108 models
Made this simple conversion to be able to keep the M18 Inflator stacked on a Milwaukee Packout. The rubber feet can be reused with an M4 heat set insert and a M4x10 screw. UPDATE 5/18/24: If anyone is interested in purchasing the print…
Polymaker Matte PLA Filament 1.75mm Army Red is a good color match for Milwaukee Updated 1/20/24 - removed a small hole artifact from the middle. Thanks to @MatthewSlay for the heads up. Also added a STEP file
Hang your Milwaukee Inflator on the wall and make it more available.
Should print on FDM without support, I printed using automatic settings on my SLA and the output was spot on
Now available for purchase on my Etsy store . We use the Park Tool INF-2 inflator at the bike shop and wanted somewhere to keep it so it would always be easy to find. I made this holder which screws to a 4x4 support and holds the inflator…
I needed a way to use a bike pump to inflate an air mattress. So I made a conical adapter to a Schrader valve (normal car or bike tire stem). I used ninjaflex to get a better seal but I am guessing pla or petg would work well too since…
This is a fine tip nozzle for the Ryobi low-pressure inflator. It's great for using the inflator to clean out small electronics such as a PC case. This is a simple design but it was used as an example of how to use the 'Sheet Metal'…
Simple replacement nozzle adapter for "Ryobi R18VI-0" and “Ryobi P738” Inflator Does not need any print support. Air nozzle diameters 5mm and 7mm. Step files are included for easier remixing.
A simple two hole version that just hangs the inflator without the “safety latch” portion. Includes files with no holes, 40mm holes and 80mm holes. Print on end as pictured, no supports needed.
I made this so my kids could inflate balloons without any help. Enjoy! -Bush3D
This wall hanger uses 3 screws to secure the mount to the wall. It will hold the Dewalt tire inflator with or without a battery inserted.
This is a part I designed for the Ryobi P747 dual inflator. It enables you to use the tube for a Bravo branded hand pump (Tends to come with a lot of inflatable kayaks and SUP boards). This is only for the low pressure/high volume side of…
Wall brackets for Ozito (Einhell) PXC 18V Workshop Blower and Inflator. I designed these wall brackets for the Ozito (Einhell) PXC 18V Workshop Blower and Inflator and associated accessories. There is provision for a dowel pin in the…
Ryobi Inflator R18MI has a mattress inflating hose with a short stump of a connector that doesn't fit well in some mattresses. This adapter lengthens and increases diameter of the stock connector.
Just a simple tool that makes inserting a new O-Ring into an inflator quick coupling much easier. The needed O-Ring size is BS610 (6,75x1,78mm). Pull the coupling ring back as if you would when connecting a BCD and insert the pin with…
This is a "do it yourself" solution for a pump bag to inflate the new Therm-a-Rest air mattresses (e.g. NeoAir XLite). What to do? print both parts take any bag and cut a small hole in it. put part 1 (body) through the hole from the…
This is an attachment for the Ryobi 18-Volt One+ Cordless High Volume Power Inflator (Model P738) to connect a garden hose to the inflator so it can be used to blow out residual water from a hose at the end of the season. To use: place…
I love my Ridgid tools. Especially the Lifetime Warranty - even for batteries! My most recent is the Inflator tool with digital display and automatic shutoff.…
*************************************************************************************** ************ 2026.03.25 more riggid version (v04) ************ ***************************************************************************************…
This is a inflator adapter that allows you to attach a shop vac with an ~33mm OD hose connector. I use it with a Milwaukee M18 Non-Packout shop vac, you can use the exhaust to inflate, and the vacuum to fully deflate. I print with the…
Trigger parts printed in PETG, 0.2mm layer height, no supports. (Optional) Strap printed in TPU, 0.2mm layer height, no supports. Attach the cap to the narrow end of the insert. Place the insert into the housing as shown. Place the other…
Now available for purchase on my Etsy store . I originally designed this holder for the Park Tool INF-2 inflator we use in the bike shop, and it works, but our air hose comes down from the ceiling. Holding the inflator "upright" meant the…
This is a trigger guard for the Ryobi P737D 18V inflator. Found it'd get triggered sometimes when I'd toss it in my trunk when going biking. Printed in two pieces to increase the strength of the parts. Can attach with a single screw, but…
Description This is an adapter that converts from a female Schrader valve into a WD40 compatible adapter if the WD40 can has run out of air but still has solvent. There are 2 versions: One without threads and one with threads. Use the…
The Ryobi P737 pistol grip inflator has an attached hose that is super short and impossible to stow well. I used tinkercad to create a pin to fix the hose to the tool better. There is some interference between the pin and the hose itself,…
Lost the high volume hose adapter from my ozito inflator so made a new one, while i was at it designed a SUP inflator to screw onto the original hose aswell. Category: 3D Printing
I wanted to design a Pool Inflator adapter to use with my air compressor. This uses the standard tire inflator tip screw. You can use this with most air compressors, and bike pumps. Print Settings Printer Brand: Creality Printer: Ender 3…
To see how it works check out this video: The printing requires no special precautions, it works great with PLA. The inflator is best printed with the thick part on the plate. No support required. Please note the following tips: Use the…
I created a more 3D-printing-friendly custom nozzle attachment method for the Ryobi P738 inflator (FDM nozzles replicating Ryobi's design tend to split along layer lines over time). This model is a nozzle that's equivalent to the inflator…
I got a Ryobi high volume inflator and I needed to blow up a 2.6m dingy. Annoying it didn't have the correct adaptor and only had generic ones. This is an adaptor which will fit directly onto the inflator and into the dingy ports to…
As covered on CyclingTips.com , this is a small bolt designed to attach a Co2 inflator head to the base of a Specialized SWAT-friendly bottle cage (e.g: Rib Cage II). I have only tested it with a small handful of minimal Co2 inflators and…
Simple shelf to hold the dial Inflator / deflator.
We have a lot of these blowers at work, but all the nozzles have disappeared. In an effort to teach myself Fusion360, I've recreated these nozzles. Support Free Will fit the Milwaukee M18 compact cordless blower, and I'd assume they'd fit…
The bayonet adaptor on my inflator broke so the bayonet would no longer attach. So I designed this replacement. It also fits into the deflation port. I have the CIT1800G inflator and it fits perfectly, but it looks like the P747 has a…
This is a replacement foot for my Milwaukee M18 Inflator. I lost a foot almost immediately, and the replacement parts were hard to find. I printed it in Overture 95A TPU.
This is an attempt to create a parametric (customizable) OpenSCAD nozzle for the Ryobi high-volume low-pressure inflator that can be adjusted to work with a particular inflatable. The tip that comes with Ryobi is about 7mm, while most of…
This is an easy print, no support, 0.2 layer, 100% infill, 0.4 nozzle, flexible material e.g.: TPU. I release the CAD files, the STL, and g-code for Prusa MK3S. Happy printing, and dive safe.
Designed this part to hang my new DEWALT DCC020I inflator on the side of my Craftsman toolbox. I also created a variety that will screw into the wall using four countersunk holes. I'd print using PETG if you're using out in a garage or…
This design is for a more 3D-printing-friendly custom nozzle attachment method for the Ryobi P738 inflator (FDM nozzles replicating Ryobi's design tend to split along layer lines over time). The adapter doesn't permanently modify the…
This adaptor allows for hands free inflation of your Alpacka packraft using a FLEXTAILGEAR Evo Air Pump . It uses a friction fit into the inflator valve and should not require any additional seals or gaskets. Material and layer height…
This Tube Hose Organizer for the Dewalt Cordless Air Inflator (DCC020IB) is a practical and efficient accessory designed to keep your air hose neatly stored and easily accessible. This organizer prevents tangling and enhances the…
Wall mount for the P737D Ryobi Inflator. Angle of the arms allow storage upside down and will keep it in place.
Add-on storage for your 2848-20 Milwaukee M18 tire inflator to hold two right angle inflator chucks. Use as is with the chucks below, or customize to fit your preferred chucks. Most chuck adapters should fit fine in the small hole. Uses…
Designed to adapt this inflator: https://a.co/d/822qV8A to this camping air mattress: https://a.co/d/6FwTX7u Inflator had an output with an outer diameter of ~37mm, air matttress inlet had an inner diamter of ~27mm, so this adapts them.…
This design is a variation on my more 3D-printing-friendly custom nozzle attachment method for the Ryobi P738 inflator (FDM nozzles replicating Ryobi's design tend to split along layer lines over time). It adds storage for a spare nozzle…
Side covers for Ryobi R18MI inflator. Right cover with air vent so mattress inflator can be used with the cover on.
Co2 inflator storage spacer allows you to store the inflator on the co2 cartridge without puncturing the seal on the cartridge. A similar spacer is included in some retail packaging for the pictured Specialized inflator, but I misplace…
🚐 Inflate your Quechua mattress with a car compressor This adapter allows you to inflate a Quechua Air Basic 140 cm 2-person camping mattress using a pump or compressor with a standard car tire (Schrader) valve connection . The original…
Small adapter to attach 7/16" OD flexible tubing to the Ryobi high volume cordless inflator. Tubing should slip right in the front, and I use a bit of CA glue to hold it in. Im sure tubing varies a bit, but this should be close. Print…
ARB Digital Tyre Inflator holder for mounting inside your 4x4. Printed using TPU - requires thick sidewalls and dense infill Requires some Velcro tape for mounting and securing Printed using an Ender 3 S1 Pro
Ryobi P737D Inflator Trigger Guard uses existing screw holes on the side of the inflator. The original screws are not M3 machine screws but two M3 x 25mm machine screws work perfectly for this modification. Printed with Inland PETG on…
There's a video here: a 3D printed version for a tool that helps with replacing the internal Oring in the inflator's hose end. This Oring is known for being very difficult to align in it's grove. Category: Hand Tools
Bicycle support for Decathlon pump. The diameter of the pump is about 29 mm, while the diameter of the hooking slots is 20 mm. Print it vertically with supports and the slots turned to the right or left so that the tensile strength is…
Printed with PETG with supports Z=0,2
I wanted a small container that would protect the CO2 cartridge and valve while packed in the bottom of a pack or tool box. I discarded containers that had mechanisms for securing a lid if they could be broken or easily opened. I printed…
A simple pass through adapter for adding a heating gland to a drysuit. Please note this is not designed as a printable part necessarily, but rather I assume it to be CNC milled from acetal or similar. Chamfers and main threads are not 3D…
I made an adapter to connect my Duotone Kite hose to my Hoto Portable Tire Inflator. It should fit a standard bike pump as well
Material: Any Infill: 50+ Print as is no support, brim most likely needed
Tip for Leaf blower to inflate swimming pools, air mattress and other inflatables. Fits Toro electric leaf blowers and other leaf blowers. May need a little tape to help hold it on during use. Inflates pools/mattresses FAST! Print…
I saw the alpenblow and was curious whether it would work for me, but not curious enought to spend €60. So I made my own. It weighs 16g and takes about 3 minutes, 12mAh, and 2 extra breaths to inflate my Nemo tensor regular wide.I saw the…
My screw backed off, and I lost the lever. I had to purchase another Inflator. I used the new lever to take measurements and create this model. This was printed in white ABS for durability, and in case it is left in a hot vehicle. If you…
I wanted a wall mount for my inflator, i designed this. printed in petg
Adapter with large valve tip for inflatable pool. Look at PDF file for dimensions.
The M18 inflator with pack out feet. It uses the original screws.
So my Flextail airpump kicked the bucket (died) a week before a backpacking trip, wasn't in the mood for sketchy lipo rescue and don't have enough time to order another one, yay!. So I printed this to dig myself out of a hole and…
A holder to hang the Milwaukee M12 inflator on Multiboard. The hooks support the handle and the buttom of the inflator rests again the Multiboard tile I have used the heavy weight-bearing hook snaps from Multiboard, but I think the…
PETG recommended at .2mm maximum with minimum 20% infill.
This is a replacement inflator adapter for the Ryobi 18v High Volume Inflator.
Support for decathlon bicycle pump, easy to print, I recommend PETG because it is for outdoor use, it can be fixed to any bicycle with plastic ties
This is a Backpacking Inflator for a Therm-a-Rest backpacking mattress like the x-lite. It is very lightweight and therefore somewhat fragile. Take care. I recommend printing the body with a 0.4mm nozzle in PETG and the impeller with a…
Loved the concept of the holder for the other tools, so I made one for my inflator too
Pretty self explanatory. Can use the hardware on the stand.
Adapter for e.g. Ryobi R181 inflator/deflator. This adapter can be used for automatic life vest testing. Place the the adapter to the curly tube of the pump, fill up the life vest via red tube, let it stand min 24h, should stay firm (- if…
Used to print in PETG 15-20% infill 0.2 height
Print two of these and they should line up perfect with the bolt holes in the ENVE Tire Inflator. Holes are countersunk so the screw heads should not rub on the GearTrack. The bolts that are included (m5) to hold the inflator to the wall…
Screw on cap to protect the cartridge tip and threads. I use these in my bike tool pouches and containers. Fits standard 16g and 25g inflator cartridges. Threaded UNF 3/8". If it works for you, please Like and post a Make with photo for…
Slip on sleeve to protect your hand from freezing during inflation. More compact than neoprene/foam alternatives. Provides nominal protection from cold. Fits standard 16g and 25g inflator cartridges. I print with 3D Honeycomb infill at…
This cap and plug fit SeaQuest, US Divers, Aqualung and other BCD inflator and port as well as the quick dump valve opening on the back. The thread size is imperial 2 1/8-12. They are useful to protect threads if one removes the inflator…
!! Work in Progress !! This is an adapter do be able to use my boat/standing paddle inflator to inflate an intex air mattress. Inpired in the design: “Adapter for Makita DUB186Z blower to inflate Gumotex boats fast by Nathan”, (but build…
I keep an inflator chuck near my bikes in my workshop so I can quickly top off the tire pressure before starting a ride. I used to tuck it behind a piece of Romex wire on the wall (LIKE A CAVE MAN) but now that I have an MK3S+ and I know…
No one makes an inflator for the Cascade Mountain Tech mattresses (sold at Costco). This adapter will slip over the outlet of a Big Agnes pumphouse bag, and fit tightly into the mattress valve. This is designed to be printed in PLA--the…
The Rokit Up is a fairly compact inflator, but the hose is easy to lose if you don't want it poking out of the top all the time. This clip sticks to the back (it's 24mm wide, the same as a roll of 3M tape), and keeps the hose safe.
I use this inflator in my woodshop as a convenient way to blow off sawdust from projects and work surfaces. This rack/holder mounts to the wall and makes it easy to grab when needed. I printed it with PETG and a 0.25mm layer height, 25%…
Keeps your M12 inflator and Locknflate quick release a bit tidier. I've include 3 models with different clearance, to make fitment a little more customisable. 18.0, 18.1, 18.2mm, I used 18.1mm with a dab of super glue and doesn't budge.…
Probably the most basic Thing ever, but it works The Ryobi inflator is great, but whenever you pick it up you almost always press the trigger. So this is a VERY simple trigger guard. I did a more complex one (Fancy Trigger Guard) but…
An adapter for a portable inflator to inflate inflatables. Covers up to a 2in hole.
Cap to protect the male low pressure inflator connector from dirt and other muck. Print with TPU.
Simple holder for a Schrader (standard car tire valve) inflator that has a length of 1/4" pipe. Won't work if you have the quick disconnect directly attached to the inflator head. Print Settings Printer: Prusa MK3S Rafts: No Supports: No…
Male insert to protect low pressure inflator connector.
Real life problem. My hobby is scubadiving with dry suit from Scubapro. My inflator button fell off and I did find any replacement parts. Has an enhanced structure, compared to original. For best print quality place vertical, print solid…
Remix of the wall hook that I could use on my Skadis board. Sized the holes for the M2.5 SHCS, should be a min length of 14mm. I have two versions uploaded, 2 mount holes spaced at 80mm apart to skip a slot and 3 mount holes spaced at…
This is an insert for the Ryobi Power Inflator accessories holder spot that holds 2 shrader to presta valve adapters. I lost all the original tools, but 99% of my usage of this tool is inflating bike tires. I was constantly losing these…
Took a nice case and added an insert for the Kmart Australia ANKO branded Universal Inflator Kit: https://www.kmart.com.au/product/universal-inflator-kit-41772065/ Parts fit well, the lid has a press-fit option that works OK enough but it…
Gridfinity bin for the Ryobi USB Lithium High Volume Inflator (FVIF61K). 6 units by 3 units by 5 units tall in the standard Gridfinity system. No magnets because I think they're for suckers.
The one problem with the Einhell inflator is that there is no lock/safety for the rocker switch, so it can be turned on unwantedly (especially if kept in a car) unless the battery is removed. To save the hassle of this I created this…
Zip ties on to the clamp carriage of an EZ lift stand and holds your 3-in-1 inflator securely.
What These files can be used to magnetically carry your 16g CO2 cartridge and your Bontrager Air Rush Elite (or similarly sized low profile inline inflator) inside your RockShox Recon steer tube. Other forks with a 1.5" taper might work,…
2 piece bracket assembly that bolts to where a bottle cage would mount. Holds a Ryobi 4 volt inflator. Uses 2 5mm bolt, approve ¾ long. Make sure they are not too long as to prevent the seat post from moving up and down. Printed in PETG…
Description This is a remix of the Bike CO₂ Holder designed to improve compatibility and functionality. The original model was intended to fit alongside a standard bottle cage, but this version has been narrowed to work with mounts that…
The original part broke (photo in white color) We made some change regard to the original piece, we grow thicker the base and we add fillets in the helix to prevent break them It's recommendable 3D print it with heat resistant material…
