Universal Power Strip Wall Mount / Under-Desk Clamps (3mm Screw)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Clear your desk space and mount any standard power strip securely to walls, desks, or furniture!
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 26
- Wydruki
- 0
- Wyświetlenia
- 122
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other House Equipment
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This clean and minimalistic design consists of two end clamps that slide onto each side of a standard power strip. By securing the ends instead of the middle, it provides a rock-solid hold that won't flex or wobble when you plug or unplug heavy adapters.
🛠 Hardware Required
Screws: 4x Self-tapping screws (3mm diameter, 2 for each side piece).
📐 Print Settings
This model is designed to be highly functional and extremely easy to print. No supports required!
Supports: No (Print flat on its base).
Material: PLA, PETG, or ABS/ASA (PETG recommended if it's going to hold heavy power bricks or be under constant tension).
Layer Height: 0.20mm - 0.24mm (standard settings work perfectly).
Infill: 20% - 30% (Grid or Gyroid).
Perimeters (Walls): 3 or 4 (Crucial to give the screw holes enough strength to resist the clamping force).
💡 Installation Instructions
Slide the two printed pieces onto both ends of your power strip.
Hold the power strip against the surface (wall, under-desk, or cabinet) where you want to mount it.
Mark the screw holes with a pencil.
Screw the pieces into place using the 3mm self-tapping screws.
Tip: You can screw one side completely, slide the power strip in, and then secure the second side for a perfect, tight fit.
This clean and minimalistic design consists of two end clamps that slide onto each side of a standard power strip. By securing the ends instead of the middle, it provides a rock-solid hold that won't flex or wobble when you plug or unplug heavy adapters.
🛠 Hardware Required
Screws: 4x Self-tapping screws (3mm diameter, 2 for each side piece).
📐 Print Settings
This model is designed to be highly functional and extremely easy to print. No supports required!
Supports: No (Print flat on its base).
Material: PLA, PETG, or ABS/ASA (PETG recommended if it's going to hold heavy power bricks or be under constant tension).
Layer Height: 0.20mm - 0.24mm (standard settings work perfectly).
Infill: 20% - 30% (Grid or Gyroid).
Perimeters (Walls): 3 or 4 (Crucial to give the screw holes enough strength to resist the clamping force).
💡 Installation Instructions
Slide the two printed pieces onto both ends of your power strip.
Hold the power strip against the surface (wall, under-desk, or cabinet) where you want to mount it.
Mark the screw holes with a pencil.
Screw the pieces into place using the 3mm self-tapping screws.
Tip: You can screw one side completely, slide the power strip in, and then secure the second side for a perfect, tight fit.
This clean and minimalistic design consists of two end clamps that slide onto each side of a standard power strip. By securing the ends instead of the middle, it provides a rock-solid hold that won't flex or wobble when you plug or unplug heavy adapters.
🛠 Hardware Required
Screws: 4x Self-tapping screws (3mm diameter, 2 for each side piece).
📐 Print Settings
This model is designed to be highly functional and extremely easy to print. No supports required!
Supports: No (Print flat on its base).
Material: PLA, PETG, or ABS/ASA (PETG recommended if it's going to hold heavy power bricks or be under constant tension).
Layer Height: 0.20mm - 0.24mm (standard settings work perfectly).
Infill: 20% - 30% (Grid or Gyroid).
Perimeters (Walls): 3 or 4 (Crucial to give the screw holes enough strength to resist the clamping force).
💡 Installation Instructions
Slide the two printed pieces onto both ends of your power strip.
Hold the power strip against the surface (wall, under-desk, or cabinet) where you want to mount it.
Mark the screw holes with a pencil.
Screw the pieces into place using the 3mm self-tapping screws.
Tip: You can screw one side completely, slide the power strip in, and then secure the second side for a perfect, tight fit.