Counting matching models…
As seen on X and YouTube: Disclaimer: This is an acoustic model. As such, it does not scale, nor is it compatible with drivers other than the ones specified. Scaling / incorrect driver(s) will result in significantly diminished performance.
did not find a high-quality keychain model and decided to create my own version
Cabin for a MAN truck in 1/10 scale. The cabin is just a fragment of my MAN truck design, category 8x8... more about the project can be found HERE The roof hinge is a 2mm steel rod. Video of the first truck ride Video from the first…
A remix of Hexibase's subwoofer designed for clear side panels, so the cool waveguide is visible. It would also suit wooden sides. It's smaller than the Hexibase version, so it will print on a 19cm x 19cm print bed. I kept exactly the…
Subwoofer or speaker protection for 8 inch driver. Measurements: Guard face: Outer diameter: 200 mm Inner diameter: 176 mm Height: 10 mm Legs: Outer diameter: 263.9 mm Inner diameter: 239.9 mm Height: 30 mm Total height (legs+face): 40 mm…
Subwoofer port I designed for my cheap car subwoofer. Included is an .obj file so you can edit it to your own needs. Print Settings Printer Brand: Monoprice Printer: Select Mini Rafts: No Supports: Yes Resolution: 0.2625 Infill: 20%…
Also included STL's in case others didn't want to deal with the .3mf file.
The walls are 13mm and i made the volume at recommended for a vented enclosure excluded the speaker. It's built with tongue and groove for easy and strong assembly. Use low viscosity glue. The TCP115 is a very good woofer for the money. I…
Introduction A few years ago @HexiBase_264072 built several versions of a 3D printed subwoofer using the Tang Band W3-1876S 3" driver. These designs take a very long time to print though, so I made a version of his design that is hollow…
Length : 188mm Width : 90mm Included is fusion360 file and STEP file, so you can edit it for your needs
Simple 4 Inch subwoofer using a Dayton Audio 4" long-excursion driver in a ported box. The box is braced and printed at 50% fill, although the brace is printed with 80% fill. I used cotton stuffing on the back and top wall near the…
Designed this for Alpine R series 6.5" woofer and 3" midrange speakers. But, may work for other speakers with same bolt pattern. The pod retains the factory speaker angles relative to the door, but adjusts the depth to provide clearance…
As seen on YouTube: Disclaimer: This is an acoustic model. As such, it does not scale, nor is it compatible with drivers other than the ones specified. Scaling / incorrect driver(s) will result in significantly diminished performance.
Instructions from creator: 0.3mm layers 3 shells 4 top and bottom solid 40% triangle infill I used 0.2mm layers
Sub woofers are using a combination of 3D printing and micro cement (jesmonite) the full range speakers can be printed in PLA. Build video and sound demo here:
Protective cover for Samsung Q990F. Printed from PLA, no supports required. Only additional hardware required for assembly is a little bit of double-sided sticky tape around the beveled edge. I just used four (4) small strips 90 degrees…
Building 3D Printed Speakers — Complete 2.1 Setup
I've been working from home for over a year and felt my PC desktop audio system needed an upgrade. This sub-woofer is based on the Peerless Tymphany SDS-135F25CP02-04 5.25 inch driver which costs < $30. I 3d printed the cabinet using…
Here is my latest speaker system, it's a set of hi-fi grade speakers designed to be printable on small-bed 3D printers, including the Prusa Mini. It's a sub-woofer and satellite system usable as a 2.1 stereo system, or a home cinema…
Anpassungsbedarf! Nach einem ersten kompletten Druck mit PC Blend und einer vollständigen Montage habe ich einige Defizite festgestellt. So liegt der Auflieger etwa 3 - 4 mm tiefer, was nicht zweckmäßig ist. In Verbindung mit der…
If you're a retrogamer or a collector of retro tech, or if you like high quality audio and invested in a receiver with external speakers and a subwoofer, you've probably run (or know someone who ran) into the problem of RCA connectors…
This is a 3D printable cabinet for an 8" powered subwoofer by Deposition Sound LLC. If you have a medium/small living space that is in desperate need of thick, juicy, and fast bass, these are just for you! They have been carefully tuned…
1/87 Goldhofer 4 axles trailer / Printed with 0,25 nozzle on Prusa Mini+
1/87 Goldhofer 6 axles trailer / Printed with 0,25 nozzle on Prusa Mini+
Greetings, A few months ago I began designing, building, and testing 3d printed speakers using the SB Acoustics SB15 and SB26 aluminum drivers. The tweeter on all three designs use the Somossonus (AKA Augerpro) waveguides, but with some…
Intention to print these 4 parts and then use ½inch nominal (0.472 in) plywood for top and bottom. To use threaded rod (¼-20 or similar, those are 6.5mm holes) to clamp shut I'm finding 400-800g per part, so this is a plastic hog… I'm…
Try this as a smoother, less broken-up version: 20 cm x 20 cm Print Bed Version This is a modified version of the subwoofer enclosure, split into smaller parts so it can be printed on 20 cm x 20 cm print beds. I added connectors to make…
1/87 Goldhofer 5 axles trailer / Printed with 0,25 nozzle on Prusa Mini+
Protective cover for Samsung Q990F based on @aballacchi_1376836 design. The original file has about 5mm of clearance from the subwoofer cone surround in its natural position. I wanted to use up some PETG I had lying around, which has the…
I am converting a passive subwoofer to active, and so got this amplifier from amazon: https://smile.amazon.com/gp/product/B01N5DGK37/ It comes as a bare board, so I needed a case, this is it. The first run fit pretty well, I had to use a…
Designed for the Edge 750W 10" car subwoofer You will need supports! 2 types, different mesh thickness!
My subwoofer enclosure. Printed in PLA at 25% infill The feet were printed in TPU and glued to the bottom of the subwoofer.
I've created this model for coupling my subwoofer in my office. The subwoofer sits on a carpet which is, to my understanding, is not ideal for the sound waves. Therefore, I created this model and used double-sided tape to attach it.…
model upload https://www.youtube.com/watch?v=dpwPDGCEb80 design by Nathan Bulle
Zunftzeichen Dachdecker
This is a 1:6 scale replica of the legendary SVS PB-17 Ultra home theater subwoofer. It's designed mostly just as a toy but I was surprised how good it actually sounds! Definitely a decent bluetooth speaker. UPDATE: I just made a larger…
Update june 2024: IT still WORKS, I had it in my car for over 16 months and ABS survive -30C to +40C (outside temps). Sounds amazing!!! I love this mod so far and I don't want to get rid of the car because of it. 10 inch Subwoofer adapter…
Andere Modelle https://www.printables.com/de/model/692988-happy-new-year https://www.printables.com/de/model/109448-good-luck-pig
Adapter for a VW T5.1 to mount Audison APK 165 set. Printed with PLA: 4 Walls 3 Bottom Layer 4 Top Layer 0,32 layers Designed after the OEM-Holder and to fit on Ender 3 with 220 x 220mm buildplate If you need diferent diameter on the…
Made for SVS Subwoofers but can be used with others aswell. Needs a ¼-20 bolt, 15-20mm length I used ABS-GF and TPU 90A to print these parts. For feet i used 2 walls with 8% gyroid infill with 90A TPU, that gave good results with SVS…
Adapter für die Führungsschiene von Makita auf einer Hofer/Aldi Schnellspannklemme. Adapter for the Makita guide rail on a Hofer/Aldi quick release clamp.
I swapped out the stock speaker in my Stern Godzilla, RUSH, and Iron Maiden for a Blaupunkt GBW801 subwoofer. Because these speakers are mounted INSIDE the cabinet (unlike a subwoofer box for a car stereo), they require something to lift…
You’ll need this if you are doing a sound isolation in your MK5 Supra to fix the subwoofer rattle. Follow one of the tutorials below https://www.supramkv.com/threads/how-to-improve-oe-sub-bass-quality-and-eliminate-vibrations.5092/ I have…
You can use this to allow a Rockford/Fosgate 8 inch subwoofer driver to fit into a 2017/2018 Audi Q7, replacing the BOSE driver. The upgraded driver is under $80 and weights twice as much as the BOSE unit, and has more travel. Note that…
I created this wall mount to get the subwoofer of the Logitech Z333 Soundsystem attached to the wall. Found wall mounts for the speaker and Volume-knob here, but not for Subwoofer. The distance to the wall is needed, because the cables…
These are flared inner and outer ports for subwoofers. I used a 4" ABS pipe as a tube. They have a 1" roundover section of flare, and ½" of mounting thickness. Designed to be printed on a Prusa Mini. I had to print the flanges facing…
These are speaker adapter mounts for BMW E46 front doors. There is a mount for both the tweeter and woofer. The mounts are designed for a JL Audio C3-525 component set but I have included generic .stp files for the mounts to adapt the…
Nachbau der Felgen für den Carson-Auflieger im Maßstab 1:14, bestehend aus einer inneren und einer äußeren Felge Es sind noch drei Schrauben erforderlich, um die beiden Felgen zu verbinden. Zudem sind zwei Kugellager erforderlich, um die…
Nozzle: 0.6mm for best results Material: PLA, ABS Supports: Yes Driver: Tang Band W3 1876s (ND90/91 version will be added later) Radiators: Dayton ND90-PR Amplifier: Hifidiy live 2.1 amplifier from Aliexpress. Any version will work, but…
A few years ago I made a small, poorly made box for a Tang Band W5-1138SMF 5 1/4" subwoofer plus two 6 1/2" radiators. It worked and sounded alright but now that I have developed better CAD skills and understand the modifications I wanted…
Griglia per altoparlanti Ipnosis 20cm,adatta anche per altri altoparlanti.
Design for a 12 Inch Subwoofer for my Rzr roll bar. Videos: https://youtu.be/ib4kLUPlFtU https://youtu.be/xPikC_gUs3Q Things to note. You need a LARGE scale printer to print this. It takes over 60 hours to print this. It does not have…
Simple “Foot” Replacement for Logitech PC Speaker Sub. I purchased a set of speakers for cheap and it was missing the rubber feet on the bottom, i modelled this to be used with standard wood screws ( i just had some laying around ) print…
Battery holders for Activ Energy batteries usually sold in ALDI/Hofer. You can select between two types, one is for vertical and horizontal mounting, the other is angled 25° for easier access
I made these feet for my DIY downfiring subwoofer, I found commercial solutions lacking and printed solutions non-existent (at the time of creation, by 2025 this changed). There is two variants - 50mm total height (shown in the graphic)…
this is a casing vor the TPA3116D2 (AOSHIKE 8-25V 100W TPA3116 NE5532) amplifier. this is a lowpass mono amplifier for subwoofers. More information: https://www.youtube.com/watch?v=SO96JDnXoRg (not my video) where i bought the product…
I have added a dedicated channel for 16AWG speaker wire and a dedicated enclosure on the rear for RCA jack. If you have TPU filament, you can print gaskets that will work perfectly. If not, you can still use normal gasket cord material;…
It's hold in place only by friction. The sides have a small ‘cut’ so it fits on an MK3/MK4 print bed. I printed it in Prusament PETG with the front down on the bed. onshape document:…
This subwoofer features a large triangular port, a hallmark of most of my designs. Its generous volume and dual drivers, which operate mechanically in parallel, allow it to achieve a low-end extension down to 45Hz and even lower, perfect…
In the past few weeks I received 3 separate requests for the matching woofer grille for an older design I made earlier. I had some spare time and decided to finish the woofer grille I had already started designing a long time ago. Since…
Dieses Modell dient dazu, mittels des Lenkkeils und der drehbaren Platte den Lenkwinkel zwischen Sattelzugmaschine und dem Goldhofer Sattelanhänger an das Linearpotentiometer von HAMAtronic an die entsprechende Elektronik zu übertragen.…
Very crude enclosure I've designed for the 6th gen Broncos to fit a Hifonics BXS10D4 which has a mounting depth just shy of 3 inches and is relatively inexpensive. This was modeled using my 2022 2-door full size Bronco so I can't make any…
Designed to fit a Jensen CS10 Powered Bookshelf Subwoofer cabinet, but easily scaled to fit other audio equipment. The original rubber leg had a steel washer to make the screw hole rigid, but I've been able to skip that piece. The screw…
Basic subwoofer legs to get your subwoofer off the ground. Can be used on other objects as well, of course :) Can be mounted using a single screw. There's a small indent/cutout on the bottom in which you can place some felt or rubber to…
Needed to deepen the subwoofer in to the front of the speaker box so i made a guide for the router. you need a 5mm bolt and a 5mm drill the routerbit is 12mm wide
A small subwoofer model for model cars and such. Size to your needs. Category: Hobby
Ash tray filler panel with cut out for rocker switch Added version for subwoofer knob and pocket to hold remote. Printed in ASA. Tight fit. Once it's in, be careful trying to get it out!
This adapter is enabling instalation of new underseat subwoofer BLAM BM200W to original BMW box. BLAM BM200W in comparison with BM200XF needs deeper instalation space for BMW 3GT (F34) with HiFi option. Adaptor increases instalation depth…
This was deigned to replace the factory subwoofer in my 2023 VW Jetta GLI with beats audio. The factory subwoofer leaves a lot to be desired, this sub performs very well in this spot and is a simple plug and play drop in with no…
void series loaded loudspeaker
The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. 0.15mm is recommended. It fits all Woofers, best fit for 165mm…
This great sub-sat system requires a print area of 200x200mm for the subwoofer, and slightly less for the satellites. These use sealed speaker modules from Tang Band; the full range T1-2121SD in the satellites, and the T2-2181SA subwoofer…
This jig can help you drill perfectly placed perpendicular holes in a speaker or subwoofer baffle. Includes a parametric Fusion 360 model that can be customized to your project and an stl that is configured for a GSG Audio BTS sub…
This is a replacement foot for the JBL Bar 5.1 Subwoofer, my original one broke off this uses the original screw + rubber pad
ISSB | Speaker Box for Smartphones - t he ISSB - i Phone Sound Subwoofer Bassreflex - Docking Station is a compact subwoofer that will amaze you with its surprisingly precise and punchy bass. It might be small enough to discretely tuck…
Front subwoofer enclosure for a MK7 Golf (left hand drive). Designed for the SB Acoustics SW26DAC76-3-DV. Version 1.1 is the one I ended up using, and added 1" of plywood on the front to make it stronger. If you have an incredible amount…
See edit at the bottom, for added speaker choice Tang Band W5. xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx Small ported subwoofer around 12L volume, can be extended to 18L (or more) if needed. The middle…
Needed slimmer feet to fit it inside a tight space under my TV closet.
Enclosure for chiniese bought subwoofer amplifier, I have designed it to be glued together, once put together, box have no openings for wires or any type of plugs, as that can be drilled if anyone have specific needs as per that.…
Servoaufnahme, um einen Standardservo zur Ansteuerung der meiner Lenkachsen aufzunehmen. Er wird hinten durch die ersten Anlenkungen der Achsen fixiert, vorne sind zwei Bohungen im Rahmen des Goldhofer erforderlich. Damit wird zugleich…
After purchasing a new subwoofer, I soon found out that the old windows in my flat rattle when the full bass power is unleashed. This led me to try to isolate the vibrations transferred to the floor from the subwoofer. I've combined the…
Разъем для подключения колонок или сабвуфера Данную модель вы можете приобрести тут: https://cults3d.com/ru/3d-model/gadzhet/speaker-subwoofer-input-connector-70x60 Рекомендованный размер саморезов: 20x3 - 4 шт. Рекомендованный размер…
I bought a new speaker set from Monitor Audio and am very happy with it. However, I had to notice that the hard plastic feet of the subwoofer caused the subwoofer to slide around on my parquet floor when there was extreme bass. That's why…
Gedruckt in PET-G
On pictures installed to 2016 XC70 volvo.
Brackets to mount an Alpine PWE-S8 powered subwoofer in the trunk of a Tesla Model 3 SR+ where the factory subwoofer is located in other trim levels. I mounted the subwoofer to point into the rear fender cavity ("corner loading"). Others…
The holder can be printed from any material. No supports are necessary when the model is placed on the build plate with the foot facing down. A layer height of approx. 0.15mm is recommended.
Wanted an angled stand for my KRK S10 subwoofer, and most were a bit too small, so I made my own. The lager model in the pictures were printed on an Ultimaker S5 with a maxed out build volume. The square one is meant to comfortably fit on…
This simple wedge printed in flexible filament will help eliminate vibration with the rear deck in the 2016 and 2017 Honda Civic Touring. Simple place the wedge between the front lip of the opening for the 3rd (center) brake light and the…
Akkubox für Goldhofer Sattelauflieger mit Deckel im Maßstab 1:14 zur Aufnahme eines Standardakkus, Zusätzliche Aufnahme für eine Servonaut-AMO-Elektronik. Der Deckel wird mit Neodym-Magneten (5 x 3) gehalten. Dafür ist in der Akkuwanne…
.. see photo :) required really good cooling, used PETG for more flex. Filament ist PETG Silver from Extrudr Print Settings Printer: Kossel Delta Printer Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Notes: i used support for the…
Made specifically for Polk Audio DB 842 DVC, which has a 96.5 mm top mounting depth and a 196 mm diameter octagon screw pattern. The Polk sub is a great step up from the factory subwoofer without amp upgrade (my Civic comes with a 540W…
Dieses Modell dient dazu, mittels des Lenkkeils und der drehbaren Platte den Lenkwinkel zwischen Sattelzugmaschine und dem Goldhofer Sattelanhänger an das Linearpotentiometer von HAMAtronic an die entsprechende Elektronik zu übertragen.…
I wanted to replace my decade old logitec z506 setup for my pc - this is better. I designed this ported subwoofer box for a 5inch driver i found on aliexpress. Its paired with 3" full range drivers in sealed boxes i designed. Speaker…
I created this model as a cool project for a friend. I got a lot of interest in it as people saw the set up. Designed to use two B2 Audio Rampage RC2. It also uses the speaker terminal cup from Parts Express (260-300). I printed this with…
