Counting matching models…
These parts were inspired from a design by KeeganBuilds (YouTube). I modeled these parts in OpenSCAD to fit the components from a 2 kW diesel heater kit and have included the .SCAD files below so others can modify to fit heaters with…
This is meant to be a stationary node, not a portable handheld device. It features: compartment for up to 4x 18650 lithium-ion cells (long enough to accommodate protected cells) M2.5 mount points for RAK19007 or RAK19003 base board M2…
Weatherproof with printable seal. Use TPU for the seal to make it weatherproof. Can be used without seal also. Made for 20mm cable gland and 4x M4 screws for the lid. I used PETG without fan and without support
Customized nameplates for the Apache weatherproof protective cases from Harbor Freight or Strongway from Northern Tool. This is a replacement for the plastic piece located near the handle. Its angled edges make it easy to secure in place…
A weatherproof enclosure for mounting your Ring sensor outside in the elements. This is for the 2nd generation sensors. I printed mine in PTEG to be more durable when exposed to the sun. Use a piece of TPU filament for the seal. If you…
This is a weatherproof (or waterproof depending on the version) case for a RAK19003 based Meshtatic node. Since the RAK19003 includes a Li-ion charging circuit and solar panel input port, the cases have room for a 2000mAh Li-ion battery…
Webasto/Eberspacher heater hull air inlet grill for the 90mm pipe. A unit with 3mm thick face plate added Print Settings Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill: 0% Category: Sport & Outdoors
Video of this project working: This enclosure is intended to hold a PN532 NFC reader along with a Raspberry Pi Zero 2 W for the purpose of reading an Apple HomeKey to unlock or open a door. I'm running the software found here and…
This page and the models are a work in progress, I have some other versions of the models I'd like to add and there are some details I'd like to add to this page. To-Do List Add file name explanations Add BOMs for various versions Add…
This enclosure was built to house a Sensirion SPS30 (particulate matter sensor) and an Adafruit BME280 (temperature, humidity and barometric pressure sensor) for an outdoor weather station. The goal was to have an enclosure that could be…
I wanted to use a network cable joiner for my outdoor cameras I put together this Box measuring a 155x40x45mm with the proper Grommet, Gasket and Cover If you decide to print it this what you need: You will need to use sustainable outdoor…
Introducing the Rugged Hex Box: AquaShield I’ve combined my admiration for Whity’s Rugged Box design with my passion for hexagonal patterns to create a versatile weatherprove outdoor storage solution. Perfect for activities like sailing,…
Aqara Door and Window Sensor Weatherproof Enclosure - Use your Aqara sensors Outside This enclosure helps keep your sensor dry when using it outdoors. For a complete weatherproof kit—including the enclosure for the Magnet, spacers, and…
Originally designed to hand out to homeless people to hold valuables like ID, lighter, feminine products, etc that they want to keep close and dry. They have been a huge hit with a lot of the social workers around the city and I can't…
This is a Sony camera hot shoe cover, with an overhang to help prevent water getting into the flash contact pins. This should help stop the ‘This accessory is not supported’ message when the flash hot shoe pins get wet. The best way to…
So, yet another air tag holder for dog collars! What makes this one special and worth your time downloading? Well, for one, it is sized for large dog collars, up to 1.25" (32mm) in width. But most importantly, I made this with the primary…
I've been sealing the house from air leaks as trying to save money on heating. These are replicas of the foam ones I got as I ran out in the first room. To install an outlet gasket you simply unscrew the switch plate, place the gasket…
I bought these 44qt bins at Costco, though I also see them listed on Home Depot's website. Pic #2 shows the label on mine - I can't gurantee they use the same exact latch on every single unit. Printing instructions: Print files come…
Remix of the box I found on here. Printed using fuzzy skin and textured plate using Creality PETG in a K1 Max. See PDF I included for needed hardware and assembly instructions.
Carry your spare 21700 battery for the Nitecore P20iX with confidence using this custom-designed case. Built with precision, this case accommodates Nitecore NL2150HPi and NL2153HPi batteries securely, providing both protection and weather…
My GE Outdoor ZWave SmartSwitch recently ceased working and I had some sonoff basics lying around so started out to build a weatherproof case to use under my deck and control the lights around the pool. I originally planned to use an…
I wanted something to help seal the connection between my extension cords for Christmas lights and couldn't find anything to do it, so I designed this. Later I found these things which do the same thing, but you have to pay for them:…
Compact and durable Meshtastic/Meshcore node based on the RAK19003, a 33140 LiFePo battery, and an Adafruit solar charger. See parts list below. The gasket is intended to be made using 1.75mm TPU filament or using standard 0.070" oring…
Made by the excellent zx82net (https://www.printables.com/@zx82net_107245) but they haven't uploaded all their models yet. So consider this a placeholder :-) Fits four batteries, although the render shows only three. A rugged battery…
This is a small, weather-resistent enclosure to hold a NodeMCU. It has 2 openings for PG7 cable glands so you can pass poower in and WLED control out without letting water in. There are three files: NodeMCU_outdoor_enclosure_base This is…
There is one question that everyone who is running some kind of home automation, but who doesn't fancy streaming a view from their front door to some big server somewhere, is asking? Where are all the Zigbee doorbells at? After failing to…
Outdoor weatherproof outlet cover
Recommended Print Settings Material: ASA or PETG . Note: Avoid PLA, as it will warp or degrade when exposed to direct sunlight and outdoor temperatures. ASA is the gold standard for outdoor use due to its high UV resistance. Infill:…
A millitary-style weatherproof container, but longer.
Bought thins enclosure from Adafruit.com and needed a base plate/plane to mount components to. Print instructions Nothing special or complicated about this. Slice it, print it.
Skids for the ZMR250 frame including double motor protection. Just like user Judar (from the source file) I had problems with the moist ground and getting mud in my motors. The side panels will protect your motors from dirt and also…
This small case is meant for 2x AAA battery, so you can lug them around safely while in the woods or at the range. I initially designed this to carry around some spare batteries for my active hearing protection while at the range. Uses a…
I needed to extend a GFCI receptacle box for a weatherproof cover to fit. This extends the box by about 1". Be sure and seal the mounting surfaces appropriately to prevent water intrusion.
only insert the protection in the audio-set station. Das Teil wird eingesteckt/aufgelegt.
I made myself corner water diverter as because of poor design current water divert does not keep all water away from wooden base, especially in corners, wood under does not like to be wet! Can be glued in place using silicone or montage…
Outdoor weatherproof outlet cover V2
We had a few of the latches go missing from these bins we purchased at Costco: https://www.costco.com/iris-44-quart-weatherpro-seal-storage-bin%2c-4-pack.product.4000226160.html Printed in PETG @ 0.2mm layer height. You will need to…
The fingerprint reader on my Ultraloq U-Bolt Pro stop responding, and I suspect it succumbed to the repeated direct sunlight and rain. Support was nice enough to send me a new fingerprint reader even though it was outside of their (too…
BASETech is a common remote sensor for weather stations. They are sold as Basetech WS-9130-IT, TFA Dostmann 30.3147.IT, Techno Line TX 35-IT and more brands. Although it should be able to survive on its own, a casing might prevent…
Some of the screws were broken in my weatherproof box. I designed this as a replacement part. I printed mine using PET-G, in a horizontal orientation and with the screwdriver slot vertical so that the stresses wouldn't cause it to…
Overview This internal mount plate is specifically designed to fit the bottom of a common 150x100x70mm weatherproof project box. It provides a secure, elevated platform for mounting microcontrollers, sensors, relays, or battery packs…
Особенности модели: Материал: Имитация натурального дерева с текстурой, создающей уютную атмосферу Форма: Треугольная конструкция с открытой верхней частью для легкого доступа к корму Дренажная система: Специально разработанные отверстия…
This cover slides in from the front (assuming you mount the unit with screws on a vertical surface), covering the USB plugs and leaving room for the switch. There is a small dot on the side to engage the plugs' ground hole to lock it in…
This rugged ointment container was developed by our nonprofit to help clinics in underserved communities distribute ointments in containers that can withstand harsh environmental conditions. When printed correctly, it provides a highly…
Allows me to mount Iphone 6 in topeak weatherproof case on any go pro mount for filming cycle rides in 240 frame HD makes go pro look second best. Make sure you remove supports particularly tiny piece between mounts. Instructions Created…
This is the feet I've created to snap into the Monoprice Weatherproof/Shockproof Hard Case (6.6 liters version - not sure about other sizes).
Our clip broke off on the corner so I decided to make a replacement. The clip is not a perfect 1:1 copy of the original, but it works well enough to get the job done. You may notice that the fit is tighter, if you have issues installing…
Please select a filament suitable for outdoor use and strong enough to withstand the forces required when locking the socket. I printed this in PETG-CF, the result was very robust, the final print was then coated with clear lacquer to…
uses a 130 motor. the model 5TT in the background is coming soon!!! if there are problems or somethings off or if you want a mini siren that no one has made yet let me know I will be happy to help !!!
Modern Outdoor Push Button Cover This cover was designed as an additional weather shield for a wall-mounted outdoor push button. The extended roof helps protect the button from direct rain, dirt, snow, and strong sunlight while still…
Designed an OEM Replacement Cover for a Low Profile Weatherproof InBox For Retrofit Siding Construction. I printed mine out of PCTG and cover is in durability testing in an extremely sunny location. Testing began 7/28/2026. It can be…
Der Teil dient als Schutz eines Temperatur Aussenfühlers vor Regen und Sonne. Zusätzlich lässt sich die Aussentemperatur leichter ablesen. Er kann einfach angeschraubt, oder auf ein Blech genietet werden. This part protects an outdoor…
A wall-mounted outdoor enclosure for small electronics that keeps rain out by geometry alone: no gasket, no O-ring, no silicone. Two printed parts, body and lid, printed in ASA. I use it for a 24 V → 12 V DC-DC converter (DFRobot DFR0205)…
Compact and durable Meshtastic/Meshcore node based on the RAK19003, a 33140 LiFePo battery, and an Adafruit solar charger. See parts list below. The gasket is intended to be made using 1.75mm TPU filament or using standard 0.070" oring…
Особенности модели: Материал: Имитация натурального дерева с текстурой, создающей уютную атмосферу Форма: Треугольная конструкция с открытой верхней частью для легкого доступа к корму Дренажная система: Специально разработанные отверстия…
RAK19007 Weatherproof Meshtastic Node Case A rugged and compact weatherproof (not submersible) case designed specifically for the RAK19007 WisBlock board. This design features a highly organized internal carrier frame and custom TPU…
Please select a filament suitable for outdoor use and strong enough to withstand the forces required when locking the socket. I printed this in PETG-CF, the result was very robust, the final print was then coated with clear lacquer to…
I made myself corner water diverter as because of poor design current water divert does not keep all water away from wooden base, especially in corners, wood under does not like to be wet! Can be glued in place using silicone or montage…
RAK19007 Weatherproof Meshtastic Node Case A rugged and compact weatherproof (not submersible) case designed specifically for the RAK19007 WisBlock board. This design features a highly organized internal carrier frame and custom TPU…
