Counting matching models…
Recommended slicer settings: Layer height: 0.1 Initial Layer height: 0.1 Infill: 100% Print material: Preferably ABS+ or ASA, although I've printed it using PLA and it's holding up well. Tutorial: A good tutorial on how to use the shims…
Same as original with sloped side and without logo
Ant Feeder Collection - SLOPED EDGES Square Feeder 39x39x7mm Round Feeder 44x44x7mm 3 Compartment Feeder 39x49x7mm
EASY PICKUP- Ant Feeder Collection Square Feeder 39x39x7mm Round Feeder 44x44x7mm 3 Compartment Feeder 39x49x7mm
SLOPED Standard-sized WHOLE PANS for your Watercolour Palettes! Two versions! One with a flat area at the bottom only, and the second with a flat area at both the top and the bottom of the slope. The horizontal layer lines which are a…
A pottery rib for throwing a pot or cup with a small foot and then a gently outward sloping wall. The rib measures 150mm tall. Measurements are on the rib to help check sizes while throwing. I print mine with PLA and don't have any issues.
Glaxy Black PETG used with 0.1mm layers - the parts are so small the print takes no time and they are very visible so good to have a nice finish. They are a nice press-fit.
Version of Duplo brick generator, where you can generate sloped bricks. Not perfect, there some bugs but works fo some basic designs. There a STL file for standart sloped brick with 2x3x2 70676 base which is default in the generator. It…
An Oloid is a developable surface made by intersecting two circles at a right angle and lofting the surface between them. Print instructions Note that the file attached is 1/4 of a full Oloid . In order to get the print to sit flat on the…
Just another card holder (sloped) for ARK NOVA. It is big enough to hold even sleeved cards! Looks pretty good when printed in 3 colors as shown on the pic. If you use UNSLEEVED cards: Print with 0.2mm layerheight. Start with BLUE and…
Work in progress. Not tested myself. A downwards and sidewards sloping wedge for the new Google Nest Doorbell (battery). It's sloped 20 degreed to the right and 5 degrees downwards. Measurements based on original Nest Doorbell (battery)…
A Sphericon is a shape with 2 edges and one continuous face similar to that of a Mobius Strip. A Hexasphericon is a variation of this shape made by revolving a hexagon around its central point, slicing, and rotating. Print instructions…
When we bought our 12V PARKSIDE Performance screwdrivers in LIMITED Bauforum24 Edition from LIDL we wanted to protect the nice and unique color display on the backside from any dust and scratches. So we developed this rear protector which…
SLOPED wallmount battery holder for the 12V PARKSIDE Performance ( Bauforum24 Edition) cordless screwdriver. The base is 60x70mm. The angle between mount and baseplate is 25° which allows a more comfortable use depending on the place of…
A pottery rib for throwing a pot or cup with a wall that has a single gentle slope outwards halfway up. Measurements are on the rib to help check sizes while throwing.
This is a remix of Mike's mesh . I changed the mesh to half the size (148.5mm x 105.0mm) for a smaller print bed. I also added a slope (2cm → 4cm) so that filament can be fixed more secure inside the box and does not move around when…
This model is compatible with the lego system.
When we bought our 12V PARKSIDE Performance screwdrivers in LIMITED Bauforum24 Edition from LIDL we wanted to protect the nice and unique color display on the backside from any dust and scratches. So we developed this rear protector which…
This display shelf is part of the Sloped Lines collection, a blend of modern design and practicality. The collection includes a pencil cup and letter tray shelf . The shelf can be printed as one piece. Undivided, larger versions are…
A little Hook for mounting your Snowboard to a sloped wall/ceiling. Just screw it on the beam and you're done.
Just a smaller version of the original design. My work table is too small for the original design.
Design & Installation The light consists of three individual pendant shades suspended at different heights from a shared canopy. The canopy is split into two parts: A wall / ceiling mount that is screwed directly to the ceiling A canopy…
Mounting the two drop-lights directly to the sloped ceiling would have looked odd, so I designed this part. For the dangling cables I designed a connection box to be mounted at the location of the old lamps. Additional required parts:…
his holder makes it easier to have e.g. the yoghurt (or e.g. sour milk) package standing upside down in the refrigerator to have the remains pouring down to the opening. This holder fits packages where the cap is on the top, e.g. Tetra…
Raise your Reliq up on a angle for ease of use. You will need to print two copies of the lower and upper angles. You will need at least two of the connectors. I found it stable enough for me with just two. Assemble the slopes first.…
Part of the Sloped Lines Collection, this stand is a good place to put phones and tablets. Supports are needed for the short section in the front, only.
Sloped stand for the well known VICTORINOX swiss (pocket) knifes in original Victorinox present boxes. There a TWO versions available: With & without logo. This modell has been made for the Victorinox knife boxes 85,5 x 60mm. If you have…
This allows dual RCA phono jacks to be mounted inside a case where the back panel is sloped at 45 degrees. I have a Revox B790 turntable that I am refurbishing and the phono cable was hardwired. This will allow me to disconnect the phono…
Turn that cd mount on your car into Andrioid auto with this rasberry pi case for this screen and sloped cd mount for a easier install
A specialized 3D-printable mounting system designed specifically for sloped or attic ceilings . This 3-part bracket solves the common problem of installing standard curtain rods on angled walls (approx. 45°), providing a secure and…
Same as H_Alex's but sloped to fit my roku remote better Category: Parts
Round magnetic flower pot holder useful to hold your plants in place on too sloped window sills. There are feet for 5 mm x 1 mm magnets on the bottom side, use superglue to glue them in. I included the OpenSCAD source for the model so you…
A family of three hanging bins for standard 1-inch (25.4 mm) pegboard with 1/4" holes. Mix and match them to keep screws, electronics parts, hobby supplies, 3D-printing spares or office bits right where you can see and reach them. SIZES S…
Various mounts for 3/4" PEX piping to mount to a wall or ceiling. I used these to run a curtain rod for a green screen in an A-Frame house with 45° sloped ceilings, with one mounted to a flat wall. The type of piping used is easily…
If you frequently reach for different assortments, this shelf organizer makes them much easier to browse. Instead of lying flat or stacked, the boxes are organized on a row like books with labels easy to read and contents visible at a…
A soap dish that doesn't leave your bar sitting in a puddle. The soap rests on rounded ridges above the floor, and the floor slopes gently towards an opening in one end, so water runs off between the ridges and out. Put the open end at…
Designed this after losing one too many beers to the DBG concert lawn slope. The "spike" will break if you apply too much torque to it, but if you press straight down it should hold enough to stay in place. Would welcome anyone…
A deck board has to sit level on a zinc flashing that slopes . A solid shim does that, and creates the problem this one is built to avoid: it dams the runoff, so water stands permanently between the wood and the metal. That puddle matters…
Just a smaller version of the original design. My work table is too small for the original design.
This allows dual RCA phono jacks to be mounted inside a case where the back panel is sloped at 45 degrees. I have a Revox B790 turntable that I am refurbishing and the phono cable was hardwired. This will allow me to disconnect the phono…
Various mounts for 3/4" PEX piping to mount to a wall or ceiling. I used these to run a curtain rod for a green screen in an A-Frame house with 45° sloped ceilings, with one mounted to a flat wall. The type of piping used is easily…
This model is compatible with the lego system.
Remix of https://www.thingiverse.com/thing:4622671 Made the hooks a bit more dull and added a sloped guide at the end. This makes it easier to place the topper on the can as the guide will slide on the edge. To make it even easier to use…
I add a slope to the original Peggit clip and the modified Pegget clip for SKÅDIS . This sloped version allows for better mounting to the receiver end in prints that need to be oriented vertically, like my other models that use the Peggit…
This model is to be screwed into the inner side of a frame for a picture or poster so it can be hanged on a sloped ceiling/wall. There are cutouts provided in the model to slot over a screw that can be drivin into the wall or sloped…
Laser Baseplate for Revo7 crossbow side mount to mount Fenris Laser Module. You might try to fit it to a Revo12, but there is no function guarantee. Replaces one side picatinny rail. The inner holes are for insertion of 8mm M4 screw…
A small edit to Leon_H's Spirit Island Vitality Token box to add a sloped edge for easier removal of tokens.
DF64 Blind Shaker Mount - Sloped with Hook. Designed with a forward slope to prevent coffee grounds from accumulating around the base and screw hole. The integrated hook secures the blind shaker in place, preventing it from slipping or…
This model is compatible with the lego system.
This model is compatible with the lego system.
This is one of those annoying Lego pieces that had a limited run and only appeared in three sets around the turn of the millennium. It's hard to source because of its inherent scarcity, and most available pieces are both expensive and in…
This cover sits between the sink rim and the wall. Thanks to the gentle slope, splashed water runs back into the sink instead of collecting in the gap. The dimensions are designed around common Central European kitchen standards. The top…
The use case: There is an Exhauster in the bathroom that needs to be replaced. The old and new Exhauster brands differ so the existing holes do not align. The ceiling has a slope of 17 degrees and an opening for a (malformed) tube to…
This is a remix of gamble604's sloped top for BigTreeTech's TFT35 E3 v3.0 LCD screen from https://www.thingiverse.com/thing:4678675 to add an access hole for the USB connector on the TFT35 E3 v3.0 circuit board. I aligned the hole using…
Like thing:4694209 this is derived originally from thing:50249 . However, this version is appropriate for making molds, by allowing you to set a non-zero angle for the side walls. You set the thickness of the base, and the draft angle of…
I printed it using PETG, but it is untested how model solvents will affect PETG. Paint palettes used are made by GSI Creos, a brand commonly available in Japan. This design tilts at 5 degrees.
Can be advantageously printed out many single parts and then glued together in the desired shape, or print ready for 5. it is possible to build as you wish, only the imagination sets limits. Feel free to share your particular solution.…
Update: When I uploaded the files I was tired and accidentally took an earlier version that didn't match the images, now everything is correct, sorry about this. I will be happy if you share your Make. Recommendation. Parameters: 3…
BOM: Glue Minimum 4 pcs. ⌀6x3 Neo Magnet and more depend how many part you want connect. I will be happy if you share your Make and give me a Like. Recommendation. Parameters: 3 Layers: 4/3 (TOP/BOTTOM) Infill: Not needed Layer height: 0.2
I like the NetKissa design, but I also wanted to be able to easily slide pieces out of the trays and I thought the sloping sides of the Jark3D trays was a reasonable solution for that. I imported NetKissa's .stl file into Fusion360,…
This model is compatible with the lego system.
Duplo brick generator which makes sloped roofs with nice round tiles. Does not exactly copy any genuine Duplo brick (as you can see the blue one on photos) but it fits and it's similar in feel. There several pregenerated STL files: 4x4x2…
09/12/23 update, found an issue with the bottom mold part and the indents not being high enough, file replaced A mold for a scale lock block because at 1/10 they just aren't practical to print This is a 2 part mold with significant…
Tray with segments, where a sloped edge helps you pick out small things like screws. I made versions for 1cm, 2cm and 3cm height. I made different configurations like 2x2, 4x4, etc. Tips: You want a slippery slope. PETG Not too high layer…
Gridfinity bin for loose tools with a rounded bottom. Bin fits in a 2x5 gridfinity footprint and is 10U tall. Bottom of bin is rounded to allow for easier retrieval of tools. The black model in the photos was printed with Polymaker…
K1 Max sloped shims for leveling the print bed Category: 3D Printing
