Counting matching models…
I had an Anker PowerWave wireless charger A2503 lying around that I didn't need. That's why I developed this phone holder for my BMW F11 and Samsung S20 Plus in a Spigen Tough Armor case. I like the inductive charging. So the wireless…
This is a kickstand to fit a Spigen phone case for a Samsung S21FE. I am not sure if there are other models it will fit. I don't believe the kickstand is compatible between all the Spigen cases. I have included a fully parametric Fusion…
works great on my iphone 14 pro spigen case, and might work on others too, most likely cases made around the same time. print on highest quality, normal supports, and it's recommended to use adhesion. it is not recommended to eat the…
I recently purchase the Google Pixel 6 to replace my aging OnePlus phone. I had the Spigen wireless charger my wife used to charge her phone. I designed a new stand to hold the wireless charger for my Pixel 6. This might work for other…
This is a redesign of my original Note 20 Ultra phone holder with a tough armor spigen case to accomodate my new phone the Samsung S22 ultra with the same case. I have made the design with a lower height and overall smaller frame. For my…
I designed this for my right hand drive F10/F11 to hold and charge my Note 20 Ultra with a spigen case. Added off-centre ones because they come very close to the centre console trim also added an off-centre LHD version Uploaded a shorter…
I got AI to make a new design for the battery door, allowing straps to be attached. I sized it to perfectly fit the Spigen straps, and when using my other model for loop keys, it works perfectly, and is super comfortable. Without Spigen…
There wasn't an M-Series mount or case for the Pixel 8, so I spent a few hours designing this from scratch. All I had was a small ruler, so it was a lot of trial and error. Note: From my testing, sunlight shines through or reflects off…
I got tired of plugging my phone in every time I got in my car so I made this mount. The base fits in to the change bin on the console; I used some friction tape to keep it in place. The stem is screwed in to the top of the base with a…
Here is the Phone Mount i made for my motorcycle. This holder is a exact fit for a Samsung 9+ with a Spigen Case Thin Fit ( https://www.spigen.com/products/galaxy-s9-plus-case-thin-fit?variant=570798145537 ) The phone slides in from one…
Print w/ supports and in dark or black filament because white will have lens flare from the sun or other bright sources of light. The inside slots might need some light sanding if the lens is too tight. I'm not sure if my lens is…
Phone stand that incorporates the 15W Spigen wireless charger. Should fit most Android & Apple phones. I already owned this Spigen 15W wireless charger:…
This is a second version of iPhone 12 Pro Max holder for 52mm photo filter. Meant to be applied on top of a cover (in this case Spigen Liquid Air, but it could work with others too). Version without any case is here Print both in 0.2mm…
My original backplate on on my spigen slim armour case is a bit worn so I made a new one. I have printed several test prints and iterations and found that best results was when it was printed face down on bed with supports. Print…
A narrower version of the controller key created by @ChadHendrixs_5476252. The loop is now 13mm wide, intended to fit the Spigen hand strap kit.
This is my Remix to get the spigen Rugged Armor PERFECT FIT on the dock. I dont plan to do a “tool free version” , cause I feel you need the m3 screws to adjust preassure and get all firm and secure to the original Dock. From original…
Edit: Added a version w/ a slot instead of a 'hole punch' for the cameras. It should make it easier to remove from the base w/o needing to push up from the bottom. This fits the Spigen Tough Armor encased OnePlus8 Pro. OtterBox hasn't…
Spigen's Steam Frame controller silicone grips block some of the controllers' IR tracking LEDs and they can't be freed up without extensive modifications. This replacement Battery door cover allows you to attach straps harvested from the…
I wanted to be able to have my phone standing on the bedside table. So I modeled this model in order to be able to insert a wireless charger from spigen https://amzn.eu/d/fVVJL49 I recommend printing it in PETG so as not to have a problem…
This Wireless Charger Stand/Dock is a precisely designed 3D model tailored to fit Spigen and other chargers with a diameter of up to 100mm. It offers a secure, stable platform for your wireless charger, with integrated cable management to…
Since I didn't want to open the cover every time I wanted to use the flashlight, I constructed a compatible sliding cover. To avoid accumulation of dust, however, I did not want a hole at the location of the flashlight. The flashlight is…
support kangoo iphone X/XS avec coque spigen core armor (ref 063CS24941) 2 parties : une à fixer sur la grille d'aération milieu/droite du kangoo (impression avec supports) l'autre qui maintient l'iphone X/XS avec coque spigen armor…
The presented model is a modification of the Spigen Gearlock system. The solution shown is fully compatible with the mechanism used in this system. Depending on the variant of the mechanism you have, printing an additional Mechanism…
A wireless charging cradle to ensure that your phone is always centered correctly - no putting it in the wrong place while half asleep and waking up to a discharged phone! Designed and tested for the Pixel 6 pro with the Spigen case using…
Built to allow users to have removable kickstand while also having wrist straps for drop prevention.
This dock includes routing for a charger cable, lines it up correctly, holds it in place, just put your phone in there and its good to go! Must have a Samsung S21 Ultra and the Spigen Tough Armor case for this to work correctly. Have been…
Found this nifty USB-C thermal camera dongle (TC001) on Amazon recently. My phone case prevents it from plugging in so I had to get an extender. I didn't like the huge gap that was left between the phone and the dongle which could lead to…
Uchwyt do iPhone 16 PRO w pokrowcu SPIGEN, ale pasuje także z wieloma innymi. Przystosowany do ładowarki MagSafe. Otwory poniżej ładowarki umożliwiają połączenie z wieloma akcesoriami brodit lub projektami dostępnymi w wyszukiwarce.…
This is a custom fit tripod clamp for an LG G7 ThinQ phone with a Spigen case. Would probably work for others but it fits this one very well. No overhang on the screen and very secure, and in the middle of the phone it only blocks the…
Fits Android Galaxy Note 20 Ultra with Spigen case. For mounting Mysondy Go box to phone. Glue the top clip in place. Fits my MySonde GO case: https://www.printables.com/model/922591-mysondy-go-case I made this to mount my MySondy GO box…
Made set of clips for the Vision Pro using the Spigen DR200 Adjustable Head Strap Compatible with Meta Quest Pro. Ive found that the padded head strap is quite comfortable and I was seeing some people buying it for the AVP and using…
I wanted my phone next to where I sleep. I don't have a night stand on my side of the bed, I have the side of a dresser so that is where this goes. Part is designed for a very specific use case: Pixel 7a Phone Spigen liquid air case Ikea…
Modeled in Tinkercad Sliced in Prusa Slicer 0.4mm nozzle SPEED profile PETG
Update 25-09-2025: V2 version uploaded. This model provides a larger adhesive surface, allowing more double-sided tape to be used to prevent sagging under the weight of the phone. This mounting plate is made to fit on the back of the…
Replacement kickstand for the Spigen iPhone Case (iPhone 14 Pro Max) but it might work for other Spigen case models. The little hinge tabs need a tiny amount of support from the build plate.
I have no idea if Spigen has a patent around the kickstand. I made this replacement because they do not offer replacement kickstands for their Fold 5 case and figure maybe some others would need it. I printed it with 100% infill at .12mm…
Remix of the original optimized for usability with the Pixel 7: Created a cut-out at the bottom, so one can swipe up on the screen while the phone is in the cradle in portrait mode. This wasn't possible with original model. Created some…
Print from PETG, with 100% infill and a few more perimeters. There are two versions of model here: standard Gopro quick release with added 2 pads on the Gopro quick release side to stiffen the joint and remove the clearance, so the camera…
After remixing https://www.thingiverse.com/thing:1991137 into this: https://www.thingiverse.com/thing:2748380 I got rid of my Pixel 2. I bought a Oneplus 5T and I needed a new stand so remixed it again. As with the pixel 2 I bought a…
Gridfinity 2x1x4 Bin for Nothing Ear (2) with Spigen Case https://www.spigen.com/products/nothing-ear-series-case-ultra-hybrid
Kickstand replacement for Spigen Pixel 8 case, remixed from Tyler's model. I found that printing it flat on the back created the best end result. Hole is tight but perfectly fits the original 1.5mm pin that came with the case without it…
This is a remix/custom of "Oneplus 5 dock" for my personal need in first time with my OnePlus 5T & Spigen Rugged Armor (K05CS22712) . I want to thanks user r3gis3r for his work. You rock dude. If it help you or like this one, please,…
Black is the new pink. This is for a Samsung S23 Ultra phone and Spigen Liquid Air case ( 8809896740210 ). Possibly it would fit other cases having an oblong hole around the two small lenses. FreeCAD source model incuded ☺
Modeled in Tinkercad Sliced in Prusa Slicer 0.4mm nozzle SPEED profile PETG
Make sure to enable "detect thin walls"
Here is the Phone Mount i made for my motorcycle. This holder is a exact fit for a Samsung 9+ with a Spigen Case Thin Fit ( https://www.spigen.com/products/galaxy-s9-plus-case-thin-fit?variant=570798145537 ) The phone slides in from one…
There wasn't an M-Series mount or case for the Pixel 8, so I spent a few hours designing this from scratch. All I had was a small ruler, so it was a lot of trial and error. Note: From my testing, sunlight shines through or reflects off…
Modified the Apple Watch Stand by Aeonfly to fit my Apple Watch Series 8 with Spigen Rugged Case. Printed at 0.15mm layer height with auto generated organic supports.
Holder for Spigen Powerarc charger with cord wrap. Printed at 0.2m, 15% infill, and no supports required
Ive used PLA on a Flashforge Adventurer 5m Pro, but Its currently the winter here so Ill wait to see how it hold up in the Summer. If it doesn't hold up well in the cars interior in the summer, ill try my luck with ABS printing.
I fixed the broken legs of my Spigen S540W using a custom model, but things didn’t go well—it broke on the first use. I’ve now designed another model from scratch, and it seems okay for now.
Hi! I designed this to replace the standard plastic back for the Spigen Tough Armor A15 case because, I wanted a design on the back, and the original came off to hard when I go to clean my phone. This replacement stays on during normal…
I made this because I prefer cases with individual camera cutouts. It should be able to be pressed onto the cameras when the phone is in the case. It sits tight enough to not fall out. When using a 0.4mm nozzle, make sure to enable…
Make sure to enable "detect thin walls"
This is a model which should be used as a matrice for creating your own custom fitted holders for your phone. I am using the Spigen covers on all my phones since years and never had a broken phone since.
Adapter to mount Galaxy Z Fold 3 with Spigen Slim Armor case to Razer Kishi UPDATE: KISHI - Hand Grip V2 - This new version once mounted on KISHI will allow to fold KISHI. Check Photos. Older version still available to download. ----- On…
Nice snug fit for a Pixel 3 XL with Spigen Tough Armor case. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: .2 Infill: 20% Filament: Hatchbox PLA Black Category: Mobile Phone
This is a slide in mount for the Samsung S9+ with a Spigen Case Thing fit. You can stick/glue this holder to any other surface. You can add a mount at the bottom for a cable for charging. This is a cheap cable of AliExpress and has a 90…
I've been using the Nexus 5x variant I'm remixing from for about 6 months and upgraded my phone and needed a new stand. I added 1.8mm to the width and thinned the back by 1mm to accommodate for the case. The case I use is a Spigen rugged…
This is a minimal phone mount. I included the step file for the piece that goes onto your phone so you can modify it to fit your phone. In Cura, you may need to increase the size of all the piece to 1000%. I recommend sanding between the…
I tried some of the other kickstands on here and they wouldn't fit my case (too wide) so I made another one (The case is a Tough armour) The normal version clicks into place nicely, the short version stays in with just friction(mosty) I…
Neatly fits Spigen 120W [GaN III] 4-Port USB C Charging Station. Clips to 1.5in square tubing or equivalent.
I downloaded a couple I found online. They were all too big. I tried scaling them but it became clear that the plastic post requirement of 1mm was not going to be strong or render well. Then I realized that maybe this model was different.…
I really like the design of @ mmeidl78 but as I use the Spigen Rugged Armor for my Galaxy Watch 5 Pro, the charging disc was not aligned with the watch and it didn't charge. Remixing a mesh is not really one of my favorites so I build up…
I needed a dock to hold my deck when playing at the TV, but having a spigen case I had to remix one. As I was there I added a hex version of it, because hexes… (warning it takes a bit more filament than the standard version with 10%…
Spigen's Night Stand S352 is made for Samsung's Galaxy Watch 3 and its wireless charger. When changing to the Galaxy Watch 5 Pro, I noticed the charger got smaller and I designed this little ring to keep continuing the night stand.…
I have a flat area in my car to mount holders. (designed myself) With every new phone i design a new "universal" holder. Here is my holder for my Galaxy Z fold 2 with cable mount for charging. I have a case on it the Galaxy Z Fold 2 Case…
The phone slot is 82.3 x 13 mm, and the centre of the charging area is located 80mm from the bottom of the phone. This was designed for a Samsung S23 Ultra with a clear ‘spigen’ brand case, but will probably work fine with any similarly…
Disclaimer: Although I designed this from scratch, the originality of the design lies with Spigen. I saw similar model(s) uploaded to other model sharing platform and I assumed sharing this does not violate any copywrite law. In case it…
Bracket i've designed to glue the solar eclipse glasses's filter films onto a Spigen Tough Armor Case for pixel 8 Pro. It's not only usefull for the eclipse, you can actually use these filters to watch/film directly at the sun without…
This is a Samsung Galaxy S7 holder with the soft Spigen case. It should work with other models provided that the dimentions are ok... Width = 73.5mm height = 10.8 mm All the buttons remain accessible. Equiped with 4x5mm holes to be fixed…
This is a starter part to making attachments to a Galaxy Note 20 Ultra phone with a Spigen Tough Armor case. This clip fits snugly to the top of the phone and can be modified to add what ever device you want to attach to your phone. I…
