Liczymy pasujące modele…
This print is for a mechanical iris with a open ID of 110mm and a overall OD of 180mm minus mounting lugs. Files include cad drawings in FreeCad 0.19, STLs, PursaSlicer 2.4.1 3mf files, and pre sliced gcode for a i3 MK3. If you re slice…
Remix of the Enclosure for Arduino GIGA R1 WiFi and GIGA Display Shield with a open back to allow access to IO ports
This is a low profile cover for the Swerve Drive Specialties MK4i drive system. The cover is designed to fully cover the drive all the way down to the mounting plate so the belt is fully covered. Also there are mounting points for adding…
Collection of 4 divider designs make to fit Blue Demon RST-36 TIG filler rod storage tubes 2 compartment 50/50, 3 compartment 50/25/25, 3 compartment 33/33/33, 4 compartment 25/25/25/25 No special printing requirements. Did mine with a…
This cover is for the standard 120A FRC breaker. Covers the electrical connection studs to prevent accidental contact. 3 versions included: Electrical entry strait in and strait out Electrical entry right angle in and strait out…
This part is a replacement for the inside handle cam that can break with abuse. To replace remove the nut attaching the inside handle and slide it off. Remove the old cam from the handle. Reverse order to reassemble with new cam. :) Model…
Minimal mounting clip system for the NI RoboRio used in FRC. Clips are designed to use standard #6 or 6-32 machine screws. Clips insert into the side zip tie holes on the RoboRio. The slots are set up such that you can loosen the screws…
Replacement TPU tire for a BRIO battery operated train. This one was a PE-426 but likely would work with others. Printed in TPU with 100% infill and 3 perimeters. Note if the print boogers turn down the volumetric flow / print speed. Had…
This is a set of standoffs to support 1.6mm and 0.62 mm thick boards. These were designed to work with the PCB stencil printer described here: https://dengler-mechatronik.de/?p=560 (not my design) The bottom of the prints has pockets for…
Replacement hand wheel for Husqvarna 6000 series machines. This was modeled off the broken wheel on my 6440 which is no longer available. Typically there are 2 metal clips (only one shown as the other was lost) that hold the wheel on the…
Crisper for the 2024 CypherCon 7 badge. What does it do? Print one out and bring it along to CypherCon 7 to find out. Printing instructions: 0.4mm nozzle 0.2mm layer height No supports 15% infill Any ridged material Dark opaque color will…
These are clips that slot into MasterForce rack shelving uprights. These are sold at Menards and other big box stores.…
This is a replacement door stop for a Grundig console radio. This supports the fold down door rod. Note this is just the inner part you need to reuse the outer “ring” and mounting screws. Recommended print materteral and settings: PETG,…
Had issues with my flashlight turning on in my pocket so made a set of button protectors / caps. One is solid and has to be removed to turn on the flashlight and the other has a raised rim around the button, Both cases the cap just slides…
This is a 2 way (vertical or horizontal) side mount bracket for the typical round hygrometer that need a 42mm hole. Made this for use with the ezystorage 79-Quart Waterproof Clear Latching Gasket Tote I use for storing filament. (FYI you…
This is all the 3D printed parts for the official Cyphercon 2026 badge. The included 3mf file shows the recommended orientation and supports. https://cyphercon.com/ Along with this set of prints you will also need the following parts to…
Have a mixed set of buckyballs and neocube 5mm magnets and was having a hard time getting them back in a cube to put back in the packages. This print makes it a bit easier and should work with any 5mm spherical magnets. To use load one…
To wszystkie aktualnie dostępne wyniki.
