Counting matching models…
Feet for SSUPD's Meshroom S PC case. Improves ventilation and allows usage of standard (non-angled) DisplayPort cables. Uses existing holes in the case that are located below the rubber feet the case ships with. You have to remove those…
Uses 1 ADT-Link A7-A8Q HDMI 2.1 15cm Extension and 2 ADT-Link P7A-P8T-BL DisplayPort 1.4 15cm Extensions. Onshape Link
This are 25mm tall feet for the SSUPD Meshroom D. These are ~18mm taller than the original so your GPU can get more airflow for lower temperatures. Note: these do not fit the Meshroom S. Printed in PLA with a 0.6mm nozzle and 0.3mm layer…
This is a set of fan mounts for the SSUPD Meshroom D ITX PC case. The original case allows for the mounting of a 120mm or 140mm side exhaust fans using a series of rails. These rail span the entire width of the case and can interfere with…
Installing SFX power will allow you to move the front IO ports up to allow installation of longer graphics cards. m3 - Secure with bolts about 10 to 12 mm long and four M3 nuts. A 60mm exhaust fan can be added. You can also add a 2.5" SSD…
SSUPD Meshroom S V2 Noctua NF-A9 92mm top fan mount & GPU bracket I made for my SFF build, I believe this will only work for the Meshroom S V2, not the V1. Works perfectly with my EVGA 3080 FTW with the metal support GPU bracket mounted.…
SSUPD Meshroom S V2 rear GPU slot cover.
SSUPD Meshroom S V2 rear GPU mount & hdmi & display port adapter I made for my SFF build. This works perfectly with my EVGA 3080 FTW mounted in the highest position, It may interfere with longer graphics cards mounted in the lower…
This model allows mounting of the Iceman Cooler pump/reservoir combo onto the backside of the Ssupd Meshroom case. Unlike the ssupd marketing material, I chose to mount this onto the Horizontal PCI card slot by removing the existing…
Just recently I created this bracket per customer request. It was not very complicated however and only took an hour and a few test prints, so I might as well share it here. Feel free to use it for your own project, if you own a 3D…
Adds a lot more rigidity and makes me far more comfortable moving my meshroom around Slim fan can fit atop Onshape Link
SSUPD Meshroom S feets in 15, 20, 25, 45, 50, 55 and 60mm. Should also work well with NCase M2 and M3. Needed hardware (multiply by the number of feets) 1x M3x5x4 heatset 1x M3 bolt of 6, 8 or 10mm length (OPTIONAL) 1x M3 shim/washer,…
This is a turtle carved in stone. It was scanned with a phone (28 pictures) and then fed into MeshRoom. This program is really amazing. The original can be found here at the Spielplatz Pfarrlandplatz in Hannover, Germany…
Uses the adapter's panel mount screws to secure the bracket to the case. Will flex slightly when installing/removing, but stiff enough. Printed well with basic PLA, just had to slow down the first layer for all the details. F3D Archives…
There are holes for 4 different locations to place 3.5" drives in different configurations of the SSUPD Meshroom V2. The two upper locations are not mentioned in the manual. One of these upper locations cannot easily be used due to a…
I hated the bottom of my SSUPD Meshroom D case as well as the look of my GPU. I stripped the shroud off the GPU and designed this mod for the bottom of the case to replace the fans of GPU as well as provide more structure to the bottom of…
A simple and sturdy mount using existing holes in the SSUPD Meshroom S V2 to more securely hold an Asus 5090 Astral in the case. The PCIE extender is mounted but using lower mounting points, with the 10mm standoffs and is a slightly angle…
I recently water-cooled my PC in a meshroom V2 in a dual rad setup and even with slim fans on the side rad the clearance between the GPU blocks and the slim fans wasn't great, it was definitely enough for air to flow and move but the slim…
I was inspired by the above, however there were a few issues that I did not like with it: using screws through the vent holes, not making use of the 2 larger holes to the left of the port, and having to use the bottom right screw that is…
My first 'production' scan using : OpenScan Classic Arducam IMX519 Focus Stacking OpenScan3 beta Meshroom Photgrammetry Turntable flow FeatureExtraction: sift, dspsift, akaze Describer Density+Quality = ultra Meshing: Max Input Points +…
Meshroom S Case Feet Upgrade Kit – These feet raise your case by 20mm to optimize airflow and create space for HDMI/Display cables. Installation is easy using the Phillips head screws included with your case. The feet seamlessly integrate…
I fixed the size inaccuracies with the previous version by shortening the bottom piece by 1.651 mm and making the dove tails 1 mm wider for a better fit. Print with the pegs facing up. No supports.
Simple feet for pretty much any metal PC case. I wanted to put my Meshroom PC on its side but not completely kill the air flow. Magnets used are round 3mm thickness by 6mm diameter, held in with a touch of glue.
This is a front extension panel for the Meshroom S which uses the native case hardware (no clips needed). I used ASA to make sure it would survive the heat of the case, but other materials may be suitable. I found several options for…
(This is all also in the README) I commissioned prints for these models using PLA with 40% infill and they work like a charm. - You will need to print the Rear Panel if you want to use the parts in the MOBO and GPU folders. - The PSU…
This is a MESHROOM D foot that is higher than the original foot to improve air circulation and allows you to move the power button on the back to the front. There is a genuine power button type and a 12mm power button type.
Meshroom S Case Feet Upgrade Kit – These feet raise your case by 20mm to optimize airflow and create space for HDMI/Display cables. Installation is easy using the Phillips head screws included with your case. The feet seamlessly integrate…
