used velcro to attach all of my devices - but my Netgear GS108Tv2 switch is heavy enough that it has been sinking over time, so I've made a mounting…
10 inch Rackmount Ears for Cudy 16-Port Gigabit Light Managed Switch GS1016E
Its next remix of original model.
Description The design is optimized for 3D printing. Thanks to clever angles, the model prints almost entirely without the need for cumbersome support structures—saving time, filament, and post-processing. The minimal support structures…
This is a custom 19" rack mount designed for the Zyxel GS1900-8HP switch . It features left and right mounting brackets , each split into two parts , ensuring a secure and ventilated installation. The design includes ventilation holes and…
Print the main body along with two retaining clips. These just screw in with a couple of M3 screws on the back to hold it in place.
This is a Remix of @Nightfall_536744 rack ears for the Netgear GS110EMX switch. This remix updates the design to fit with @Mauker “ 10” 3D Printable Rack Mount System ” It also adds a cut out to accommodate the GS110EMX optional rubber…
Remixed print from Thingiverse. I just opened up the ventilation area more from the the original design. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Extended Rafts: No Supports: Yes Resolution: .2 Infill: 10% Category:…
Right angle bracket to hold a Netgear GS105 Gigabit Switch that I made for use in an outdoor enclosure. This can be used where ever it is needed such a custom network panel, under desk mounting, or about anywhere.
Extended the right part (part1) by 54mm
I wanted to have a Switch in my 10" Server rack, and this one was the perfect size, tho it only came with 19" rack mounts. This model uses the original screwholes & screws to fasten, and can be easily installed in your cozy home 10" rack
Uchwyt montażowy do przełącznika internetowego model GS1100-16 Zalecam drukowanie z dużym wypełnieniem i użycie mocniejszego materiału.
I have two 8 port switches stacked and I wanted to them to hang them on my multiboard system. Due to room on my wall I preferred to have them stacked instead of next to each other, so I assembled the orginal brackets to an assembled one…
A holder to mount a ZyXEL switch onto a Skadis board. To mount the holder to the peg board, use these T-nuts .
A wall mount for the Netgear GS105 LAN -switch. The switch slides in sideways. The whole mount can be mounted with tape or you caN screw it into your wall etc.. Scale it to 102% - 105%, depending on how tight the fit should be.
If you want to attach your wifi box
Intended to match the size of the proxxon micromot mount ( 20mm) so that the Lidl drill can be used in a drill press holder made for a proxxon. A quick fix as my proxxon has a chuck and I haven't ordered collets yet. The parkside has…
Mount Zyxel GS1200-5HP v2 in 19inch Rack
A bracket for a structured media panel to hold a NetGear GS108. I know there are improvements to make, such as something to hold the back end of the switch, so feel free to improve if you even want to. Just need two pins for structured…
Compact setup for single 1U tray with both switch and media converter.
I really liked the original ESRack system design created by @EvilProphet . I created a module for Zyxel Switch GS1200-8 from the ESRack Customizable Device Mount by @DavidKahler_64887 The ESRack system includes the following components:…
A generic 10 inch 1U Rackmount for the Zyxel GS1200-8 i bought for my Lab Rax. Locks the switch in place without requiring screws, allowing it to be mounted in virtually any orientation. Upside-down, hanging in a rack or standard vertical…
This is the version of this model for normal network cables. There is a shallow version here for flat network cables. I recommend printing at 100% infill and with a raft or brim for best support.
Tplink SG108 modular rack mount likely also fits netgear GS108 requires 1u rails, recommended to print with ASA https://www.printables.com/@LvL_Dani_470947/collections/2036642
A quick and easy antenna reference point (A.R.P.) extender for Leica GS16 GNSS receivers. A great workaround instead of buying the GZS4 Height Hook. Grab a tape and measure to the bottom for a slightly more accurate height reading.…
Requirements for limiter installation ISO4762 M3 screws 10mm x 2 M3 threaded insert nut 3mm x 2
A rack mount for the Netgear GS108 switch, that fits 19 inch racks. The design is modular as it is half width, so other components could be mounted on the other half (by making a compatible mount) if you only have one switch to mount.…
Adapter innen 45,5 auf innen 34,4 mm gedruckt in TPU, hochkant drucken Adapter 45.5 mm inner diameter to 34.4 mm inner diameter Printed in TPU, print vertically
This is a cage to mount a Netgear GS108 vertically to a table using the great Desk Clamp by hein . You need to remove the small rubber feet of the Netgear switch to be able to slide it into the mounting cage. Print with supports required.
Thanks to @Vaarlion_340250 for the Original Model.
Simple under Desk Holder for LGS105 Switch
Check description of original model here: https://www.printables.com/model/793696-rack-system-module-netgear-gs108ge If you like this model please hit the LIKE button. It helps me collect the prusameters. You may also liked some of these…
Description @EvilProphet made a really nice system called ESRack. Expanding on it. The ESRack system includes the following components: Mounting Brackets - used to install the unit in the rack, available in 3 sizes: Short Medium Long…
This custom wall-mount plate allows you to attach the Netgear GS105E switch directly to a wall surface using only a stapler. Designed for quick, tool-free installation, it keeps your network setup tidy while avoiding damage from drilling…
This is the shallow version of this model for flat network cables. There is a deep version here for normal network cables. I recommend printing at 100% infill and with a raft or brim for best support.
Based on a Makerworld posting adjusted for two switches
I created this for to work with the Mini Server Rack, which can be found printables.com/model/108975-19cm-network-rack I printed it with PETG, worked pretty well. a little tight I forgot about the feet to the switch when I was modeling…
Battery store for Leica GS15 case
By default this type of switch comes with a rack mount, but i wanted to mount it on a wall vertically. You might need a slightly longer screw, the original is a bit short with this()i believe its a M4 screw. I guess it should work with…
A friction wall mount for the Netgear GS108E 8-port switch. Attach the model labeled “SwitchSide” to the switch using 6-8 mm long M3 screws. The cavity on the switch should be deep enough to allow an M3 nut to fit in the wall mount slots.…
By default this type of switch doesn't come with either a rack or a wall mount, but i wanted to mount it on a wall vertically. You need an M3 screw, at least 10mm long. I guess it should work with other switches from the same…
