1 / 8
Triple HDD cage for 120mm fans (infinirail and universal versions) — zdjęcie 1
1 / 8

Triple HDD cage for 120mm fans (infinirail and universal versions)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Fully printed, no support needed stackable HDD cage for 3x drives with TPU decouplers and a 120mm fan on each cage.

Ocena
5 / 5
Polubienia
409
Pobrania
1075
Wydruki
3
Wyświetlenia
8693
Oceny
3

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution

For a detailed guide on how to put this together, please visit our article here:

https://www.corsair.com/explorer/diy-builder/cases/3d-printable-hard-drive-cage/

TL:DR - We have made two versions:

  • Infinirail version - fits FRAME 4000D series and FRAME 5000D Series with support for three cages in each case = nine drives (10 if counting the stock drive plate)

  • Universal version - fits most cases with a spare 120mm fan mount

  • Main part A & B – These are the only parts that changes between the infinirail version and the universal version.

  • Internal support – joining pieces for Main part A and Main part B. six required per cage. We recommend printing one of these in 100% scale, and one in 95% scale to see which fit best for you and then print the remaining five.

  • Stacking connector Front – (not shown above) Connector for stacking multiple cages and joining them together.

  • Stacking connector Rear - (not shown above) Connector for stacking multiple cages and joining them together.

  • Top and bottom cover – optional top and bottom covers to partially enclose the drives and direct airflow.

  • HDD bracket Left & HDD bracket Right – anti vibration drive inserts. One of each per drive, six in total for a full cage.

  • HDD bracket support – (not shown above) Support piece used if you are printing the HDD brackets out of TPU (recommended for vibration dampening, but PLA/PETG will also work)

  • Zip tie bracket Single - Cable tidying solution for single cages.

  • Zip tie bracket End piece for stacking - (not shown above) cable tidying solution for when using two or three drive cages.

  • Zip tie bracket Middle piece for stacking - (not shown above) cable tidying solution for when using three drive cages.

Hardware needed

Below is a list of hardware needed below, this is per cage. If you are printing more than one you will need to multiply these by the number of cages according to which version you print.

Infinirail version

  • 8x M3 nut (only four is required if you are just printing a single cage)

  • 6x M5 nut

  • 6x UNC 6-32 screws for each hard drive (The same type you will use on a motherboard). Around 6mm length is optimal here

  • 8x M3x12mm screws– (only four is required if you are just printing a single cage) 18-20mm are suitable

  • 6x M5x18mm screw – screws between 18-30mm are suitable

  • 4x Case fan screws

  • Super glue

  • 1x UNC 6-32 screw for each hard drive. This is an optional screw to fix the harddrive to the cage if the drives slot opening points downwards. 10mm length is needed here.

Universal

  • 8x M3 nut (only four is required if you are just printing a single cage)

  • 6x UNC 6-32 screws for each hard drive (The same type you will use on a motherboard). Around 6mm length is optimal here

  • 8x M3x12mm screws– (only four is required if you are just printing a single cage) 18-20mm are suitable

  • 4x M4 nut

  • 4x M4x35mm screws - 30-35mm works

  • Super glue

  • 1x UNC 6/32 screw for each hard drive. This is an optional screw to fix the harddrive to the cage if the drives slot opening points downwards. 10mm length is needed here.

Tagi