Liczymy pasujące modele…
The holder is inspired (not a remix) by the DOPE Card Holder V3 by Tarz Printed in Prusament Prusa Galaxy Black PETG with 30% infill. Required hardware 2 x M4 12mm Button Head Socket Cap Screw (like these ) 1 x M4 16mm Button Head Socket…
Tikka T1x is a great rimfire rifle, but the bolt handle is slick and small. When I run bolt faster - my fingers tend to slip off the handle from time to time. I designed a knob that fits on top of the stock bolt handle and allows a better…
I have a ¼ in tubing running from the reverse osmosis filter under the sink to the refrigerator to feed water to icemaker. It is hot glued to exposed particle board a few inches off the floor, right under the base cabinets bottoms and the…
The holder is designed for E-Dope by DRS , inspired (not a remix) by the DOPE Card Holder V3 by Tarz E-Dope is retained in the holder by three flaps. A 1 mm wall on the top side prevents E-Dope from sliding out, but the holder flexes just…
This is a buttstock extension that can be added as a spacer between the buttstock of the KRG Chassis and its KRG Recoil Rad, to adjust the length of pull. According to KRG website , all KRG chassis use the same recoil pad, but keep in…
I really liked 22LR Bullet Holder by @SkippyMcSlappyPants and used them for CCI Standard Velocity for a few years. I wanted a similar box for SK ammo, but original design was made specifically for the flat CCI bullet holders and alike.…
I'm using Athlon Ares BTR 4.5-27x50 scope with a sun shade and low scope rings on top of a canted Picatinny rail. This brings the front edge of the sun shade very close to the barrel. The fit is so tight that I can't use my favorite…
Inspired by the suction cup holder by @AyyArr, made to print simpler. Does not require supports. The tag is held by friction (could be very tight fit - don't worry, it'll be fine). Printed with clear Prusament PETG. Used with 20mm suction…
Two desiccant containers are identical (not left- or right-specific parts) and hold about 3lbs of silica-gel combined. Taller roller brackets are required to free up space under the roller for the containers. Solid spots on the bottom…
For some unknown reason, developer decided to place the thermostat on the wall in master bedroom. It wasn't a problem until I replaced an original “dumb” thermostat with ecobee 3 Lite. ecobee 3 Lite has a bad habit of flashing the screen…
Designed to be mounted onto an upright of a wire rack with three zip ties. Can be mounted to any vertical tube of a diameter of up to 25.6mm. The gauge simply slides into the holder from above with the hose & chuck hanging down freely.…
These bottom plates are required when the Modular Control Panel by PrinterBox is used in combination with following mods: PrusaBox w1219 Temperature Control Housing by Colin PrusaBox Enclosure - Adapter Plate to Center Modular Control…
I'm working on the controller for the beside lamps, which requires an enclosure with two panel mounted 2-pin AC sockets, like these I couldn't find a corresponding model, or existing designs that use these sockets. So I had to design a…
A simple magnetic bracket that can be easily removed to clear the door opening for pulling the spools, and just as easily placed back. Designed for very common panel mount rectangular 48 x 28 x 15 mm hygrometer/thermometer that can be…
To wszystkie aktualnie dostępne wyniki.
![[PrusaBox] Bottom plates for modular panel with centering adapter plate and Expandable Steel Sheet Holder](https://media.printables.com/media/prints/991730/images/7553548_5d27a34c-7231-4099-b1f1-2df100796a10_c9d18e4d-515f-411e-8489-ed93ebaa980d/capture.png)
