Counting matching models…
Want to try dual idler and it looks fun, if you did any test compare with single idler please let me know. 2 ver 4 bearings or 6 bearings. Original plan was to use 672ZZ(2mm ID) bearing but too hard to get, switch to 681XZZ(1.5mm ID)…
These Idler blocks lets you use M5 hardware to tension your belts. You need 2xM5 nuts and 2x M5x20 bolts. The Idler towers needs to be drilled out with a 5-6mm bit to make room for the bolts.
english :If you are looking for a pulley that doesn't make noise for your cr10, and that has conical tabs, here is your file, I looked online for a compatible file for the printer and couldn't find it, so I decided to model it For those…
Hello XL makers! This is a Remix for the Prusa XL Y-Carriage for toothed Idler Pulleys with a width of 10mm. I have written a detailed article about this, which deals with Gates' manufacturer recommendations:…
This upgraded idler stack is designed specifically for the Modix X-axis and offers significant improvements in durability and stability compared to the original design. You can find the product here. UPDATE 10. June 2025 Added a spacer…
Adapter (spacer) 3mm bore to 4mm diameter 8,5mm wide M3 screw to 4mm bore pulley
Use at your own risk, this is a prototype. It will not hold up to long term use. I did get more miles than I expected out of mine, but unless you print it out of an exotic engineering filament or modify the design to work for metal, this…
Kreidler Florett RS K 54/504 N Supports: Yes Resolution: Dynamic Infill: 20% line Filament brand: 195 - 210 Filament material: PLA
Want to try dual idler and it looks fun, if you did any test compare with single idler please let me know. 2 ver 4 bearings or 6 bearings. Original plan was to use 672ZZ(2mm ID) bearing but too hard to get, switch to 681XZZ(1.5mm ID)…
Um das Filament sicher in den Verteiler führen zu können, habe ich die Filament-Zwangsführung IN den Original-Idler eingearbeitet. Bei andere aufgesetzte Führungen müssen alle Idler-Teile neu gedruckt werden und passen nicht mehr. Die…
Um das Filament sicher in den Verteiler führen zu können, habe ich die Filament-Zwangsführung IN den Original-Idler eingearbeitet. Bei andere aufgesetzte Führungen müssen alle Idler-Teile neu gedruckt werden und passen nicht mehr. Die…
Um das Filament sicher in den Verteiler führen zu können, habe ich die Filament-Zwangsführung IN den Original-Idler eingearbeitet. Bei andere aufgesetzte Führungen müssen alle Idler-Teile neu gedruckt werden und passen nicht mehr. Die…
Here is my variation of smooth idler for HGX extruder. Original idler arm was changed to use smaller bearing(16mm) as original gear is 18mm. BOM: 625 bearing 20mm pin(could be reused from existing arm) Print settings: Default voron print…
Original Idler Bracket for Flashforge Adventurer 3 Y-axis / Bed. Reverse engineered with manual measurement for upgrade purpose Recommended Print Settings: Material: ABS Infill: 100% Assembly Guide This part can be found near the rear of…
This mod is UNTESTED and is a modification of the Prusa Core One's CAD files. I am not responsible for any damages done to your printer, please use this mod at your OWN RISK . This mod will help eliminate VFA (Vertical Fine Artifacts)…
What do these blocks do? They allow the use of toothed idlers that will drastically reduce belt pitch vfa Can reduce rattling noise on fast accelerations (seems to depend on material used for printing) Easy servicability of belts and…
Made the tool taller to 10mm to work better with the 11mm wide idler pulleys that uses the GT15 9mm wide belt on the QIDI Plus 4. Also removed the PRUSA Printer script and added the QIDI wording & logo to the tool handles. Printed in…
I extended the guidler arm to be able to lift off the idler if needed. I also increased the hole diameter for the anti-squish for better tool access when adjusting. The arm was increased by 15mm.
Print with TPU at 100% infill. I used a small bench vise to install it. It is a interference fit to the bearing.
Genuine Gates idlers are slightly wider than the ones Goyetus's Y-Axis tensioner bases are designed for. I have remixed the original 20GT base to be compatible with such idlers. Thanks to Goyetus and MattyVee for this excellent tensioner…
Provides an upgrade to a 608 bearing on MoonCool TK1 bikes. Use at your own risk. Better idea: don't buy a mooncool - worst build quality I've seen on a $1000+ product. Cheap off the shelf foreign components slapped onto a frame.
The second Voron 2.4 printed part needed following the build guide
Third stage print and build for gantry printable parts split into base colour and accented colour.
This is a modification based on the set of parts used to upgrade your Prusa MK3 / S / + with MK4 style parts. While assembling the upgrade, I found out that I do not have the needed 'pin' for the idler so I made a small conversion, parts…
We have a Fusion F410 at work and have had several issues with it over the last two years, particularly with the 3d printed parts. We recently had a rash of feed errors only to find the plastic wheel was grinding against the encoder base…
I designed this wheel based on the aluminum wheel that comes standard with the XYZ Da Vinci. I own two printers and both have had failures with this part. I previously attempted to re-design the whole plate to accept a bearing. This…
This replaces the bottom idler bracket for KevinAkaSam's Belted Z Mod for an Ender 3 Max. The original bracket is an L shape and made for the Ender 3/3 Pro and other's where the gantry uprights mount on top of the base. The E3Max has the…
Adaptation of the 20mm axis for the bearing belt holder.
Remixed the standard R4 version of the idler to remove rattling sound when idler moves. Remix of the Ultimulti version here: https://www.printables.com/model/893656/ Print as oriented. This remix adds a .5mm bearing spacer to each wall of…
This is a simple jig used to cut the 5mm rod required for the pins mod found here: GitHub - clee/VoronBFI: Beefy Front Idlers (for Vorons) This jig will produce: -22mm (4 required)
Join the EnderXY community on Reddit: https://www.reddit.com/r/EnderXY/ I'd recommend printing in PETG at least. I've orientated all the parts ready for printing. This is compatible with my RenderXY modification. If you've managed to…
Hey! Unfortunately, the mmu2 version don't work with the mmu3, and since i wass a big fan off the mmu2 idler door part i did a remix off the original part to this one. MMU3 version! Print it in PETG 20% Grid Infill at 0.2mm layer hight. I…
Idler mit kleinen Verbesserungen, da bei mir der Filamentwechsel nicht 100%ig sauber lief. Als Ursache hierfür konnte ich den orginalen Idler ausmachen, da in der oberen Lagerung durch die Bewegung das Loch aufgeweitet war. V1 Um dieses…
I really like this Y axis overhaul, and I even bought a toothed pulley according to the instructions; however alas, in my country the one I was able to source was much slimmer than what the model was made for, so I remixed the Tension…
Remixed this holder to hold a 10mm wide idler pulley. Use of this idler helps minimize belt ripple in your prints. https://www.filastruder.com/collections/hardware/products/gates-2gt-idler?variant=41017736724551 Gates 2GT Idler Toothed…
I really like the ProtoXtruder 2.0. Unfortenatly there is only a short idler arm which does not allow manual filament changes. Since I implemented cold filament changes in my macros, this is really important for me. So I just created this…
These Idler blocks lets you use M5 hardware to tension your belts. You need 2xM5 nuts and 2x M5x20 bolts. The Idler towers needs to be drilled out with a 5-6mm bit to make room for the bolts.
Double Helical Gear Mod on BFI (Beefy Front Idler) It has been modified based on Diyshift's BFI Gears user mode I made it to deliver better torque and prevent it from being twisted than normal gear The single-helical gear was found to…
Attention: This ist for the old O-Rings! I will make new Version for the new O-Rings soon. This is a remix from @racerethan ( Prusa XL Left and Right Carriage With Gates 20t Idlers 3mm von racerethan | Kostenloses STL-Modell herunterladen…
A beefier version of idler holder for V400. See original model for more details
The standard Daylight mounts dont work with Clee's Beefy Z Idlers. (BZI) so I made up a quick replacement.
Updates 25-10-22 “Idler_6-7_R3” dimensions adapted to the Main Plate R4 with angled Swivel. This update is more angled than the previous design to align the screws horizontally and minimize the screw tread friction in the heatsink.…
Missing clutch handle for this cool Kreidler Florett Model. Printed with Resin, but with FDM ist also possible.
If the two loosely connected idler-swivel halves bother you, this modification is for you. The original mechanism is brilliantly designed and I don't intend to change that - my modification only improves the connection between the…
english :If you are looking for a pulley that doesn't make noise for your cr10, and that has conical tabs, here is your file, I looked online for a compatible file for the printer and couldn't find it, so I decided to model it For those…
I adapted Toolson's great design to accomodate the 624 bearing that matches the belt pulley more closely. The mount points are also 1.5mm closer together to match my P3Steel.
This adapter is to use the smaller 624 bearing instead of the 608 that the Z-carriage was designed for. The 624 matched the diameter of the belt pulley more closely. Needs an M4 bolt and nut. The washers slide onto the inside of the…
This idler pulley / roller is made to roll freely while supporting a roll of filament. It takes a 608 cartridge bearing with a 8mm (5/16") bore. The rolling surface is 28.6mm (1-1/8") in diameter. Also included is a bearing insertion and…
Print the ‘rb arm’ file lying flat and push the tube into the 4mm hole on a square face
This is my “version 3” of TypQxQ's double sided XY idlers mounts for the Hypercube Evolution 3D printer design that uses mostly square nuts. Big changes in V3: Functional: Trimmed the guide protrusions that stick into the 3030 slot on one…
These are replacement front idlers carriers for BFI 2.4. Check both to see which has the better fit Two Files: BFI-carrier-big-x2: Increases all the head screw dimensions by .5mm bfi-carrier-head-height-.4mm-higher: Increases only the…
The Voron 2.4 2WD Gantry introduces a groundbreaking design that sets it apart from other 2WD systems available in the market. Here’s what makes it unique. 1. Shorter Belt Paths for Greater Efficiency: Unlike other systems, the mammoth-3D…
A printable Timing pulley with 2 fixing screws for 5mm Shaft
Changing the filaments on an MMU3 can be a real pain, especially if try to do it with the Idler Body closed. When the filament is fed into the MMU3 Pulley Body, it may not align with the pulleys, and the Idler Body bearings may not…
I grew impatient after I received my RIDGA set but the pack of idlers were not delivered yet so I found some bearings from the drawer, measured it and started remodeling the idler arm to fit the bearing so I can already start testing the…
Someone asked if I already had this due to my other window quilt pulley upload, and it turns out it's one of the first 3d prints I designed from scratch back in 2015ish. Turn on supports to print it, and give it lots of perimeters and…
I designed these covers as I have had to replace one or both of these idlers every single year. Snow packs up inside the pulleys during use and then melts. The melt runs straight into the bearings where it sits all summer long rusting up…
This is the Y axis on a X max 3 with significant strength upgrades. Use the existing rods and pulleys off the originals. there is a lot of supports used. I have attached a .3mf file as an example. ( you can print this and be happy ) 4…
Hello XL makers! This i a Remix of a few Remixes :D Thanks to all of them <3 Lukáš Kupec , sshyshak , Racemade3D , racerethan , Prusa Research This remix was made for pulleys from LDO or Gates that have a thickness of 10mm. The original…
Hello XL makers! This is a Remix for the Prusa XL Y-Carriage for toothed Idler Pulleys with a width of 10mm. I have written a detailed article about this, which deals with Gates' manufacturer recommendations:…
NOTE: This is still being updated as I have other ideas to implement and would like to make it more modular for different filament spool locations. There are a lot of filament guides for specific situations but I couldn't find exactly…
This upgraded idler stack is designed specifically for the Modix X-axis and offers significant improvements in durability and stability compared to the original design. You can find the product here. UPDATE 10. June 2025 Added a spacer…
Print material : PETG recommended. Use organic support on build plate only, 40% grid infill recommended. Prints fine with 0.20 STRUCTURAL profile with 0.4mm and 0.6mm nozzle. In order to secure the metal pin when finishing building the…
Introduction I noticed a deformation of the belts. It's moving forwards causing the belt to be a few millimetres out of alignment. Consequence: the Z height cannot be respected without a correction in klipper (with distance_rotation ). My…
Adapter (spacer) 3mm bore to 4mm diameter 8,5mm wide M3 screw to 4mm bore pulley
This adds a thread to the Idler Body as one of the other metal pin kept moving to the outer side, blocking the mmu3 sometimes. Recommended Print settings: 0.20mm Structural, 0.4mm nozzle size Organic support on build plate only Use a M3…
Remix from madsoul666's model. Added cutout to allow the arm some clearance. Added cutout for ziptie Added PTFE tube stopper to prevent the tube go too deep into the bearing. Use MR95zz bearing for the motor shaft and a grooved bearing…
The same as hprotzek's design but with cutout and washer to keep the base from pressing into the sides of the idler. For 5mm bore 2gt 20th tooth idler from E3D. The tensioner was designed for the mk3 so you will need the mk3 belt mounter.…
Had an OEM IDGA gearset laying around and I had nothing else to do with it. Clockwork2 seemed to be unecessarily complex so I opted to butcher WristWatch2 BMG version to make it fit IDGA as it's already fairly similar. Just needed to move…
4.5mm Ball Chain Idler for Blinds - Simplified Design This is a remixed version of the AM43 Blind Motor Variable Drive Pulley, redesigned to function as a passive idler for 4.5mm ball chains. Unlike the original motor-driven design, this…
Dual gears are not the holy grail, as MirageC and MihaiDesign showed in their videos. There is always a bit of backlash and usually a single gear can provide enough torque. This is why many modern exruders are now going single gear. A…
Update 15.02.2025 I still got problems while calibrating the sensor. Finally I guess the main problem is not the idler but the main plate. With MMU there is another type sensor to detect the filament. It triggers on the movement of the…
I love my MMU3, but too often when loading the filament to the MMU it misses the output tube and sticks out between the idler and selector (see picture). This mod adds raised ridges to the idler ensuring filament remains on the right path…
I modified the "X-End-Idler-Tensioner" to work with a M3 Screw with cylinder head / Socket head cap screw.
This part replaces the idler mount from this project to allow the installation of a 400mm linear rail, this enables the left toolhead to be able to print on the entire print area of the printer when the right toolhead is parked.
The original toothed and F623 idlers attach to where the 2040 and 4040 extrusions cross each other on the Ender. Some printers do not have this type of attachment (such as my Biqu B1 SE). This is a modification of the lower idlers so that…
Gates Heavy Duty Idler Pulley Working model created to aid in printer part design changes. When you are designing your pulley holders to upgrade to this pulley, you can add this accurate model to your design to make sure it fits. This…
Gates Heavy Duty Smooth Idler Pulley Working model created to aid in printer part design changes. The Gates idler is far more durable and reliable than the usual imported pulley found on most printers. This version of the pulley is…
Some parts can be printed for color customizations. Please print using standard Voron parts print settings
This is a small adapter spacer to widen the idler Filamentalist 80mm idler roller to fit the QuattroBox MMU. I had already printed idler rollers for the Filamentalist Rewinder and it felt unnecessary to print new male and female ones for…
Prusa MK4S Gates X-Idler Mod Modified to accept the Gates heavy duty toothed idler pulley to increase reliability and reduce belt crushing. Gates PowerGrip idler is designed for use with 6mm wide 2GT belt tooth profiles. Idlers contain a…
Why is the clearance for pins and idlers are soo tight?! Created this print because it was hard to get the pin aligned properly before pressing into place as any slight offset can make it harder to insert into the idler. NOTE: very snug…
Idler pulley (containing a B623ZZ bearing), for BQ Prusa i3 Hephestos ’s X- and Y-axis belts (6 mm GT2). I find that this remix of juanjaem’s Support for B623ZZ (BQ Prusa I3 Hephestos) fits better (when printed on my Hephestos). I think…
Cutout allows access to idler screws which need to be adjusted for running TPU on the XL.
Needed to create a thicker idler roller as found out the hard way, card board spool was getting stuck on the side of the box.
AnyCubic K3 Combo Idler Gear Replacement Guide A few weeks ago, I ordered two AnyCubic K3 Combos. Unfortunately, both arrived with broken gears in the idler mechanism. The issue presented as excessive clicking and popping noises when the…
General When printing particulary brittle filaments like PET-CF the two idler wheels on the Nextruder can intruduce too tight bending radii and inturn break the filament. This is a Drop-in replacement for Nextruder idler lever. Based on…
This is a redo of my original x-tensioner so I could replace the idler bearing with a geared bearing to reduce belt vibration. This uses the same 5mm hardware that came with my printer. This is made to use a GT2 20 teeth idler pulley with…
This is a set of adapted V2 BeltClamps if you use the ChaoticLabs Carbon Fiber Bracket Kit together with TorxFighter Zero offset Clamped GE5C Mount for Voron 2.4 + Beefy Front Idler The V2 BeltClamp design is used where possible and the…
What is this: For MK4S / MMU3 nextruder idler lever. lever A/B mod: I think the original nextruder idler lever is a little bit too lose when locked. in some cases it may even falsely trigger the magnet sensor since it's too loose. imagine…
Features: Open/close Idler-unit without tools Idler-body locks with Snap-locks Original screw, spring, spring movement etc. Easy to exchange with original Idler-body Filament sample holders, and number imprints Easy assembly/disassembly…
These toothed idlers actually did absolutely noting . The test benchy came out completely indistinguishable from the non-toothed idlers. The non-toothed flanged bearing is also much stronger, 100% metal, is able to take more torque, and…
Read somewhere there's a possibility, that the springloaded locking screw can work it self out, because of all the shaking when loading/unloading filaments. So i made a small locking clip, to ensure that this doesn't happen. The clip sits…
Use at your own risk, this is a prototype. It will not hold up to long term use. I did get more miles than I expected out of mine, but unless you print it out of an exotic engineering filament or modify the design to work for metal, this…
The original front idler towers were too flexy for my build, so i designed a bracket to further stiffen them. Print one for the left side and mirror it for the right side. Use general Voron/zeroG settings for the print. Additionally…
🚀 Quick Spotlight: EnderWire Beefier Square Nut Y Idler If you're building or upgrading a Voron-style EnderWire/SwitchWire printer, here’s a golden opportunity to beef up your Y-axis. Enjoyed the model? Help me save up for another Voron…
Slightly modified to remove the linear rail groove. When printing these pieces in high temperature plastics, it was impossible to scale the part to match the rail grooves. Also provides a little more alignment room when assembling.
Voron Trident modded (remix) a and b gantry joints to use steel dowel pins as shafts for idle pulleys.
Voron V0.2 Tulip Idler LazyCam NoPin mod Hardware needed: M3x16 BHCS and M3 hex nut
![Rook 2020 MK2 & Scalable MK2 M5 Idler blocks [MK2]](https://media.printables.com/media/prints/1034193/images/7845167_bfd54e39-994f-4069-a3c6-44e2b49c3e21_a10bfcf2-06be-4ddd-98e9-dd113f4ce1a2/img_20241009_125921.jpg)
