Counting matching models…
Make sure you push in the two triangles close to the short end of the command strip first and tilt down towards the long end to snap into place. Compatable with all the channel models that David D has created. If you have any issues…
Print approx. €0.30–€0.36 excl. taxPreliminary estimate for PETGSource material: PET
Needed a simple snap in zip tie element for holding up a power strip under my Desk using two modules per zip tie and it's almost impossible to remove the strip without cutting the ties Perfect for me
This is half of a cable spool, I use it for underware cable management on larger and heavier cables. I noticed that the hook in the main model was only available for 25mm multiboard, so I recreated and adapted. It's made in openscad so It…
OpenGrid Underware Zip Tie Snap Element modified for Lite Grid. I haven't actually had time to mount my grid and test it out, but some people on the original model asked for my modified version, so here it is! I printed a few of the…
just another cable tie clip for Multiboard/Underware. It allows for (hook-and-loop) cable ties up to 12 mm wide. The final result does not look as tidy as other Underware components but is a quick print and the cable ties allow for a…
This holder mechanically attaches to the multiboard using threaded screws (see https://www.printables.com/model/980088-multiboard-compatible-bolt-for-small-thread ) The caldigit generates significant heat, so there is a clearance between…
The original channels are great, but don’t lock in as securely as I’d like. Using them with the “Grip Channel Snap” is solid but can be tough to install/remove. This version flares the walls slightly for a more secure fit — easier to use…
Hang your headphones or other items under your desk using the Underware cable management system
The channel clips are designed to be used with Hands on Katie's Underware channels . The original channel base design works well but it was a lot of extra printing (channel base + the connector insert) compared to using this model. The…
Even though it goes against the entire design philosophy of the Underware organization system, sometimes a cable tie is still the right tool for the job. This takes up one slot on the multiboard and provides a set of loops to run a cable…
This is a holder design specifically for this KVM model (not affiliate) that you can buy from Amazon. Multiconnect is used for the connecting interface and it align with openGrid's 28mm grid size.
A mount for your 2018 Mac Mini to go under your desk as part of the Underware system. .2mm layer height, 15% infill, 3 wall loops, supports required. Printed example in PLA. You can use the plastic bolts from HERE to mount it to the…
This is an Underware mount for the CalDigit TS4, generated using Andy Levesque's Underware generator. I don't really claim any ownership of this, since I just put the dimensions into Andy's code and this is the file it produced. I've…
Added a simple hole to pass through cable ties, zip ties or thin velcro strips so they can be used as standalone cable anchor points.
This mount is designed to be used either with Underware, or multiboard, to mount your Unifi Flex Mini 2.5G Switch.
This is for attaching a HP 45W USB-C laptop charger to an openGrid board using multiconnect. Print one of each part, using the settings you used for the other components of your openGrid setup. This power adaptor is not very heavy. You…
This is a remix of an existing multiboard underware project to instead mount using openConnect to openGrid/underware. I've included mounts for the Lite version (which is what I use) but you could easily mount to the full version. I've…
A hybrid mount combining openGrid Lite screw-down stability with Underware channel-grip snap functionality
Printing: Print with PLA, print on funneled side, no supports needed. Consider adding a brim when using materials with build plate adhesion issues. Usage: I made these to guide cables below my Flexispot desk. 45 mm is enough for the…
An Underware ( https://handsonkatie.com/underware/ ) holder for my M-Audio midi keyboard compatible with the standard Underware connector. Can also be used with other light but large pieces of equipement Need to tuck away your large but…
Absurdly tight , and prints fast, 3 min per piece, saves material. (on my Creality K1C) Underware 2.0/Pipeware compatible. Do not print in PLA or any other brittle material. You won't need to use it under every tile, 2 per channel is more…
Another Underware/Multiboard under desk solution. This time to hold my HP G4 Dock and power brick.
Underware mount for Ugreen usb switch https://eu.ugreen.com/products/ugreen-usb-2-0-switch-2-in-4-output-usb-kvm-switch?_pos=7&_sid=d7dcb4fc2&_ss=r In slicer mirror it along x axis
Click connector plate for attaching power supply units or power strips to Multiboard with cable ties. (Matching the “Underware” cable management system from HandsOnKatie.)
A simple 5mm diameter clip for multiboard/underware. Use these bolts to attach to multiboard: https://www.printables.com/model/1026503-multiboard-compatible-bolt-with-knurled-head and…
If you like the model, please give a like 💟 and post your prints 📸. 💡 Underware - Multiboard - Quick Release Mount for Intel NUC 💡 💫 Recommendations PLA/PETG 0,2 mm layer no support
These connectors allow you to use the excellent kliptt cable holders https://www.printables.com/model/424351-klippt-locking-cable-clip with your multiboard.
This is a clip for an Adils leg from IKEA for use with the Underware cable management system. I basically just remixed an existing clip for the legs and slapped a “Small Thread” on it from multiboard.io. This will allow you to mount the…
Slides onto bottom rail of the socket. Tested with UK version, fits EU too.
If you like the model, please give a like 💟 and post your prints 📸. 💡 Underware - Multiboard - Lenovo 90W Power Adapter holder (ThinkPad Universal USB-C Dock) 💡 💫 Recommendations PLA/PETG 0,2 mm layer no support
If you like the model, please give a like 💟 and post your prints 📸. 💡 Underware - Multiboard - ThinkPad Universal USB-C Dock holder 💡 💫 Recommendations PLA/PETG 0,2 mm layer yes support - for the lip on the top that holds the dock in place
This is my collection of UNOFFICIAL extra height (6mm and 12mm extra) I, L, C, T, X channel tops for Underware by Hands on Katie. They are 100% compatible with original channel base parts. Parametric models You need a free Onshape account…
This mount is designed to be used either with Underware, or multiboard, to mount your Unifi Flex Mini 2.5G Switch.
This mount is designed to be used either with Underware, or multiboard, to mount your Unifi 1G Switch.
This is a mount for the 12-port Belkin power strip using the Underware system. This clips on to the power strip and uses the strip's mounting holes as in Trevor Harrison's original version. This version adds ample threaded attachment…
An underware ( https://handsonkatie.com/underware/ ) holder for the Fiio K3 DAC compatible with the standard underware connector. You can find the model on my onShape…
wall mount for BOBOVR battery charger. b2 charger version ( quest 2 / quest 3 / pico 4 ) for use on multiboard mounting solutions, using multiconnect attachment system- created using the generator provided in underware2.0. personally, I…
Thanks to the Underware 2.0 Customizer, I have adapted the mount for an AppleTV 4K. This sits well in the mount and can be securely attached under the desk.
Thanks to the Underware 2.0 Customizer, I have adapted the mount for an UGREEN Nexode 100W Desktop Charger.
This is a Underware/MultiBoard mount designed specifically for the Linseek DisplayPort Switcher. The switcher slides in easily from the side, giving you full access to the switcher button. The mount also features cutouts for easy…
A recreation from scratch of @Hasanen's Multiboard/Underware Koppla power strip brackets , but instead of using push fit Snaps it uses Big Thread screws. I found that due to the weight of the power strip and attached power bricks and…
Enlarged and modified version of @BobMcGlobus_870140 click connector plate for attaching power supply units or power strips to Multiboard with cable ties. (Matching the “Underware” cable management system from HandsOnKatie.) The original…
Description Multiboard Zip-Tie Mount System This 3D-printed piece is designed to work with the "Underware" / "Multiboard" system originally created by YouTuber Hands On Katie. Its purpose is to simplify mounting chargers, power strips,…
Thanks to the Underware 2.0 Customizer, I have adapted the mount for an FeinTech VAX01202.
Thanks to the Underware 2.0 Customizer, I have adapted the mount for an Sony AC-PW20.
This model solves the problem of the Standard Underware Connector where the connection to the multiboard is very strong (too strong, even) and the little thread that holds it breaks off very easily and holds weakly. This model orients the…
A I4 Channel based on the Underware project by Hand on Katie . Perfect to route in cables from the side when the multiword ist not mounted via screws but mounted with VHB tape.
Für das fantastische Cable Managment-System “Underware / Underware 2.0” von @HandsOnKatie_827995 habe ich hier mit dem Generator einen Item-Holder für die Steckdosenleiste von IKEA “ KOPPLA Mehrfachsteckdose 8-fach/Schalter, geerdet weiß,…
Nova Pro X controller mount for under desk. Compatible with multiboard / underware tiles and t-bolts.
Holder for the RB5009 to be used with Multiboard systems. Includes plate for POE Power Brick Created for the Underwear cable management system.
Two brackets to fix your Apple Mac Mini M4 to underware grids using standard multiconnect connectors Parts to print : left_bracket x1 right_bracket x1 big-thread-connector-for-multitool x8…
Remix of the original bracket to support the Multiboard with the ability to be swapped without removing the pegs. Requires a few supports, but the automatic supports should be enough.
designed as a low profile alternative for official snaps. fits velcro ties up to 12 mm wide
Added mounting holes for Underware / Multiboard snap connectors. Underware: https://handsonkatie.com/underware-2-0-the-made-to-measure-collection/
This is my remix of Universal Cable Holder by VC Design meshed with socket for multitool connector for use with Underware/Multiboard. I've also created additional 7 slot variant. To connect it to the board you need…
I got tired of having off-center and crooked predrill holes for installing the MultiBoard Core grids in my UnderWare (https://www.printables.com/model/941161-underware-the-ultimate-cable-management-solution) system, so I made this small…
To save some plastic and not print the base grid, just use screws to fix underware-compatible modular parts anywhere
This cable tie holder screws in the holes in the Underware cable channels. I made it to aid in installing bigger bundles of cables in the wider channels. It helps during the routing but also removes stress from the covers if you have…
UGREEN USB 3.0 4-Port Switch Underware holder compatible with Multiboard system. It was made by Underware 2.0 Customizer. Link: https://handsonkatie.com/underware-2-0-the-made-to-measure-collection/ Link to multiboard:…
T-Bolt driver designed to be easier on my hands than the small tool from the Underware 2.0 Connector's page. This one is wider to accomodate the wider t-bolts for use with the cable/zip tie straps. This was inspired by Product Design…
This is the openGrid adaption of the Underware system by Hands on Katie . The channels can be directly snapped onto the openGrid base board - the lite board version increases print speed and reduces filament usage. See my introduction…
This is a knob for holding your raspberry pi 4 case on the Multiboard/Underware cable managment system. you can choose if you want to hold you case by two or one knob, the designs for both cases are slightly different. you need a…
pretty self explaining. I made some versions which hold together much tighter (too tight), let me know if you prefer these, then I will upload those too
Does your joystick(s) take up so much space on your desk? With this model you can store them under your desk with the Multiboard system. It can be adapted to any joystick, the parametric files are included below. the current STL version…
Overview This is a collection of connectors to hook items from the Underware cable organizing system to GOEWS boards. This first set is for the larger Multiconnect based items. (these versions were done from scratch, and actually from…
Underware mounting for OWC 11-Port Thunderbolt Dock (Thunderbolt 4, OWCTB4DOCK). I made it to put there the dock with its rubber feet, so you don't have to remove them.
Mount your Lenovo ThinkPad Universal Thunderbolt 4 Dock to MultiBoard/Underware using Multiconnect Connectors! This model is uses the existing screw mounting holes and the inset edges in the Dock to lock the print to the Dock. It uses a…
A form fitting underware/multiboard mount for the AV Access Dual 4K Monitor KVM designed to use less filament and have plenty of ventilation. Includes removable rear slide in pieces to keep it securely in place. You don't have to use…
As I found most of the existing mounting options a bit overkill and could get away with rather small screws for mounting the multiboard under a desk, I came up with this little grommet that screws into the thread of the multiboard and…
As I like to keep it simple, I came up with these small clips to complete the Underware under my desk. Printing with three perimeters should provide extra strength. I also uploaded the Fusion 360 file so you can play around with it. There…
Screw clamp to fix a cable to a Multiboard/Underware and to provide strain relief. I use this clamp to fix cables that are threaded trough a cable grommet in my desk so they are not pulled out of their clips or sockets. I recommend…
Sometimes you inevitable do need a cable tie in your cable management. This quick and easy print allows up to 12mm velcro ties to be mounted on your multiboard.
I don't really claim any ownership of this, I just put the right measurements into Andy Levesque's Underware Generator and it spat out this model. I've marked this as CC-NC-SA to match the original license of Andy's OpenSCAD code. It's…
Simple remix of the model by @ bigalex , with the distance of the holes changed to fit the OpenGrid system instead of Multiboard. Use the openGrid Underware Base Compatibility Snap from the Underware for openGrid - Manage your cables…
Underware mount for Uplift Desk keypad. Fits model JCHT35K2. Use 2x M4 socket head screws, nuts, and washers to attach the backplate to the keypad. Use 2x Multiconnect connectors to attach the plate to the under desk multiboard.
note: right side of Xbox pumps out some serious heat. Use a heat resistant filament for both the mount and t-bolts; possibly the multiboard panel as well if you don't have good under desk airflow. PLA will not survive; you've been warned.…
Underware 2.0 uses low-profile 1mm hex screws (among other fasteners). They're kind of fiddly to get started, and they're too short to hold in a regular 11mm socket. So I designed this hand wrench specifically for these screws. It's…
These have the same screw recess for mounting as Underware channels set up for “direct multiboard screw” mounting. Having individual/separate hooks allows for varying the spacing to accommodate the specific amount of excess cable and how…
While I strongly preferred “direct multiboard screw” mounting for Underware components, I really didn't like dealing with the flat bolts and corresponding finger tool that were included with those components. Here is a similar tool to the…
This mount is designed to hold 2 double sockets and a USB module of IKEA Askvader system. it's separated in four parts for easier printing. Print on the side with the opening facing upwards. The parts have holes for the openGrid board…
This is a custom Underware (Multiboard) holder for the HP G5 USB C Dock Station It uses Multiconnect v2 slots (with the snap instead of the dimple) as its mounting points. Optimized for filament use, it's made as a clam shell that…
This is a wall control pegboard bracket that connects with the underware cable channel tops. It's recommended to print in the orientation pictured below, with supports, and a brim.
I made two versions of the tunnel. One following the curve of an “S” and one that is inverted.
Fixture for mounting SDRPlay's RSP2 with Multiboard or Underware organization systems.
A remix of the Channel Grip Snap to allow mounting led strips inside the snap
Wydrukowałeś mój model? Zachęcam do podzielenia się wrażeniami/zdjęciami na jego temat w zakładce realizacje/komentarze :) Każda opinia motywuje mnie do dalszego działania ;) Dziękuję :) Może komuś przyda się mocowanie do przedłużacza…
Wydrukowałeś mój model? Zachęcam do podzielenia się wrażeniami/zdjęciami na jego temat w zakładce realizacje/komentarze :) Każda opinia motywuje mnie do dalszego działania ;) Dziękuję :) Jako że zacząłem budowę organizacji kabli pod…
Wydrukowałeś mój model? Zachęcam do podzielenia się wrażeniami/zdjęciami na jego temat w zakładce realizacje/komentarze :) Każda opinia motywuje mnie do dalszego działania ;) Dziękuję :) Model zaprojektowany, lecz jeszcze nie został…
Wydrukowałeś mój model? Zachęcam do podzielenia się wrażeniami/zdjęciami na jego temat w zakładce realizacje/komentarze :) Każda opinia motywuje mnie do dalszego działania ;) Dziękuję :) Model zaprojektowany, lecz jeszcze nie został…
Underware-compatible mount for a Raspberry Pi 3B+ in the case. I didn't feel like taking the Pi out of the case, so I drew up a mount that would incorporate it. Extra holes on the bottom to provide for airflow and minimal walls so that…
I printed mine in 0.2mm, no supports with the orientation the model comes in. Thanks to Krutoo for doing most of the work for the 90W adapter!
Holder for Palmer DI-Boxes, based on David D's multiconnect holder. Compatible with David D's awesome openGrid ecosystem: https://www.printables.com/model/1214361-opengrid-walldesk-mounting-framework-and-ecosystem Can be used together…
This remix came about when I needed to route a bunch cables from my wall-mounted grid to devices sitting on a shelf in front of it. Because of the small clearance between the shelf and the bottom row of the grid, I could not use the…
A rounded holder for the ICY BOX dock, model IB-DK4034-CPD , which keeps all ports easily accessible. I have it attached to an Underware openGrid under my desk to have a single cable to connect to my laptop. The top mount is compatible…
Supports to hold the Logi Dock power supply with the underware, Opengrid and Multiconnect systems Contains both parts, which are not exactly symmetrical, to cope with the 28mm spacing of the Opengrid system. Be careful to print both parts…
A holder for a charger. You've seen the title. I recommend using single piece snaps . Also openGrid "full" since this charger is an absolute unit.
The holder is designed for extension cords with multiple outlets. It is designed for outlets used in Central Europe. The design is based on the dimensions of the manufacturer EMOS. The two-piece holder is supplemented with 4 pieces of…
This is for attaching a HP 45W USB-C laptop charger to an openGrid board using multiconnect. Print one of each part, using the settings you used for the other components of your openGrid setup. This power adaptor is not very heavy. You…
