Counting matching models…
Materials Screws 8x Original screws from feet 8-14x M3 x 6mm 2-4x per Support Bar to Side Rail I use 2 per bar, but there are holes for 4 1x per Rear Side Plate to Side Rail 14-22x M3 x 8mm 4-12x Side Rail to Disk Drive 3x per Front Side…
I have a 4090 horizontally mounted in my NR200 Mini-ITX case and needed to drill out more ventilation holes in the steel sheet metal side panels. This drill jig will slot into existing holes so you can line up the precise pilot holes for…
EDIT: v2: better support for mounting hard drive with top facing right. Most SATA angle cables are only down, so mounting the hard drive on it's right side/clockwise will allow use of these cables. This is a remake of the official Cooler…
My Framework Desktop Mainboard was hitting 100 C during inference while using the stock fan duct, which is obviously a problem. Not only does this replacement duct provide greater airflow to the 120 mm cooling fan, it extends to the side…
I made this cover to tie everything together in my build. And it hides the wires around the PSU. The RGB strips are Phanteks Neon strips and they must be cut to length. The 55cm one (M5) should reach all the way around but I suggest you…
Was looking to add better airflow by adding some fans in the bottom inside, but restricted for space because I am getting a triple slot GPU in the near future. So I got the idea to add slim 120x17mm fans to the outside and move the dust…
Yet another HDD Mount for the NR200. This version allows you to have both a top slim fan and a full length GPU. this one also has extra space between the model and the adapter to allow better air flow. I've used Noctua's a12x15 as a top…
"A mount to allow an ATX PSU to be used in the NR200P case. This holds the power supply at the front of the case in front of the graphics card with space to allow the front panel IO cables through. It's based on the one you can download…
Compatible with Corsair 280mm AIO Printed in PETG 20% infill I used someone else's left side though I may redo it if I have time.
A simple way to store your headphone on the cooler master nr200p case
remix of controller holder with the hooks extended to each side with a cut in the centre.
These are the .stl files I made two years ago to build a custom water cooling loop into my current PC. For those of you familiar with the Cooler Master NR200 case, you'll know it is a nice mini-ITX case and it gives you quite much…
Adapter to use a 240mm Water Cooler on the top panel and keeping the fans in their original position. I couldn't find any adapter that would keep all the original case parts and still close the glass panel. With this adapter, I moved the…
In NR200P v2 case by default you can use sfx and sfx-l standards power supply. As you could imagine going in smaller dimensions standards is quite a bit more expensive than standard atx. However the amount of space in the case itself is…
Wanted a bit more airflow for my NR200p dual rad water-cooled setup so cut out some of the excess behind the front panel and replaced it with this. Its a big model, just about filled the bed on my Voron 2.4's 30cm build plate. Needs 8 M3…
I remixed Trajan s “ Honeycomb Wall PS5 DualSense and DualSense Edge Controller Mount ” to a mount that could hold the controller at the side of a NR200(P) computer case by Cooler Master. It needs supports to be printed.
Stud for mounting slim fan (15mm x 120mm) on on top of NR200 or NR200P itx case. Use finer settings to print for optimal quality.
A bracket for mounting HP EliteDesk 800 G3 power supply inside CoolerMaster NR200/NR200P case. I don't know if this is the best placement for the PSU but I wanted to get it done as quick as possible so I took 2 models and remixed them.…
A bracket for HP EliteDesk 800 G3 SFF motherboard for mounting in Cooler Master NR200 NR200P cases. It's likely you can also use it for mounting inside other mATX and ATX cases but I have not tried it myself. This is a low effort model,…
Backplate to be used with my motherboard offset plate. I recommended printing it with some higher temp resistant filament like PETG. I've used orange Prusament PETG. I personally have RX6400 GPU so there is an additional cutout for…
A set of brackets used to mount 4 3.5" HDDs inside NR200 case. They mount to the side panel 5 screws. I believe the screws are M5 diameter, 10mm long. HDDs mount with standard hardware.
I put a MSI Geforce 4080 Super Ventus 3x in a Cooler Master NR200. Tight fit! In this case the GPU sits horizontally and the card is very long and unsupported at the front. Because I will need to move this PC occasionally I made this…
I wanted taller feet to keep the underside air intake further away from the carpet so I made these. Printed in matte white PLA, .2 layer, 100% infill, they look good and feel plenty strong enough. Left and right feet are joined for…
My computer sits next to my desk and I often want to pull it out to access the rear ports and then put it back. I made these wheels for the back to make that easier. They use 70mm roller blade wheels and axles (get from skate shop, they…
A panel clip for the NR200 which allows taller CPU coolers to be placed in the case.
First, a shout out to the following creators whose GPU support models saved me a lot of time since they already had modeled the front panel hole locations. unknow1assassin | Printables.com aeberbach | Printables.com This is a GPU support…
I got a new mainboard with a USB-C header. That's a lot more useful on the front panel than the front panel audio to me, so I got https://amzn.asia/d/h0ZvS1F and made this adapter. The NR200 has a separate PCB for the audio jacks so it is…
This collection offers four different designed front panels. Example pictures show models printed in PLA on a Bambu Lab P1S. Panels A, B, and C are available in two versions. The first version has the mentioned panels come in two parts,…
Increased foot height to perform a better cooling and to be able to clean dust under the case.
Brackets to mount your PC to your desk I wanted a visually cleaner workspace so I wanted to mount my PC to the underside of my standing desk (before it was sitting on top) This is specifically for the CoolerMaster NR200 case (when laid on…
To use this you need to add some threaded inserts so that you can use some m3 screws to screw it in place. It uses the holes that are already in the case so no need to drill some ;) What you might have to to is hammer down the marked part…
TLDR Deshroud mod for the Ventus 3080/3080Ti/3090 in the Cooler Master NR200 case Fan shrouds designed to perfectly fit the Arctic P12 and bridge the gap between the fan and the GPU heatsink The Normal Fan Screws version of the fanshrouds…
NR200P V3 Top Shroud (6" Duct) I designed this top shroud for the Cooler Master NR200P V3 due to finding how much heat it generates with a setup of a 5090 and a Ryzen 9 9950X3D! Now with this shroud connected to a 6" duct exhaust with a…
So I decided to transplant my old loop with an EKWB A240G aluminium loop into an NR200p. Seeing how it is recommended to have a EK-XRES 100 SPC-60 MX PWM (incl. pump) in the vertical orientation (according to the manual). I decided to…
I made this as i was unsatisfied with other existing slim fan tool less pins that were already uploaded. 4.10mm may be tight on some fans, its a tight fit for the UPSIREN fans i had. was not able to try others i have made a 4.00mm version…
This is a extension pin and clip that allows you to use the existing factory clip and extend the side panels out by approx 15mm. This does not require you to remove the original factory clips, they push into the original clips and then…
A simple plate designed to protect your power button from undesired presses. It hooks into the two USB-A ports and has chamfers on the sides to make it easy to lift out. My one-year-old loves walking and pushing buttons. Unfortunately,…
Intended to be used for Cooler Master NR200P bottom exhaust, it guides hot air to exhaust to one side of the case, so it doesn't heat up my hands and keyboard. I printed this with PETG filament, as the exhaust can get quite hot. Not sure…
Designed these PCIe slot covers for the NR200 to give the CPU cooler a bit more air, also they snapfit ! Note The covers are dimensioned using ABS which shrinks a bit more than other plastics, so if it's too loose for you, try scaling the…
TLDR Deshroud mod for the MSI Ventus 3080/3080Ti/3090 in the Cooler M case Fan shrouds designed to perfectly fit the Noctua NF-A/F/S12 and bridge the gap between the fan and the GPU heatsink 2 Versions available for use with & without…
TLDR Deshroud mod for the MSI Ventus 3080/3080Ti/3090 in the Coolermaster NR200 case Fan shrouds designed to fit any standard 120mm x 25mm computer fans and bridge the gap between the fan and the GPU heatsink Fan shrouds can be mounted to…
Cover have 2 versions. One of them with hooks to attach it to the bottom edge of the PSU bracket. Even if you don't like this solution- just break off the hooks.
This custom NR200 front panel fits the v1, Max, and v2 cases with a clean, drop-in design. It’s divided into two sections to allow printing on smaller 3D printers without sacrificing strength or aesthetics. An extra 10 mm of internal…
This custom NR200 top panel fits the v1, Max, and v2 cases with a clean, drop-in design. It’s divided into multiple sections to allow color customization and printing on smaller 3D printers without sacrificing strength or aesthetics. The…
This custom NR200 top panel fits the v1, Max, and v2 cases with a clean, drop-in design. It’s divided into multiple sections to allow color customization and printing on smaller 3D printers without sacrificing strength or aesthetics. The…
This custom NR200 front panel fits the v1, Max, and v2 cases with a clean, drop-in design. It’s divided into two sections to allow printing on smaller 3D printers without sacrificing strength or aesthetics. An extra 10 mm of internal…
With this frame you can use 120mm rear fan instead 92mm. Ensure that VRM heatsink does not interfere with the installation of this mod.
Materials Screws 8x Original screws from feet 8-14x M3 x 6mm 2-4x per Support Bar to Side Rail I use 2 per bar, but there are holes for 4 1x per Rear Side Plate to Side Rail 14-22x M3 x 8mm 4-12x Side Rail to Disk Drive 3x per Front Side…
I have a 4090 horizontally mounted in my NR200 Mini-ITX case and needed to drill out more ventilation holes in the steel sheet metal side panels. This drill jig will slot into existing holes so you can line up the precise pilot holes for…
EDIT: v2: better support for mounting hard drive with top facing right. Most SATA angle cables are only down, so mounting the hard drive on it's right side/clockwise will allow use of these cables. This is a remake of the official Cooler…
My Framework Desktop Mainboard was hitting 100 C during inference while using the stock fan duct, which is obviously a problem. Not only does this replacement duct provide greater airflow to the 120 mm cooling fan, it extends to the side…
The original mount holes for the PSU bracket are covered by the mATX motherboard. This bracket allows you to still install the PSU to the side of the case with a duct for getting cleaner airflow from the side vent (otherwise it tends to…
This is a remix of the remix for the the Snapfit NR200 PCIe Slot Covers, designed to snap onto the back of the case where the vertical GPU support is located. it is based on the reinforce model to be more sturdy the vents are angled to…
The default orientation for a 3.5inch HDD in the NR200 puts the connectors right next to the CPU fan and above the 24 pin, USB3, SATA, etc on most motherboards. This is very crowded and I had to bend my SATA power cable a concerning…
To mount this, you take out two of the power supply screws and put them back in through the mount to attach it to the psu shroud. Then you slide the drive in and screw it into place. Tolerances in this spot are very tight, you'll want 90…
U-Shaped Feet for the NR200/P originally created by Erer2001. I have increased the overall feet height to 3.5cm and increase the thickness in order to strengthen it due to being higher.
This is an IO plate that can be used to relocate the front IO panel when flipping the case upside down (inverted mode). It will fit into the hole behind the front panel.
Also remixed from ivtue's excellent NR200 controller holder found here: https://www.printables.com/model/541806-nr200-controller-holder I kinda just mushed the two together and filled some holes to get the design you see now. There is a…
Bracket used to mount a small water cooling reservoir inside the NR200 case. Designed specifically for the EK-RES X3 150, a standalone reservoir (no pump) that fits inside the NR200. Should fit GPUs up to 295mm long in the vertical…
Frame will give you another 9mm of width. Frame V2.0 (TG and metal and radiator mount compatible) 7-part print. Radiator spacings fixed, they are now precise. Also made holes 4mm big to accomodate Deson m3 screw inserts in radiator mount…
Designed to mount an NZXT Kraken X63 (280mm AIO) on top of the NR200P. Glass and Mesh-Panels still can be used, also standard top cover fits perfectly in. All Connectors should be printed with PETG with min. 25% infill. Material of…
I wanted to make use of all the space available on the bottom of my NR200, so I made this adapter to fit two 140mm fans instead of having two 120mm fans and some unused space. I made this 9.5mm high in order to fit the adapter and fans…
Features an offset so that a standard 3.5" HDD ends up sitting 17mm left and 10mm up relative to the original plate. This is to make more space for cables or fan hubs mounted to the right of the HDD on the inside “wall” of the front…
3 shell, iron the top surface for better look. Very easy to print.
x2 usb 2.0 breakout, x1 usb fingerprint sensor, x1 usb to usb c adapter, x1 Apple usb c DAC. The fingerprint sensor is easier to reach if the pc is on the desk top. Also Apple's cheap usb c DAC have great audio and the ADC is way better…
During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…
During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…
During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…
During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…
During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…
During the development of the Cooler Master MasterBox NR200P , we created several variants for the case feet design. Following numerous iterations, the launch design was chosen, but we thought "why not share the iterations with our…
Compatible with Cooler Master's MasterBox NR200 and MasterBox NR200P . The design of the bracket is ventilated for actively cooled units to be installed, independently from the orientation of the intake fan. The bracket is also compatible…
Compatible with Cooler Master's MasterBox NR200 and MasterBox NR200P . We are making free to download, remix and modify the design of the top panel of our most beloved ITX enclosure(s)! You can easily modify it to add support for a…
Compatible with Cooler Master's MasterBox NR200 and MasterBox NR200P . We are making free to print and modify the design for the clips that hold the paneling of our most beloved ITX enclosure(s)! Lost one? Your product is out of warranty?…
This bracket supports the GPU by bolting to the back of the GPU and the bottom of the NR200 case. I designed the bracket for my RX6800 reference, but I think it should also work for the RX6800XT, RX6900 and RX6950XT as they seem to have…
This model snaps into the hole behind the power supply in the NR200 case through which the power supply intakes air. Normally there is a gap between the PSU and the ventilated side panel of the case, which allows the PSU to intake warm…
This model will only work for this exact combination of case, cooler and motherboard! Any other combination will most likely change the position of the cooler in the case. Feel free to remix.
I've inserted magnets in the bracket to snap it to the case, but I've included a solid version to tape down or add your own holes for magnets.
I didn't want the included mesh top panel to restrict exhaust airflow so much, so I made this Cooler Master NR200/p top panel hardware to allow external fan grills to be installed to the top of the case when the mesh is removed. This can…
masterThis is a top cover intended to replace the mesh of the top panel on the Cooler Master NR200 PC case. The cover leaves cutouts for the top fans (intended for use with fan grills via my external mounting hardware at…
I stuck mine on with double sided tape, but glue should work too.
I've glued, sanded and painted the bottom in the photo, which is why the join line and layer lines are mostly hidden. The original model by tangcla is on Thingiverse, but I reuploaded it here with permission so it can be added to my NR200…
Mount slim fans on top of Cooler Master NR200P case. I wanted my PSU to hang higher inside the case to help with cable management, however that caused the power plug to collide with the stock 25 mm thick fans. So I made this to install…
The “--clear” version does not contain additional surface for better adhesion during print.
Print flat side down. To install, loosen or remove screws at the far end of the GPU and at the GPU IO plate of the side case frame. install the support and reattach frame. Support me on ko-fi. Updates 2023/01/05 Removed cross beam near…
Bracket to mount an ATX power supply in the Coolermaster NR200/NR200P. This only works if you have already inverted the case. The two “pegs” slide in under the little sheet metal edge in the front, and the bracket then screws to the…
A 10mm shortened version from Zocazol. Slightly beveled + reduced hole for better fixing of the side. I did this for my Noctua D15 which fits just right. The lower extension brackets are not needed, stick to the original bracket. If you…
Cover designed to stick into NR200's USB ports. Main purpose is to prevent cats from turning off your PC while gaming :)
This fan shroud was created to redirect air into the radiator of vertically mounted GPUs in the Cooler Master NR200(P) case. Created to fit any 120mm fan. Baseplate can be shrinked for added clearance. Countersunk screw holes created to…
This is a 3d printable back panel made for the Cooler Master NR200P to allow for a vertical-mounted GPU and a top-mounted AIO. The printed mod changes the position of the motherboard down 26.5mm, GPU down ~63.5mm, and moves the internal…
To invert the case u have to just filp it upsidedown, swap top and bottom panel. This mod involves permament change to the case, you have to cut off 3 threded standoffs. The front panel isn't perfectly symetrical, so after the mod you end…
This is a clip wich hold front pannel on coolermaster nr200 PC chase. I redisign it by myself, but it looks like original on this site. In my disign no parts in the air, you can print it on a side without support. And differend oval shape…
Print in PETG as you will run into reliability issues with PLA.
Basically, this is a relatively easy mod that drops both CPU and GPU temperatures while running the fans at lower speeds which also resulting in much less noise. It is specially optimized for Noctua NF-A12x25 fans and FDM printers. To get…
