Counting matching models…
This is a battery bracket for RAK Unify 150x100x45 enclosure plate . It allows you to fit 3 cell 18650 battery packs like the Adafruit 6600mAh 18650 pack . Print settings I used on my MK4 with 0.4mm nozzle: Print in PETG or ASA if using…
A 10 inch rackmount for unify clout gateway ultra particularly stable Flat base on the front of the housing Integrated space for housing feet Precise fitting of the housing Clips to prevent it from being pushed out Printing possible…
Unifi Switch Lite 8 port POE based on remix of Unifi Flex XG power Brick wall mount by RockNLol I just resized model to adapt to power brick of the switch (115% bigger)
A simple mounting plate for a WisBlock Base (RAK19007) inside a Unify Enclosure. Fusion 360 File included. Category: Electronics
This is a remix of Szymon's excellent model. All I did was make it one piece, since it will take the USB plug diagonally and you can just push it in then. No screws necessary.
A remix of my prior USB receiver attachment with wider holes allowing for a narrower metal loop.
Who ever disassembled these antennas knows it's a problem. So I created this practical gadget, it saves a lot of time and nerves :-). For remixing you can use TinkerCAD source: https://www.tinkercad.com/things/75DUwfTVZUt Print…
I designed it in Fusion360. You can render your own STL with custom spacing. Open Sketch 1 as seen in the screenshots and edit the spacing. Everything else will be calculated and rendered automatically! Have fun and upload photos if you…
I added a thicker bottom / back, widened the clippy bit and put a bigger circle on it and placed a hole in it for a keyring to go through it the keyring helps act as a stop to prevent the dongle slipping out, also any movement / swinging…
I had a mishap when I went to replace the antenna on my Meteor65 pro 2022 version whoop. So I had to replace the VTx, and decided to use a unify pro32 nano. Here's the mount I made for it. It works much better than what I did before……
This is a simple framework expansion card adapter for the newer Logitech Unifying receiver. Print vertically in two pieces with minimal infill – 0.20 mm layer and 15% should work just fine. You will need: - A USB-C to USB-A slim adapter…
If you purchased any RAK Unify enclosures, such as the RAK Wismesh Solar Repeater Mini for Meshtastic, you'll need some mounting brackets. The default kit doesn't include them, so I've made some based on RAK's own design documents. They…
RAK has a Unify enclosure with screw sites on the back. This tab lets you screw it to a flat surface. I used 12mm M3 allen heads, but perhaps an improvement would be to use flathead screws and modify the holes so the heads are flush.…
Includes: Rear Hatch with a slot for the TBS Unify Pro32 HV and an MMCX 90 degree Antenna, such as the Foxeer Lollipop 20x20 M3 glue- (or velcro-)on stack mount (I use a Matek H743-mini V3) 14mm camera canopy (tested with the Caddx Ant)…
LOGITECH UNIFYING RECEIVER PROTECTION BOX since it does come without any Category: Computer
To mount a RAK Unify Enclosure IP67 150x100x45mm with these magnets: https://www.amazon.com/dp/B0CQ2G6N2Z?ref_=ppx_hzsea You can add a N-type antenna. I use a low profile TE Connectivity Antenna
Remixed @pdxlocs to allow for a battery to be placed underneath
This rack was made for anyone with Ubiquiti Unifi gear that wants a little rack to tuck into their utility room. It's made specifically the models listed below, but could be easily adapted for other models/configurations. Is it perfect?…
Mit diesem Gehäuse befestige ich meine Unify Flex Mini auf einem Lochblechzwischenboden in meinem Netzwerkschrank
Mount pattern 25.5mm. TPU printing, no supports needed
I wanted to mount SMA antennas to my quad, so I designed a holder/mount for the TBS unify SMA to mmcx pigtail. The distance between the holes is 25 mm and they are designed for m3 screws. Doesn't realy need supports, 15% infill is fine…
Da ich meinen USW Flex mini an die Wand hängen musste und keinen Wandhalter hierfür hatte, habe ich mir einen gedruckt, bzw. im Endeffekt sind daraus 3 Versionen geworden. Die Wandhalter sind alle 3 so ausgeführt, das es innen kleine…
This is a mounting plate for a SolarXiao inside a Rak Unify 150x100x45 Enclosure . The PCB mounts to the plate with M2.5 x 5mm screws and the plate mounts flush to the enclosure standoffs with M3x5mm screws. The area underneath the…
Incase it is required to maintain some distance between the wall/ceiling and the backplane of the UNIFY AP Pro (e.g. for Keystone adapter) then you can use this distance enclosure. Current design uses Ruthex melt-in threads, but - as I…
This bracket allows mounting the G4 door bell camera with an angle that can be adjusted (in Fusion 360) to required degrees in both vertical (top/down) and horizontal (left/right) direction. The included stl mounts camera looking 35…
Spacer mount for TBS Unify antenna and XT-60 plug Print instructions Rotate it by 90° to stand vertically, before printing
Weighs 0.26g Printed at ultra detail took 7mins. Added a tab to heat shrink the VTX's antenna to. I glued the edges of the TBS Unify PRO32 nano VTX to the frame with e6000 and let it dry over night. Pictured is the frame next to the…
BOM 4x ~8mm M3 screws, cap head or pan head. Zip ties to mount to pole. I modeled this for the harbor freight 3/16" width zip ties. Notes Designed for the 150x100x50mm enclosure, but I believe the hole pattern is relatively universal!…
About I'm calling this the RAKshare. A bracket for the RAK Unify 180x130x60mm enclosure to mount: RAK 1W booster 19007 / 3401 / 13302 board. Waveshare Solar Power Manager (D). Adafruit INA3221 STEMMA QT board for power monitoring.…
Off center mount for a TBS Unifiy Pro HV
Required Materials 2 x 2.5mm Nylon Cable Ties
I didn't want to order seperate 25mm M2 screws + extra spacers to place the new TBS mounting board ontop of the stack so I created a custom mounting plate which replaces the one for the stock Runcam VTX on my Diatone GT-R349. I used 4mm…
Print this part, if you are using an Ikea IVAR printing rack and want to use the nice mount from @Scotthon_200246. Print the other needed parts from the original make:…
This is a mounting accessory for the RAKwireless Unify Enclosures . There are already a lot of mounting options, but for my specific use case I needed an easy way to plug the enclosure on a 1x2" rectangular pipe. The mounting accessory is…
Modified to fit TBS UNIFY PRO 5G8 HV VTX. Check this it you need complete Chameleon Ti rear end: https://www.thingiverse.com/thing:3654907 Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2…
This is a mount for Team Blacksheep's Crossfire Immortal T antenna and Unify Pro SMA pigtail. Print in TPU with about 15% infill and supporta enabled. Mount the Immortal T in the TPU piece before mount everything to the frame. This thing…
I image a lot of machines, then ship them out. This clip allows me to attach a keyring to the USB so I never again forget to remove it.
TBS Unify Pro32 DP or HV VTX mount designed to fit in front of the Heewing T1 ranger. My goal was to have the antenna in line with the borders of the front air inlet. You need to cut out the foam inside the air inlet to get a better air…
This Object lets you mount the TBS Unify antenna (and your RX antennas) on your Lumenier QAV-Skitzo Dark Matter. Printed in TPU (NinjaFlex) for maximum durability and also to protect the antenna on impact due to the flexibility. Other…
This is a mounting accessory for the RAKwireless Unify Enclosures. There are already a lot of mounting options, but for my specific use case I needed an easy way to clip the enclosure on a vertical 100 mm pole in a 45 degree angle. The…
Wisblock Unify case mounting ears. I've attached the referenced roundedcube.scad file from https://gist.github.com/groovenectar/92174cb1c98c1089347e - I am not the original author.
General purpose case for TBS Unify Pro 5G8 HV VTX. Designed for mounting on DFRobot Devastator robotics kit, but could be used for other purposes. I used 4 x M3x16 screws and 4 x M3 nuts, but would recommend using M3x18 screws or longer.…
A simple case to mount the TBS Unify Pro32 HV flush with the Wing surface. I used it to mount the VTX in a Mini Talon wing but other Wings would work too. The lid has a little cutout so that a little heatsink can get in the direct airflow…
I printed this with ASA as well as ABS-CF at 50% fill. To mount a RAK Unify Enclosure IP67 150x100x45mm with these magnets: https://www.amazon.com/dp/B0CQ2G6N2Z?ref_=ppx_hzsea
This is a mounting accessory for the RAKwireless Unify Enclosures. There are already a lot of mounting options, but for my specific use case I needed an easy way to clip the enclosure on a vertical 100 mm pole in a 45 degree angle. The…
I made a three-piece design to snuggly accommodate R9MM, TBS Unify Pro HV and ImmortalT antenna in the back of Armattan Chameleon Ti 5". Print layed as on pictures, ImmortalT requires support from the bed only; TBS Unify & R9MM mount with…
TBS Unify and Crossfire Holder printed with saintsmart tpu. Needs supports Category: R/C Vehicles
Sized for the Makerfocus 3000mah pack but probably fits others of the same spec Sized for PLA Uses the screws included with the enclosure/plate kit Antenna slots are sized for the included bluetooth with the adhesive strip and paper intact
This is just a remix of a camera support I found for the front side of the Elegoo Centauri Carbon. I made it compatible with the Unify G3 Instant cameras, and can be used with either the front door opened or closed. Also you can still use…
Rcexplorer Tricopter V4 TBS Unify Antenna mount Category: R/C Vehicles
This model is a lid for the RAKwireless Unify Enclosure 100x75x34mm with support for the TFT touchscreen RAK14014. It requires support during printing. To fix the lid to the enclosure, 4 pieces of inserts are required with M3x4 mm thread,…
Sometimes I receive inquiries for an outdoor enclosure for the RAKwireless WisTrio RAK5010 cellular location tracker. A RAKwireless Unify Enclosure 100 x 75 x 38 mm with or without solar panel is sufficient to carry the RAK5010 and a…
This is a TBS Unify antenna mount for Martian II (Alien Clone) quadcopters. Category: R/C Vehicles
Based off the closed hole 40deg Session mount version. Chopped some different holes for the location of a default install of the RaceFlight Revolt FC. Added a finger hole for VTX changes when it's sitting on top of the FC (TBS Unify).…
Install your Unify AP on celling without new holls. Just use one of halogen lamp fixture. Fast and secure. OpenSCAD model is fully customisable. Secure adapter in lamp fixture with 2 small screws. Monting plate from Unify AP secure with 4…
My computer is docked too far from my mouse for the Unifying receiver to get a reliable signal. This cap puts the receiver on a USB extension right at the desk surface, pointing at the mouse, without an extra dongle lying on the desk. It…
This is a mounting plate for a SolarXiao inside a Rak Unify 150x100x45 Enclosure . The PCB mounts to the plate with M2.5 x 5mm screws and the plate mounts flush to the enclosure standoffs with M3x5mm screws. The area underneath the…
Sized for the Makerfocus 3000mah pack but probably fits others of the same spec Sized for PLA Uses the screws included with the enclosure/plate kit Antenna slots are sized for the included bluetooth with the adhesive strip and paper intact
If you purchased any RAK Unify enclosures, such as the RAK Wismesh Solar Repeater Mini for Meshtastic, you'll need some mounting brackets. The default kit doesn't include them, so I've made some based on RAK's own design documents. They…
Install your Unify AP on celling without new holls. Just use one of halogen lamp fixture. Fast and secure. OpenSCAD model is fully customisable. Secure adapter in lamp fixture with 2 small screws. Monting plate from Unify AP secure with 4…
About I'm calling this the RAKshare. A bracket for the RAK Unify 180x130x60mm enclosure to mount: RAK 1W booster 19007 / 3401 / 13302 board. Waveshare Solar Power Manager (D). Adafruit INA3221 STEMMA QT board for power monitoring.…
This is just a remix of a camera support I found for the front side of the Elegoo Centauri Carbon. I made it compatible with the Unify G3 Instant cameras, and can be used with either the front door opened or closed. Also you can still use…
This is a mounting accessory for the RAKwireless Unify Enclosures . There are already a lot of mounting options, but for my specific use case I needed an easy way to clip the enclosure on a vertical 1x2" rectangular pipe. The mounting…
I image a lot of machines, then ship them out. This clip allows me to attach a keyring to the USB so I never again forget to remove it.
I printed this with ASA as well as ABS-CF at 50% fill. To mount a RAK Unify Enclosure IP67 150x100x45mm with these magnets: https://www.amazon.com/dp/B0CQ2G6N2Z?ref_=ppx_hzsea
This is a set of two flexible port covers designed specifically for the UnifyDrive UT2 Portable NAS. Perfect for protecting the device's ports during transportation, such as in a backpack, these covers provide a secure fit while being…
We wanted to attach these keyrings to USB receivers at work so they wouldn't get lost or forgotten. These attachments allow doing so without any adhesives or damaging the receiver.
TBS Unify Race and FrSky XSR dual mount. Print in TPU, no supports. Fits nicely on top of your FC stack New! R-XSR mount added Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0.2 Infill: solid…
My Unify US-8-150W didnt't fit my 10" Serverrack, so i designed my owm model for it with the PSU beeing externally placed and connected with an TX60 plug. For the heatsink i used 25x25x5mm heatsinks to keep the parts cool.…
This is a mounting accessory for the RAKwireless Unify Enclosures . There are already a lot of mounting options, but for my specific use case I needed an easy way to clip the enclosure on a vertical 1x2" rectangular pipe. The mounting…
A cool model of individual pieces which can snap on to each other and can remove desk clutter easily. It contains a bookshelf, a stationary holder, a phone stand, a monitor with draws and a shelf as well as an everything box which can…
I created a In-Ceiling trimless mount for an Unify Chime by utilizing the orginal locking mechanism of the device
This is a mounting accessory for the RAKwireless Unify Enclosures. There are already a lot of mounting options, but for my specific use case I needed an easy way to clip the enclosure on a vertical 1x2" rectangular pipe in a 45 degree…
This is a rear lid for the ZOHD Dart 250. It fits an FrSky R-XSR and a TBS Unify Pro HV Race 2 including the corresponding antennas. With the heatsink of the VTX in the airflow it should not be able to overheat.
I made those objects to upgrade my ZOHD Nano Talon with a iNav powered flight controller. There are three objects: FC mount which fits the Omnibus F4 Top plate for the TBS Unify antenna Bottom plate for the TBS Unify Print Settings…
Object to mount a Team Black Sheep Unify antenna on a Dalrc XR215(plus). Category: R/C Vehicles
Mini Talon Unify 2g4 holder (bolts on canopy part 52056 from itsqv.com) canopy http://www.itsqv.com/QVM/files/canopy/52056.STL Category: R/C Vehicles
This is a holder for the TBS Unify VTX pigtail. Just insert the pigtail and secure the holder to your frame with 2 cable ties. Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts: No Supports: No Resolution: 0.2mm Infill: 15%…
TPU antenna holder and protector designed to hold the TBS antenna Category: R/C Vehicles
I used this holder to place the Flex Mini switches from Ubiquiti behind my TV board.
i replaced my S4 DECT phone with a new SL6 the charger of the SL5/6 don't have mount for walls. it's just a stand. Just draw a wallmount and the charger is secured on the wall. i printed in PLA with .2 Layer hight. bigger shouldn't be an…
3 Versions of Universal Mount for TBS Unify Pro. Print Settings Rafts: No Supports: No Resolution: 0,2 Layer 0,4 Nozzle Infill: 30 Category: R/C Vehicles
I bought a Logitech MX Master and was dismayed that there was no on-device storage for the Unifying Receiver. Ultimately, I purchased a zipper case for the mouse and decided to make a holder for the receiver. This should be printed in TPU…
Simply attach the Unify mounting plate to this adapter with four screws and then suspend the entire system to your beam with a long zip tie. I used 40% infill to give the screws something to bite into, but I bet 20% would work well also.
my project to mount tbs UNIFY PRO on my drone with 20x20 sizes Print Settings Printer Brand: Creality Printer: Ender 3 **Rafts:** No Supports: Yes **Resolution:** 0.2 Infill: 25 **Filament:** F3D TPU Orange Category: R/C Vehicles
