Liczymy pasujące modele…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
A ground up redesign of last years box. This box prints as 1 piece and does not need supports. This box is meant for 4 12mm RGB Pixels, each eye has 2 behind it. The design allows for an optional difuser to be able to block off light for…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
50Cal Ammo Box PSU mount We have 2 mounts that fit snug into a standard 30cal ammo box and is designed to fit either Meanwell LRS 350 or Generic PSU. The PSU mount is offset to give about 2.1" of space for a controller mount and…
30Cal Ammo Box PSU mount This mount fits snug into a standard 30cal ammo box and is designed to fit a Meanwell LRS 350 PSU. The PSU mount is offset to give about 2.1" of space for a controller mount and controller. There is a M4 screw…
Simple 1/2" and 3/4" PVC Shingle Clip Category: DIY
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for Meanwell LRS 350 or Meanwell LRS 600 (pick the STL for the correct PSU) The design has a in-cut on the bottom to allow for nuts/bolts to…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
Simple PSU Standing mount There are 2 mount designs Meanwell LSR 350 Universal PSU's The mount has 3 holes, 1 on the bottom middle (flush mount) which attaches to the PSU. 2 on the bottom outside which can be used to mount the bracket to…
Simple feet to secure your PSU to an enclosure. These feet are designed to fit in conjunction with any of our PSU Mounts. The PSU Mount fit on top of the feet and they both share the screw to secure the feet to the PSU. Category:…
PSU Mount for Falcon SRx2 Controller. There are 2 versions available. MW LRS 350 - Fits standard Meanwell/Generic PSU's MW LRS 600 - Fits thin Meanwell LRS 600 PSU's The design has a in-cut on the bottom to allow for nuts/bolts to rest…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
3/4" EMT 10 and 12 hold Pixel Tree Topper. This is used to hold LED Strips for mini/mega pixel trees. The design allows for the topper to slide on the pole, but is very snug. You use a screw/nut to tighten the topper to the poll Print…
PSU Mount for Wasatch Pixels Advanced Eight Controller. There are 2 versions available. MW LRS 350 - Fits standard Meanwell/Generic PSU's MW LRS 600 - Fits thin Meanwell LRS 600 PSU's The design has a in-cut on the bottom to allow for…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
Simple to print Staggered PSU Mounts for stacking 2 PSU's together. The staggered design allows easy access to the terminals. The design also provides about 40mm of space between the PSU's which will allow for quality airflow. This design…
These clips are made to fit standard schedule-40 PVC. Sizes: 1/2" - .84mm diameter 3/4" - 1.050mm diameter Print Settings Notes: Print with PETg or PLA+ Info 3-4 walls 3-4 layers 10-15% infill Category: DIY
PSU Mount for Falcon SRx4 Controller. There are 2 versions available MW LRS 350 - Fits standard Meanwell/Generic PSU's MW LRS 600 - Fits thin Meanwell LRS 600 PSU's The design has a in-cut on the bottom to allow for nuts/bolts to rest…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
PSU Mount for Genius 4 Port Controller. This is for the v2022 model, the 4 hole board. There are 2 versions available. 1) MW LRS 350 - Fits standard Meanwell/Generic PSU's 2) MW LRS 600 - Fits thin Meanwell LRS 600 PSU's The design has a…
PSU Mount for Genius 16 Output Controller. There are 2 versions available. MW LRS 350 - Fits standard Meanwell/Generic PSU's MW LRS 600 - Fits thin Meanwell LRS 600 PSU's The design has a in-cut on the bottom to allow for nuts/bolts to…
Simple to print Stacked PSU Mounts for stacking 2 PSU's together. The Stacked design allows easy access to the terminals, but they are not offset. The design also provides about 40mm of space between the PSU's which will allow for quality…
Needed a stake without the eye holes. Simple splice/paste and simple remix. This has been sized to 170mm i length as that is what I needed Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 200…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
Sizes: 1/2" - .84mm diameter 3/4" - 1.050mm diameter Print Settings Notes: Print with PETg or PLA+ Info 3-4 walls 3-4 layers 10-15% infill Category: DIY
Falcon - SRx2 Vertical Mounting Plate This plate fits on side of MW 350 PSU and screws onto the side via M4 screws Use the spacer.stl file attached to put into the whole to offset the controller from the board. Use the centered feet from…
1/2" EMT 10 and 12 hold Pixel Tree Topper. This is used to hold LED Strips for mini/mega pixel trees. The design allows for the topper to slide on the pole, but is very snug. You use a screw/nut to tighten the topper to the poll Print…
HP PSU Vertical Mount for 30Cal Harbor Freight Ammo Boxes. These mounts will support/allow for most of our Smart Receiver and Distro Board Mounts. This mount is designed to have the feet fit snug inside the standard 30Cal Harbor Freight…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for Meanwell LRS 350. This will hold 2 PSUs and removes the need for an extra mount setup for stacking the PSU's The design has a in-cut on…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for Meanwell LRS 350. This will hold 2 PSUs and removes the need for an extra mount setup for stacking the PSU's The design has a in-cut on…
Falcon - v2 Smart Receiver MW 350 Vertical Mounting Plate This plate fits on side of MW 350 PSU and screws onto the side via M4 screws Use the spacer.stl file attached to put into the whole to offset the controller from the board. Use the…
These clips are made to fit standard schedule-40 PVC. Sizes: 1/2" - .84mm diameter 3/4" - 1.050mm diameter Print Settings Notes: Print with PETg or PLA+ Info 3-4 walls 3-4 layers 10-15% infill Category: DIY
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
HP PSU Vertical Mount for 50Cal HF (Harbor Freight) Ammo Boxes. These mounts will support/allow for most of our Smart Receiver and Distro Board Mounts. This mount is designed to have the feet fit snug inside the standard 50Cal MTM Ammo…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for Meanwell LRS 350. This will hold 2 PSUs and removes the need for an extra mount setup for stacking the PSU's The design has a in-cut on…
Simple to print Staggered PSU Mounts for stacking 2 PSU's together. The staggered design allows easy access to the terminals. The design also provides about 40mm of space between the PSU's which will allow for quality airflow. This design…
This PSU Raspberry Mount is designed to fit the standard hole dimensions for Raspberry Pi 2B, 3B and 4B. The design has an in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only uses top screw holes on the PSU to…
PSU Mount for Dual Genius 4 Port Controller. There are 2 versions available. MW LRS 350 - Fits standard Meanwell/Generic PSU's MW LRS 600 - Fits thin Meanwell LRS 600 PSU's The design has a in-cut on the bottom to allow for nuts/bolts to…
Simple to print, print face down. Print 1x Dig Controller Mount 2x HP Strap Mount 4x Spacers This PSU Mount is designed to fit the standard hole dimensions for HP PSU The design has a in-cut on the bottom to allow for nuts/bolts to rest…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for Meanwell LRS 350. This will hold 2 PSUs and removes the need for an extra mount setup for stacking the PSU's The design has a in-cut on…
HP PSU Vertical Mount for 30Cal MTM Ammo Boxes. These mounts will support/allow for most of our Smart Receiver and Distro Board Mounts. This mount is designed to have the feet fit snug inside the standard 30Cal MTM Ammo Box. Print laying…
PSU Mount for Genius Long Range Controller board(s). This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell) (should fit any PSU with 150mm between mounting holes). The design has an…
Falcon - SRx4 Smart Receiver Mounting Plate This plate fits on the side of the MW 350 PSU and screws onto the side via M4 screws Use the spacer.stl file attached to put into the whole to offset the controller from the board. Use the…
Simple to print Single PSU Mounts for securing a PSU to an enclosure. You will want to print the file 2x for a full setup This design is generic, will fit any PSU with 150mm spacing between the mounts. Mounts using M4 bolts. Print…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
These clips are made to fit standard schedule-40 PVC. This will hold 2 rows of PVC, one above the gutter, one hanging blow PVC Sizes: 1/2" 3/4" EMT Sizes: 1/2" Print Settings Notes: Print with PETg or PLA+ Info 3-4 walls 3-4 layers 10-15%…
This mount will allow you to mount a Falcon F16v3 (works on V2 as well) Expansion board to a PSU. You will need to print 4 spacers. The tolerance for the spacers is tight, they should fit inside the holes on the top of the board. Mounting…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for PSU (verified on Alitove and Meanwell). The design has a in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
Simple to print, print face down. This PSU Mount is designed to fit the standard hole dimensions for Meanwell LRS 350. This will hold 2 PSUs and removes the need for an extra mount setup for stacking the PSU's The design has a in-cut on…
PSU Mount for Genius 4 Port Smart Receiver board(s). This is designed for the 2023 edition. This PSU Mount has 2 designs, each fits a different size PSU. PSU Options Available MW LRS 350 - Fits standard Meanwell/Generic PSU's MW LRS 600 -…
PSU Mount for Genius Long Range Controller. There are 2 versions available. 1) MW LRS 350 - Fits standard Meanwell/Generic PSU's 2) MW LRS 600 - Fits thin Meanwell LRS 600 PSU's The design has a in-cut on the bottom to allow for…
HP PSU Vertical Mount for 50Cal MTM Ammo Boxes. These mounts will support/allow for most of our Smart Receiver and Distro Board Mounts. This mount is designed to have the feet fit snug inside the standard 50Cal MTM Ammo Box. Print laying…
PSU Mount for Genius 16 Port Long Range Receiver. There are 2 versions available. 1) MW LRS 350 - Fits standard Meanwell/Generic PSU's 2) MW LRS 600 - Fits thin Meanwell LRS 600 PSU's The design has a in-cut on the bottom to allow for…
Genius - 4 Port Smart Receiver MW 350 Vertical Mounting Plate This plate fits on side of MW 350 PSU and screws onto the side via M4 screws Use the spacer.stl file attached to put into the whole to offset the controller from the board. Use…
This PSU Mount is designed to fit the standard hole dimensions for HP PSU. This system includes the Controller Mount and the HP PSU staps The design has an in-cut on the bottom to allow for nuts/bolts to rest above the PSU. Design only…
This mount is designed to fit 3 Dig-Uno Controller boards, this will allow higher density in your box. This PSU Mount is designed to fit the standard hole dimensions for Meanwell LRS 350, Generic PSU, and Meanwell LRS 600 The design has a…
PSU Mount for Genius - Dual 4 Port Smart Receiver Controller Mounting system. This is designed for the v2023 model, the one with 3 screw holes. This is designed to be used in conjunction with our HP PSU Straps…
To wszystkie aktualnie dostępne wyniki.
