Counting matching models…
[3 Dec 2025] – Second Version V2.1 - Heltec V4-compatible cases added This H1+ case is a remix of the original H1 case design by muzi.works and reworked to, as the ‘ + ’ in the name suggests, accommodate a further enhanced Heltec V3/V4…
UPDATE: I took out the lump because it wasn't really needed and gets in the way of most lanyards and some mods. Added a version that works with M2.5 nuts for the Baofeng clip. I based it on the style of the holsters for my Alley Chat HT…
Original model for the Heltec V3 by Muziworks: https://www.printables.com/model/741974-h1-case-for-heltec-v3-running-meshtastic This is a modified version of the original H1 case by Muziworks. I wanted to play around with a Heltec V4…
I based it on the style of the holsters for my Alley Chat HT Pocket, and I think it goes really well with the H2T design. Baofeng Belt Clip Generic Belt Clip Heat Set Inserts This is a new work completely owned by myself, but I am…
See changelog to see all the updates and changes I did. __________________________________________________________________________ Original Muzi text for his Original H1: Case for the Heltec V3 Lora board. Recommended to print in a Matte…
The remix by @tehspiah works great with Heltecv4. As I'm using the official GPS, I needed to fit the GPS in so I added a little cavity in the TOP part.
Filament indicator leds and slightly bigger holes
IMPORTANT, read the assembly instructions, DON'T tape the OLED screen to the base or OLED-bracket yet! This is a case/enclosure for the Base Uno/Duo and the Super IO expansion board from muzi ᴡᴏʀᴋꜱ. The case features a sliding on/off…
This is a charging cradle for the muzi.works H1 for the Heltec V3. It allows the device to stand upright while charging or while it is hooked up to a computer. It uses these (amazon) right angle USB C connectors which fit inside the…
Clip to hold a Heltec V3 in the MuziWorks case, named "H1 - Case for Heltec V3 running Meshtastic" on printables. Can be used to mount it on the wrist or anywhere else. There is a cut for the belt/strap up to 24mm x 2.4mm. The strap can…
Unscrew the nut and washer on the SMA connector. put the radio into the case, close the lid and tighten the washer/nut back on. There are two LID variations, 1 with a usr btn whole and one without.
I printed the upper and lower part in ABS and the Buttons in PLA. The Buttons are a little tricky to print, i used a 0.2mm nozzle and a layer height of 0.08mm. Hardware required: 5x M2x4mm Brass inserts 4x M2x12mm countersunk screw 1x…
A little desktop stand for the popular H2T case by muzi.works for the Heltect T114. I printed it with 3 walls and 5% infill using PETG.
Buttons that worked better for me than the original buttons designed for this case. These are designed to work with PLA or similarly stiff filaments.
This is a first draft of the radio handset designed to house the Muzi Works Base Duo and Super IO boards along with their Base Battery and whip antenna. I encountered no fitment issues, but please let me know if any are encountered so I…
Threw together a quick case for the Muzi Base Duo/Uno that supports the BB15 battery. There's no provision for the 2.4 ghz LoRa antenna: don't enable it. It might blow the 2.4 ghz section of the chip. I don't know. Uses M2 screws to hold…
I originally modified this Multiboard Holster for my personal muzi.works H1 Heltec V3 setup to make charging my Heltec V3 more convenient.
Remix of H2T 103665 battery model to fit the makerfocus 3000mah battery
Design to allow for slop. Radio easily slides in and out without any binding. Radio can be placed in either direction. Example is printed with PLA with 5% infill at 0.25mm. There is enough held at the bottom that the radio will stay…
Uses 3x M2x20 Screws, and 3 M2x2x3.2 heat set inserts
This is an update to the radio handset designed to house the Muzi Works Base Uno/Duo and Super IO boards along with their Base Battery and whip antenna. I retained the single-screw access through the back of the enclosure to the battery…
This back plate fit with the Muzi Works BB15 BASE System Battery, but I did have to nudge it higher onto the board a bit. If space is a concern, I've uploaded a 2x inserts version that should let the battery stay exactly the same as the…
Deeper back side of the case by Nikolai Schauer for larger batteries.
The MUZI WORKS H1 Heltec V3 Vertical stand is a custom-designed enclosure and mounting solution built specifically for this case. Engineered with both functionality and aesthetics in mind, this vertical setup optimizes space usage while…
This is an enlarged version of Alley Cat's Pager Style Holster for the muzi.works H1 Heltec V3 Case It is meant to be used with a Baofeng belt clip https://amzn.to/4mwXDDb I will be applying double sided tape and mounting it onto my car…
These are the magnetic charging cables that I used for this. In testing, printing at .3mm layer height produced a good friction fit. When I printed at my normal .2mm layer height, the cables didn't stay put, but that was fixed with a bit…
As of yet, I was unable to find a case for the Super IO by Muzi, so I decided to set out and make one myself. I used the CAD file provided on the website for the board and modeled a case using Shap3rd. This is what I came up with. Fully…
Mounts are designed specifically to hold the Heltec H1 or H1+ case. It has a space so you can plug in a USB-C cable.
Stand works with the H1+ case and is meant for Horizontal storage and charging. I would recommend printing with support for 65 degree plus. This helps support the rounded underside. Standard Infill and walls. V2.2 might be a little to…
I originally modified this Multiboard Holster for my personal muzi.works H1 Heltec V3 setup to make charging my Heltec V3 more convenient.
These are the magnetic charging cables that I used for this. In testing, printing at .3mm layer height produced a good friction fit. When I printed at my normal .2mm layer height, the cables didn't stay put, but that was fixed with a bit…
I printed the upper and lower part in ABS and the Buttons in PLA. The Buttons are a little tricky to print, i used a 0.2mm nozzle and a layer height of 0.08mm. Hardware required: 5x M2x4mm Brass inserts 4x M2x12mm countersunk screw 1x…
This is a first draft of the radio handset designed to house the Muzi Works Base Duo and Super IO boards along with their Base Battery and whip antenna. I encountered no fitment issues, but please let me know if any are encountered so I…
As of yet, I was unable to find a case for the Super IO by Muzi, so I decided to set out and make one myself. I used the CAD file provided on the website for the board and modeled a case using Shap3rd. This is what I came up with. Fully…
Deeper back side of the case by Nikolai Schauer for larger batteries.
See changelog to see all the updates and changes I did. __________________________________________________________________________ Original Muzi text for his Original H1: Case for the Heltec V3 Lora board. Recommended to print in a Matte…
change ball to 5.5mm, and modified to easy install and repair
