Counting matching models…
Just after I made the GoPro-mount for my TP-Link TL-WR902 travel router , I decided to upgrade to the Beryl AX. As I use a GoPro-mount for mounting the router at a certain occasion, I had to make a suitable clip for the new router. I…
Print with 0.1mm layer height for the best snap fit. No supports needed.
This is a mounting bracket for a GL.iNet Beryl AX Wifi 6 GL-MT3000 travel router . I needed a robust mounting bracket for this travel router to mount in our RV. I plan to merge this mount into a larger mounting bracket to hold a POE…
Re design to allow the use of the USB type C popular MT3608 that you can buy at Aliexpress or Amazon for less than 1 buck. You have 2 top cap versions, one with vents (if your project will need some power) or full covered to protect from…
As most people are coming to realize, the MT3 keycap profile for mechanical keyboard keycaps is the best :-) The profile designer, Matt3o has released high quality STL files for 1u R0, and 6.25u spacebar at…
This is a vase mode print I designed to hold 2 18650 cells as well as a TP4056 charge/protection circuit & MT3608 DC-DC boost circuit. Here's the link to where I bought the circuits from. https://a.aliexpress.com/_mNJGjrV 0.2mm layer…
Case for MT3608 Step-Up Boost Converter Module. Cable strain relief integrated (only if the cable is not too thin). The potentiometer is accessible from the outside. Has cooling vents. Print Settings Printer: Wanhao Duplicator i3 V2…
These are simple holders for MT2 and MT3 tools. Both models use #8 screws to mount to a workbench or piece of wood. STEP files are included. These are based off of this original design by CABTinker on thingiverse. I've added the missing…
Introducing the GL-MT3000 Socket Mount! This meticulously designed printable allows you to securely mount your GL-MT3000 router without the need for complicated installations or additional hardware. Crafted with precision and ease-of-use…
This is a mt32-pi case for the Raspberry Pi Zero 2 W and the mt32-pi hat sold by Yavimaya. The design includes 2 case pieces (front and back), a 11 mm spacer and 1 button. You will need to print off 2 buttons and 2 spacers. I have also…
Mount your converter with screws. Hole sized for 23 mm screws. Use supports under the clip parts. When unscrewed should flex enough even with PLA to get the board in and after screwing in should hold it tight. STEP file included.
It's a remix from https://www.thingiverse.com/thing:3370199 This is a simple snap case print to keep you from burning your fingers on the hot choke coil of the MT3608 voltage boost module. - No additional screws required! - Please note…
Morse Taper 3 (MK3/MT3) x 2 drill bit holder. The tool holder has a 8° angle, which makes it easy to reach the tooling. Print standing with 10% gyroid/grid infill and grid support from build plate only. The tool holder module couples with…
Morse Taper 3 (MK3/MT3) x 1 drill bit/tool holder. The tool holder has a 8° angle, which makes it easy to reach the tooling. Print standing with 10% gyroid/grid infill and grid support from base plate only. The tool holder module couples…
I suggest you print in PETG with 0.2mm layers. Print-in-place model. No supports needed. Fasten strain relief for cable with M3 screws directly into the printed holes. 2023-12-03 Version with cable strain relief on both sides added. For…
You need 4 x 12mm m4 screws, the original ones are not long enough. Sand the surface with very fine grain paper.
This is a case for the 2A Micro USB boost converters found all over AliExpress . The chip used is an MT3608 but the chip is marked as "B6286 (K)" I use mine to test my 12v projects from a 5v USB powerbank instead of firing up the bench…
Remixed the base to include flat head screw mount tabs. the hole is 4mm. The tapered area diameter is 8mm.
This is a lightweight case I created to safely carry the GL.iNet Beryl AX (GL-MT3000) router in my luggage. It only weighs 21 grams and is printed in vase mode. (The router weighs 198g without any accessories.) Printing Print 1 body + 1…
This 2u POS Keycap is generated from the script provided in the Model this is remixed from. It's in R4 spacebar profile(rounded top rather than dish). I uploaded this as a Remix to make it a bit easier to find if looking specifically for…
I made this case to create something tidy for my wall mount of Tenda P200 powerline and glinet router to extend my wifi at home. Maybe useful also for you. My advice is to paste with vinyl glue the two pieces to avoid support on printing.…
Halter mit großen Standfuß für mini Router von GL iNet. Wurde entworfen für den Einsatz mit einem LTE Stick.
This is a casing for the MT3608 DC-DC Boost converter which can be used in various applications. I use it to create a usb power box like PV-Productions sell to power my lego motors over usb, since my PV-Productions one broke. You can…
Many small lathes (such as my 9x20 lathe) have an internal Morse MT3 taper in the head-stock spindle. When using a center in this MT3 socket, it is very important that the socket is very clean to ensure maximum precision. This simple…
I designed this in Alibre CAD to fit my 3034-lite T-slot rail toolholder rack. The holes are spaced for 5/16-18 screws. For best results, use a raft with plenty of supports. Updated on 9/17/22 to remove downward facing fillets and replace…
Print settings: 0,2mm PETG 15% Infill No Brim CAD File:…
A holder for a MT3 dead centre, can be used other MT3 things. There are 3 versions, 1 has the text MT3 on it, 1 has no text, so you can use a label printer and stick on the description, an 1 has no text and no holes on the back, to allow…
This stand holds and displays my new set of cheap Collets for Morse Taper Number 3. This collet set arrived in oily bags packed in cardboard boxes so this was my solution. I will likely print the plain version also just to store other MT3…
Modulo de caja para MT3608 que puede ser adquirido aqui: https://es.aliexpress.com/item/1005006102572363.html Instrucciones de armado: Se deben imprimir todas las piezas especificadas, el archivo bajo la etiqueta (support) no es…
This model holds MT3 taper stuff on the wall. Requires 4x #8 screws. Fits items up to 2.5" in diameter.
Remix by Jan‑ E.de (@JanEde) -> https://www.printables.com/de/model/631877-mounting-clip-for-travel-router-beryl-ax-with-wall I removed the screw holes and added a flat surface so the mount can be attached with tape instead of screws.…
This internal frame to hold in place the MT3608 Voltage Regulator and a TP4056 Battery Charger along with a 3.7v 500mAh Lithium Battery inside the DSO150, is designed to fulfill my upgrade needs and I hope is useful to someone else, the…
This model allows you to mount a micro USB to MT3608 adjustable power supply such as this one: MT3608 Adjustable Step Up Module Voltage Regulator Micro USB Type-c 2V-24V to 5V-28V 2A Step-Up DC-DC Boost Converter . I didn't provide any…
I messed up dimensions. Scale down to 10%
Grommet with ID tapered to accommodate/hold a Morse taper #3 (MT3) center. Sized to snap into in 1.25" diameter hole drilled in ¼" flat stock. Print in TPU and adjust fill to achieve desired flexibility/softness.
When you need to power your creation from USB 5V but it needs 12V or another voltage higher than 5, you usually resort to using the common MT3608 boost converter. This is usually bought in the form of an assembled PCB and can be bought…
Tolerances are tight. If the board does not fit, print the parts with 100,5% oder 101% scale. Use 8 M1,4x5mmm self tapping screws for mounting the board and lid. Use a M3x40mm screw for the USB brace.
Printed Parts Required to Complete Assembly: (1) "mt32_frontmod" (1) "mt32_back" (2) "mt32_buttonmod" (2) "mt32_spacer" (1) "mt32_stand" (Optional) IMPORTANT NOTE! - #1 - These models are intended for resin printing only, FDM or other…
Like it says, I needed shorter legs to fit on a small shelf, and put some nice round padd feet on them. Figured while I was at it I'd do a couple variations; Added screw holes, or pockets for hot glue or other adhesive, and pockets for…
This is a little micro power supply, there can be used for quick test of small devices. It is running on 2 AA battery, so don't expect lots of power. It use a MT3608 and will be able to give from about 3vdc to 24vdc in output. Category:…
Mon ventilateur Noctua 12v ne démarrait pas toujours tout seul en 5v. J'ai donc rajouter un petit booster MT3608 réglé à 7v au couvercle. Cela fait un tout petit peu plus de bruit mais j'ai gagné 5°C :-) PS : Il vaut mieux faire les…
This case accommodates the LM2596 Buck Converter and the MT3608* Boost Converter. Screw holes are M2 (7mm length suggested)-8 required. Route line-in wires ( "VIN+ and VIN-" to the converters through the holes on the lower-rear of each…
USB-корпус для підвищувального модуля постійного струму MT3608
A Case for the MT32PiZ2W. 4x M3x20 sockethead-screws 4x M3 square nut Link to the MT32PiZ2W-Project: https://misterfpga.org/viewtopic.php?p=40581#p40581
This simple holder snugly holds my MT32-Pi Hat and a PiA3+ ( in Geekworm Aluminium case ) It can stand alone or can be sat atop this Tapto Card Reader Print at whatever resolution you want , though i reccommend at least 0.2mm for a smooth…
This is an enclosure for an MT32 Pi using a Pi Zero 2W and the MT32 Pi Hat sold by Yavimaya Maker at: https://www.tindie.com/products/taviens/mt32pi-hat-for-zero-2w-model-raspberry-pi/ It uses 4x M2.5 20mm countersunk screws to attach the…
--- English --- Housing for the MT300N (Mango) and one of these chinese PoE splitters. Thus the devices have a significantly higher WAF. --- Deutsch --- Ein Gehäuse für den MT300N (Mango) von GL.Inet und einen der chinesischen…
Tool holder insert MT3 (Morse Taper 3) This is a printable insert for 35mm (1-3/8") square mild steel tubing. When it comes to heavy tools, a tool holder made of steel is a great option. I've made this insert so that You can click into…
I love Retro Frog's Mister Cases, but they were a little too thick to allow the mt32-pi lite to get a good connection (without sitting at a weird angle). I cut a space out for the add-on board so that it sits flush against the side of the…
a simple stand for the Sony SA-MT300 soundbar to better fit om a desk above a keyboard. I can be printed with only 2-3 walls, 15% gyroid infill I would advise a 5 mm brim just to be sure v2 added with small improvement in design
This is an enclosure for an MT32 Pi using a Pi Zero 2W and the MT32 Pi Hat sold by Yavimaya Maker at: https://www.tindie.com/products/taviens/mt32pi-hat-for-zero-2w-model-raspberry-pi/ It's based on the one they created, but it has a…
I printed this in PLA+.. Tip: Check the dimensions in your slicers measuring tool before printing to make sure you will get what you expect.
Wave Rover mount for gli-net MT3000 router
These are 99.9% accurate row-5 MT3 spacebars. I'm the designer of the MT3 keycap profile, so you could say these are official :) You can read more about this on my blog: https://matt3o.com/mt3-row-5-spacebar-stls-all-of-them/
Mt32-pi mini front case for Raspberry Pi Zero 2W and the mt32-pi hat sold by GamingFun80pt 📋 Remix Notice / Required Parts This upload contains only the modified Front Case redesigned to fit 0.91" and 0.96" OLED screens. ⚠ Important Note:…
This is an enclosure for an MT32 Pi using a Pi Zero 2W and the MT32 Pi Hat sold by Yavimaya Maker at: https://www.tindie.com/products/taviens/mt32pi-hat-for-zero-2w-model-raspberry-pi/ It's based on the one they created, but it has a…
Gridfinity stand for MT3 (Morse 3) tool collets. OnShape model: https://cad.onshape.com/documents/05ab2237f1d2d6fd799cb4c8/w/590c26fd9ab07364262765d6/e/a9f376829f4b79f735146607
--- English --- Housing for the MT300N (Mango) and one of these chinese PoE splitters. Thus the devices have a significantly higher WAF. --- Deutsch --- Ein Gehäuse für den MT300N (Mango) von GL.Inet und einen der chinesischen…
I printed this in PLA+.. Tip: Check the dimensions in your slicers measuring tool before printing to make sure you will get what you expect.
Tolerances are tight. If the board does not fit, print the parts with 100,5% oder 101% scale. Use 8 M1,4x5mmm self tapping screws for mounting the board and lid. Use a M3x40mm screw for the USB brace.
Case for MT3608 Step-Up Boost Converter Module. Cable strain relief integrated (only if the cable is not too thin). The potentiometer is accessible from the outside. Has cooling vents. Print Settings Printer: Wanhao Duplicator i3 V2…
Just after I made the GoPro-mount for my TP-Link TL-WR902 travel router , I decided to upgrade to the Beryl AX. As I use a GoPro-mount for mounting the router at a certain occasion, I had to make a suitable clip for the new router. I…
gridfinity with magnet holes, holder for MT3 dead center
Gridfinity stand for MT3 (Morse 3) tool collets. OnShape model: https://cad.onshape.com/documents/05ab2237f1d2d6fd799cb4c8/w/590c26fd9ab07364262765d6/e/a9f376829f4b79f735146607
1-10PCS MT3608 DC-DC Step Up Converter Booster Netzteil Modul Boost Step-up Board MAX ausgang 28V 2A - AliExpress 502
The 3x3 variant works on most printers, 25% gyroid infill works well. Complete overkill cause I have some pretty heavy collets a lot bigger than the normal ER collet chucks. Made mine out of PETG but PLA is probably more stiff Will upload…
I love Retro Frog's Mister Cases, but they were a little too thick to allow the mt32-pi lite to get a good connection (without sitting at a weird angle). I cut a space out for the add-on board so that it sits flush against the side of the…
1x1 gridfinity grid and 4 height units. Fits 6 MT3608 DC/DC converters
I wanted to power a Raspberry Pi from this UPS and find out that the output voltage was only 4,9 V. So I had to add a booster module (MT3618) to get 5.1 V. I added a switch and an output connector (dual USB A/C) Printed in PLA Additional…
--- This is a compact 3D-printed enclosure designed to house the internal power supply and audio components for a DIY Bluetooth device — such as a portable speaker. The case integrates a Li‑ion battery with a TP4056 charging module, an…
The official case for mt32-pi | zero . The TOP half should be flipped upside-down before printing. Print with supports (print bed only). In other words, there should only be supports below the PCB mounting holes. Support settings from…
The official desk stand for mt32-pi | zero . No supports required. Recessed holes on the bottom for adding rubber feet (e.g. https://www.aliexpress.com/item/1005002035433332.html ).
Simple case for the mt3608 boost converter. It has places to insert 4mmx1.5mm neodymium magnets.
This is a MT3 collet rack. It was designed with 1.5" screw spacing to attach to 80/20 brand 3034-lite rail. The model should import in the correct orientation and has been optimized to give best results printed in this orientation. Your…
You can buy this there: https://www.tindie.com/stores/taviens/ 2 versions: rounded and chamfered. Mounting: 4 x M2.5 12mm spacers 8 x M2.5 8mm screws Print Settings Printer: Artillery Genius Rafts: Doesn't Matter Supports: Yes Resolution:…
I bought a sack of 50 DC:DC step-up supplies from AliExpress for $20.69 (USD). Being in a sack, I can't readily identify what they are, since I also got 20 step-down buck converters and 10 humidity/temperature sensors. I needed a compact…
This is a button plunger for the mt32-pi MiSTer HAT that extends the tactile buttons from the circuit board to the top plate. Designed for use with 8mm standoffs only. Category: Electronics
This is a "shim" piece for the mt32-pi MiSTer HAT that goes between the circuit board and the top plate to cover the open edges of the stacked boards. Designed for use with 8mm standoffs and the right-hand-side USB port only. See photo…
This is the Multisystem cartridge enclosure for the PiMMS (MT32Pi) expansion PCB - requires the use of a Raspberry Pi Zero 2/2W You can buy a cartridge here - Pi-MMS Expansion Cartridge for Multisystem (No RPi, Assembled) (heber.co.uk)…
Hello, I closed the usb port opening. I made the case longer.
se ensambla por presión y encaja muy bien, impreso en PLA al 25%
Angle bracket for Sony HT-MT301 soundbar to orient the soundbar to toward the user. Bonus, it allows the cable to go under the soundbar like the one for my keyboard. It should work fine with all soundbar with a 10 cm x 5 cm side section.…
