102 models
Buy here: https://3dreamforgebyaandn.etsy.com/uk/listing/1861948638/rc-mud-guard For maximum toughness use TPU however PLA works well too. BOM 2 x M3x20 Reuse the original M3x14 bolts to secure the shield to the towers.
Inner guard liners for the MJX 1/7 Citreon C3 Rally Car. UPDATES RE-TWEAKED FRONT GUARDS FOR NEW TYRE FROM ALIEXPRESS WHICH CAUSED RUBBING ON INNER WALLS ON FULL LOCK May look like an already available set on the market, but after seeing…
Rear shock tower for mjx hyper go print at 100% Infill, pla should be fine the holes for the upper suspension arm screws might need drilling out to 2.5mm after printing this was a requested part by @SamHammes_1124827 here on printables I…
Got a returned/broken RC car from a bin store. This is an MJX 1:16 scale Hyper Go buggy. The shocks tower (connects front shocks to frame) was broken. I printed a crude one from a not-to-be-mentioned printable model website, but wanted to…
Buy here: https://www.etsy.com/uk/listing/1876691283/mjx-hyper-go-10208-shock-lift This mod dramatically increases the droop and suspension range by moving the mounting point up 8-11mm. There is no drive shaft binding. ride height: front…
MJX 16230 Hyper Go Steering Cup for model h16bm Part number is 16230 As far as I can tell, it should work for both sides; if not, this one was designed for the right side (If you are looking at it from the back.) Just mirror it in your…
MJX Hyper Go 1/14 fan covers for H14 and 14209/14210 models
Made a shock tower for mjx hyper go after breaking my gfs and not being able to find a decent printable replacement should just bolt right on with no modification tho you might need to drill out the holes for the long pins for the upper…
Drift wheels and tire combined, its a very simple design, not made for looks, but to be functional, balanced and easy to print. Dimensions: Wheel+tire diameter - 70mm - smaller than the standard 80mm, for better throttle control and lower…
MJX 16207 Hyper Go RC Buggy Front Shock Tower Cover Needed Hardware: 2pcs M2.5x12mm screw (12mm would be perfect length, photo shows 20mm screws) 2pcs M2.5 nut
For MJX Hyper Go H16H H16E H16P 16207 16208 16209 16210 rc car. Part Numbers: Front swing up 16210 Front swing down 16220 Rear swing up 16240 Rear swing down 16250 Most of the measurements are the same, a bit redesigned to be more beefy,…
I broke front bumper on MJX Hyper Go 14301. This is the replacement part (part number 14101). It requires supports, but only for the part mounted to the chassis. If you are looking for bumper mount (part number 14102), please see: MJX…
Battery retention arm model can be found here: https://www.printables.com/model/645510-hyper-go-16207-16208-16209-16210-battery-arm Designed to snuggly fit a 75 * 34 * 26.5mm or 2.95 * 1.34 * 1.04inch battery pack This is the battery…
Dust cover for MJX 10208.
requested file by a user i dont have this rc car but it will fit the rear shocktower i made for the hyper go print at 100% with supports id recommend printing with a hard tpu or some sort of filament that can flex on an impact
Nylon: All suspension arms and bump Petg and others matterials: Battarey box andsteering arm
I have an MJX Hyper Go 16207. It is a wonderful cheap RC car and is too fast for its own good when used with the included 3S lipo battery. Fast enough to flip over often and damage the rear spoiler and the wheelie bar. In my case the…
I did the wheel nut for my MJX Hyper Go 14210. I printed with PLA and 5 perimeters, after some battery packs continues working perfect. Please let me know your feedback and if you test it with other model.
Some parts to improve scale looks of the car and also a bigger battery tray for the front that will be a direct replacement. Scale parts are the bonnet grills and a jerrycan. The 3mf file are correctly scaled as well as the grill .stl…
MJX Hyper Go 14301 front bumper mount. This is the replacement part (part number 14102). It requires supports.
MJX Hyper Go 14209 receiver box print with TPU, supports from build plate only
A battery plate, which fits nicely into the honeycomb pattern in the chassis of the MJX Hyper Go RC cars (tested in a MJX mjx hyper go 16210 brushless). I use velcro cable ties, which are fed through the middle of the plate. Both the…
Osłony zabezpieczające podczas upadku mojego autorstwa (pliki 1,2,3) Pliki 4,5 nie są moje , należy je szukać n stronie: https://makerworld.com/pl/models/990931-meijiaxin-h12y-spare-tire-side-panels?from=search#profileId-966410
For MJX Hyper Go H16H H16E H16P 16207 16208 16209 16210 rc car. PN 16100 Redesigned version to better protect from crashes and to replace. its usually a weak point under the front bumber, and i guess it will break at some point. The…
Custom spoiler for the popular RC Buggy MJX HyperGo 16207 wich also protects the shocks tower Print it with PETG or PCTG, the bracket/mount can be printed with TPU to prevent breakage in the event of a harder collision. Use 7% organic…
Custom-designed strengthened front shock tower for MJX Hyper Go 1/16 scale models. This part is a direct replacement for the stock component and is engineered to fit precisely using the original hardware. Printed in solid with 100% infill…
This model was designed specifically for TPU plastic. It molds perfectly to the shape of the body and breaks slowly. Everything is installed in its original place. The cover is slightly larger than the original one, which better protects…
The Boards you need are from daver18qc, you need them scale up to a lenght of 160mm. https://www.printables.com/model/9497-110-scale-maxtrax-mkii-traction-board the holder for the spare tire is with 12,5mm offset to the right side
Taken from here: https://www.thingiverse.com/thing:5674578 For 16208 and 16209
I had this piece break on my kid's MJX Hyper Go RC car so I designed a new peace please note it took me 6 iterations to get it to fit just right. Also, it will need a little bit of support. I have oriented the STL in the correct…
this my first-ever design this part fits on 1/16 and 1/14 scale MJX cars Print Settings Printer brand: AnkerMake Printer: AnkerMake M5 Supports: Yes Resolution: .12 Infill: 80 Filament brand: crealty Filament color: black Filament…
I designed these hooks specifically for my MJX HYPER GO RX car. I printed them with eSun PETG-CF filament, using 100% infill, concentric patterns, and a low, constant speed (I used 50mm/s for all printing fields, 255°C/70°C). For the best…
A mounting bracket to install an AGF-RC B13DLM Servo into your MJX Hyper Go RC car
Replace the stock upper links with turnbuckles and dial in the rear camber on the MJX Hyper Go 14301 to tweak the handling. May require running larger diameter wheels (check my other models) to clear the parts. Hardware 2x M3x16…
Assembled with 2 bolts 2.5 mm by 20 mm
When i saw Simon Vezina's awesome Omni Terminator rollcage, i decided to design and fit one to my 3d print test car, the MJX H16BM. It does not fit on the body but is just an open roll cage. You are able to attach the stock roof skids and…
Since I broke the original spoiler bracket, I decided to design and make my own. With the original one the spoiler practically touched the shock tower, which I didn't like, so I designed this one in such a way that the spoiler is moved…
Drift sleeve for 16207 buggy. Works well. Print with PETG.
Right and Left doors Hyper Go H12Y JEEP
Don't worry about the look of the body and the wheels, Its been to the skatepark over 30 times on 3s. One file works for both left and right. new file added! has a retainer that fits on to the outer edge to keep the paddles from sliding…
Front body mount for MJX Hyper Go 14210 or H14BM. This part it's not an exact copy from the original piece because it was designed to be printed instead of injection molding and the material it's also different. Print: 0.2mm layer height;…
This is the front bumper assembly for the RC buggy MJX Hyper Go 16207 The bumper is made with TPU 95A, the mount/bracket with PETG, but you can made it also with PCTG or also harder TPU. I ordered a spool of 72D TPU to test and will made…
This wheel accepts Tamiya Mini Cooper M-Chassis 60D tires and allows you to run them on the MJX Hyper Go 14301. This gives a few more tire options for the car as well as some extra clearance if you want to add adjustable upper control…
This is a bigger version of the original receiver box top part for a MJX Hyper Go 14210, 14209 or H14BM (only tested with 14210). It has the "max" size, that's fits, without modify the shell mounting height etc..
The goal was to keep the original placement of the receiver box and provides an addition 10mm clearance for the larger 4274 motor. BOM m3x20 2 m3x30 2 5x3mm foam m3 inserts 6 Print Support: Yes Material: PLA
Allows you to use bigger batterys and fix the battery cables Thanks to @RabidBadger_397944 for the first design.
I had to add a cylinder so that the bearings sitting surface would be smaller. Small mods from the original, but they actually make the model usable. I used it for MJX Hyper GO 16208 Its tested ad it works. i dont know how durable will…
The circular plate that the spring braces on at the bottom of the shock. What do you call this thing? Printed with PLA+ and will likely hold up fine but you're prolly better off with PETG
MJX Hyper Go 14210 / H14BM wheelie bar How to print: Perimeters: 4 Supports: No Seam position: Random Notes: The wheel doesn't work in PLA, print in TPU. The solid wheel didn't test it yet. The pin it's working in PLA but probably it's…
Its a replacement wheel design for stock wheels, designed from scratch but inspired from stock wheel
Replacement for the front suspension guard for your shock eye. PETG or TPU reccomended If not lost you can use the replaced screw of the wheely bar ;-) Dont use the same hole like the screw from the front.
Wide version it's to use with original wheel size but I couldn't do a version that doesn't break with PLA, PETG or PA. Narrow version it's using smaller wheels to stress less the pin and works much better for me. Best result with pin I…
Fix the batteries to this base using elastic bands or cable ties. It fits the popular batteries: HOOVO 3S Lipo Battery 2200 mAh Ovonic Air S Lipo Battery 2200 mAh This is a redesign of @ByteChild_506695 battery plate, without the need for…
The model is designed to hold the battery in place. The front part is designed to prevent damage to the battery in the event of an accident with the RC car. When installing this holder, you need to remove the original holder. Mount the…
Buggy style RC body designed specifically for MJX 14211, with perfect compatibility and effective air intake tunnel to cool the motor. To get the best durability, please print it with TPU, and it will be nearly unbreakable. Print the…
In addition to a new look, the doors will also protect the model from scratches. It's best to use PLA filament.
This is a insert for the battery holder, to have a flat surface for Velcro tape (if you don't want to use the original straps). If you don't want to disassemble the whole car, you need to cut few mm from every side of the cross to fit.…
Cap & antenna-mod mount for the MJX Bugs 3 transmitter. Replaces the stock cap/fake antenna nub that comes with the transmitter. Files include STEP versions for easier CAD editing. If you make one, let me know how it turns out! Types: cap…
MJX Hyper Go 1/14 Scale Turnbuckle Spacer These units always seem to come with the toe angle off and needing adjustment out of the box. Adding this spacer will allow you to tighten the turnbuckle down. You can manually chop off z height…
I remixed another bumper design to better fit the MJX 16207 Buggy. I printed it in 95A TPU on the creality K1 Max. No supports. I made the backmost 48 mm solid, used 25 walls or something like that. The frontmost 13 mm is printed with 2…
mjx hyper go 16208 and same front dumper part - 16101
I tried to refill the shocks for my MJX Hyper Go 16208, but 70 wt silicone oil was still too thin for them. so i printed the shock pistons to be able to remake the holes or just control the dampening from the diameter of the piston. The…
MJX 14210 shock connector, I used Flex TPU - 64D Filament. I suggest it for its flex to strength ratio
In addition to a new look, the doors will also protect the model from scratches. It's best to use PLA filament.
This is a prop guard for mjx bugs 3 mini/eachine ex2 mini. Its flat not like the original, but its easier to print this form, and I think it works. Print Settings Printer: prusa i3 rework 1.5 reworked by hygy Supports: No Resolution: 0.16…
This is a drift ring designed specifically for the MJX Hypergo 1430x 1:14 scale stock tires. It allows you to easily convert your RC car for drifting and gets you cheap replacements. Installation & Fit Snug Fit: This ring is designed to…
Little camera stabilizer in delta format you use the original camera frame... you only replace the upper part of camera holder on mjx bugs b3h and eachine ex2h the file gimbal mjx bug b3 pt2 need a support when you print i used 20% infill…
A low profile durable wing mount, ideal for street bashing
My son's MJX car's remote control got malfunction, the steering wheel could not centered. So I opened the remote crontrol and recognized the broken part and recreated a strengthened part. Fits for MJX remote control Hypergo H12Y . Printed…
The rear wing on the MJX 16212 might not do much for aerodynamics, but it definitely protects the body shell in a crash. Mine snapped after just a few bad landings. I created an easy to print flexible version. Made of TPU it will adapt to…
Fan mount 1:7 scale 7304 should work for the others to as long its 1;7 Scale. Mounting hole in chassi and the fan mount needs to be drilled or if you use any strong duble sides tape should work to
MJX Hyper Go 14210 / H14BM wheelie bar How to print: Perimeters: 4 Supports: No Seam position: Random Notes: The wheel doesn't work in PLA, print in TPU. The solid wheel didn't test it yet. The pin it's working in PLA but probably it's…
Custom-designed strengthened front shock tower for MJX Hyper Go 1/16 scale models. This part is a direct replacement for the stock component and is engineered to fit precisely using the original hardware. Printed in solid with 100% infill…
MJX 14210 shock connector, I used Flex TPU - 64D Filament. I suggest it for its flex to strength ratio
In addition to a new look, the doors will also protect the model from scratches. It's best to use PLA filament.
In addition to a new look, the doors will also protect the model from scratches. It's best to use PLA filament.
The model is designed to hold the battery in place. The front part is designed to prevent damage to the battery in the event of an accident with the RC car. When installing this holder, you need to remove the original holder. Mount the…
MJX Hyper Go 14209 receiver box print with TPU, supports from build plate only
Fix the batteries to this base using elastic bands or cable ties. It fits the popular batteries: HOOVO 3S Lipo Battery 2200 mAh Ovonic Air S Lipo Battery 2200 mAh This is a redesign of @ByteChild_506695 battery plate, without the need for…
This model was designed specifically for TPU plastic. It molds perfectly to the shape of the body and breaks slowly. Everything is installed in its original place. The cover is slightly larger than the original one, which better protects…
Buy here: https://www.etsy.com/uk/listing/1876689877/mjx-10208-bumper-pad-ring The pads / rings provides similar resistance to the original but lasts longer. Material: TPU 95A
One of the cars was a bit too noisy, clearly a gear mesh issue, so i redesigned the motor guard and played with offsets and tolerances to get a perfect gear mesh. This is the only way to mesh the gears of the Hyper Go cars, as the motor…
Easy to print front Action Cam mount for MJX bugs 6. Replaces front grill, reuses screws which fixed front grill. Cam is fixed which M6 screw. Cam can be tilted by moving back and forth. Printed fine on my Anet A8 without supports. Print…
MJX body front body clip, can use default quick attach body with this model
This is a replacement front shock tower for the MJX HyperGo 20208 RC truck. It is much beefier than the stock one, so even in PLA it should be a big improvement, but I recommend printing it in TPU (the stiffer the better, I used 95A) and…
This is a 2 - 3 mm servo saver spacer which compresses the spring more. To reassemble the the servo saver use the provided tool.
Tisk položené do “A” a doporučím trochu seříznout spodní části pro lepší styčnou plochu.
Witam Jest to "chyba" ostateczna wersja modelu dachu dla MJX Hyper Go H12Y. W pierwszej wersji model zaprojektowałem jako jedno częściowy wydruk, lecz ścianki które się drukowały pionowo nie miały dostatecznej wytrzymałości i dlatego…
MJX H12Y 1:12 RC roof rack with added side rails. Based on the original rack design. https://makerworld.com/zh/models/2257558-hyper-go-h12y-upgrade?from=search#profileId-2459355 Rail diameter: 3mm. Due to the 1.3° slope on the bottom…
GoPro camera mount for H12Y MJX. Hardtop mount. DEMO:
My version of leg for MJX Bugs 6. Printed with TPU. Category: Replacement Parts
Smaller and lighter version of battery holder. Suits original packet (1.3Ah, 7.4V) but without case.. Category: Replacement Parts
MJX Transmitter GR-246 replacement stick, very easy to loose. May need to sand the base to fit. Category: R/C Vehicles
