P
PrintablesRavenwreck
Wheel center cap
Modelled this for a friend and don't remember what car/wheels he had so you'll have to check the measurements. STEP file included.
- Pobrania
- 1240
- Polubienia
- 140
- Ocena
- 5
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesRavenwreck
Bambu labs X1C build plate holder with sideloading
Needed a build plate holder that can be loaded from the side so I can put it on a shelf that has another shelf above it. Holds 5 regular thickness Bambu labs X1/X1C/P1P plates. STEP file included.
- Pobrania
- 392
- Polubienia
- 23
- Ocena
- 5
P
PrintablesRavenwreck
Ryobi battery project box
Update 13.3.2025: Fixed ovesize hole in Battery middle, new version is V1.1. Didn't update the full STEP project but instead I uploaded a separate STEP file of the middle part. Use this box as a template to build your own electronics…
- Pobrania
- 356
- Polubienia
- 86
- Ocena
- 0
P
PrintablesRavenwreck
USB cable tester enclosure
Provides some protection for the bare pcb but covers up probing points. Place the pcb in the lid part and slide them in the bottom part. Can be tight to undo, but possible. Printed with PETG so it has some flex. STEP file included.
- Pobrania
- 348
- Polubienia
- 67
- Ocena
- 4,85
P
PrintablesRavenwreck
BigTreeTech TFT35 V3 Case
Couldn't find a nice basic case so I designed one from scratch. Holes for SD and USB. Not sure if there is clearance for ESP-module or other cables than the flat cables shown in pictures. Screwholes sized for 3 mm screws.
- Pobrania
- 347
- Polubienia
- 33
- Ocena
- 5
P
PrintablesRavenwreck
IP2X test finger probe mockup
Obviously not very official but if you are curious about electrical safety here's a probe for you. To preserve dimensional accuracy I split the finger so it could be printed without supports. Use bits of filament to align pieces and glue…
- Pobrania
- 289
- Polubienia
- 13
- Ocena
- 5
P
PrintablesRavenwreck
Sony Xperia 10 IV bumper case
UPDATE 2023-04-07: Added a case with a slot for a wireless charging receiver. Also hides the connector so less chance of it snagging on something and ruining your usb port. I measured roughly 400mA charging current so beware it is very…
- Pobrania
- 284
- Polubienia
- 18
- Ocena
- 5
P
PrintablesRavenwreck
Depth gauge 0-16 mm
Usage: turn the knob clockwise to expose the pin a certain amount and read the measured distance off the side where the line of the slide and markings on the side align. Uses M3 countersunk screw to attach the knob to the piston. To…
- Pobrania
- 268
- Polubienia
- 101
- Ocena
- 4,5
P
PrintablesRavenwreck
Pen holder for HSW
Designed to hang from the botton row of the HSW and it extends backwards a bit so you can't place this in the middle of the wall. Screwholes are M3 sized countersunk and are near impossible to screw in. Had to remix an insert so I could…
- Pobrania
- 259
- Polubienia
- 61
- Ocena
- 5
P
PrintablesRavenwreck
Small dustpan
The opening is roughly 125 mm across.
- Pobrania
- 221
- Polubienia
- 19
- Ocena
- 5
P
PrintablesRavenwreck
M.2 SSD drive protective sleeve
Disk sizes in millimeters: Small (bare disk) 2.75 x 22.50 Medium (akasa heatsink) 9 x 22.75 Large (jonsbo heatsink) 10.05 x 25 Use arachne engine or adjust your line width to even the wall count to 2 to save time. STEP file and Fusion360…
- Pobrania
- 221
- Polubienia
- 22
- Ocena
- 5
P
PrintablesRavenwreck
DEEJ mixer case
Case for 5 potentiometers and an arduino nano (clone) to use with deej. Two prongs on the inside need supports. Arduino might need some hotglue to keep in place. STEP file included.
- Pobrania
- 194
- Polubienia
- 27
- Ocena
- 5
P
PrintablesRavenwreck
MT3608 Boost converter screw mount
Mount your converter with screws. Hole sized for 23 mm screws. Use supports under the clip parts. When unscrewed should flex enough even with PLA to get the board in and after screwing in should hold it tight. STEP file included.
- Pobrania
- 180
- Polubienia
- 13
- Ocena
- 0
P
PrintablesRavenwreck
Nut sorter M5 M4 M3
Stack the pieces from botton up: base, M4, M5; dump your mixed nuts in and set the lid on top. Hold on tight and shake. Chamfers should hold the package together and after shaking the top level should only have M5 nuts, M4's on the second…
- Pobrania
- 167
- Polubienia
- 55
- Ocena
- 5
P
PrintablesRavenwreck
Notebook holder for HSW
Uses M3 countesunk screws. Suitable remixed insert included that you can tap to M3, use self tapping screws or use M3 screws to form threads. STEP file included.
- Pobrania
- 155
- Polubienia
- 61
- Ocena
- 5
P
PrintablesRavenwreck
InfiRay P2 Pro thermal camera case
Uses the original foam from the package cut to 40 x 40 x 17 mm (xyz) piece that is hot glued to the middle and a piece of thin felt on the lid. I have the regular version so no place for the macro lens. Uses M3x20 screw for the hinge. I…
- Pobrania
- 153
- Polubienia
- 16
- Ocena
- 5
P
PrintablesRavenwreck
Electrical cabinet key keychain - triangle 10mm
Uses M4x12 as a hinge. I recommend harder materials. PCTG is great because of its layer adhesion. Has a flat side for embossing something in your slicer or 3D CAD software. STEP file included.
- Pobrania
- 130
- Polubienia
- 19
- Ocena
- 5
P
PrintablesRavenwreck
Pocket case for 50 mm screwdriver bits
Secure flat case for 12 50 mm long ¼ inch screwdriver bits. Insert clicks in place after pushing it in the case. Squeeze the sides of the case to release. PETG recommended for its flexibility. Depending on your printer tolerances the…
- Pobrania
- 125
- Polubienia
- 27
- Ocena
- 4
P
PrintablesRavenwreck
Ender 3 Y gantry support bracket
If you ever upgraded your hotend and lost some printing area a good way to regain some is to unscrew the two screws that hold the Y profile, move the profile forward and screw in just the front screw to the backmost hole in the Y profile.…
- Pobrania
- 112
- Polubienia
- 31
- Ocena
- 5
P
PrintablesRavenwreck
Stanley Workmaster Screwdriver Handle bit extension remix
Remixed engineererrants model of Stanley Workmaster Screwdriver Handle to accept a regular bit extender (hex shaft 25 mm long, round shaft diameter 10 mm). Also made a 80% scaled down version. Check the original model for editable source,…
- Pobrania
- 111
- Polubienia
- 16
- Ocena
- 5
P
PrintablesRavenwreck
Machine handle knob 3/8 -16 UNC
Thread is 3/8-16UNC, 16 mm deep. Sphere diameter is 45 mm which is slightly larger than a golf ball. STEP file included.
- Pobrania
- 105
- Polubienia
- 12
- Ocena
- 5
P
PrintablesRavenwreck
Hot air gun clip on stand with a magnet
Made this because the holder that came with the gun is wall mounted and I didn't want to take it off the wall when I needed to do some remote work. Clips around the handle and you can slide it back and forth to activate and deactivate the…
- Pobrania
- 102
- Polubienia
- 26
- Ocena
- 5
P
PrintablesRavenwreck
Power strip holder - EU
Leaves room for smart switches or other large items. STEP file included.
- Pobrania
- 101
- Polubienia
- 15
- Ocena
- 5
P
PrintablesRavenwreck
Small rake
Print the rake on its side and use supports. Glue to the handle. STEP file included.
- Pobrania
- 98
- Polubienia
- 10
- Ocena
- 0
P
PrintablesRavenwreck
Nilfisk power washer inlet filter housing.
Power/pressure washer inlet filter housing for Nilfisk washer. Modeled this for a friend. Use the o-ring from your broken one and use some soap if the fit is tight. Thread is BSP ¾ with an small inbuilt negative offset so should have no…
- Pobrania
- 97
- Polubienia
- 8
- Ocena
- 5
P
PrintablesRavenwreck
CNC Kitchen TS100/101 heat set insert tip storage
Edit 12.10.2023: There might be different size tubes out there. This one fits if your tube inner diameter is roughly 14 mm. Check comments and remixes for slimmer versions. Ordered the TS100/101 soldering adapter and tips set by…
- Pobrania
- 68
- Polubienia
- 31
- Ocena
- 5
P
PrintablesRavenwreck
Xiaomi bt temperature sensor wall holder
Way to wall mount the sensor so that it is easier to change the battery later. Make sure to align the holes. I recommend VHB tape for mounting.
- Pobrania
- 64
- Polubienia
- 8
- Ocena
- 5
P
PrintablesRavenwreck
Keyswitch thumb trigger
Used instruction on here to build a remote shutter button for android devices: https://vervainglobal.com/articles/remote-shutter.html The model is a housing for a keyswitch that you can hold comfortably in your hand a push with your…
- Pobrania
- 60
- Polubienia
- 7
- Ocena
- 0
P
PrintablesRavenwreck
Small shelf - F360 parametric
Use 3 mm diameter screws. Min. 8-10 mm long for feet and top shelf, 15 mm for stacking. Feet are optional but I imagine they distribute the load a bit and it is easier to attach some protective felt. 3mf files for multiple sizes provided.…
- Pobrania
- 54
- Polubienia
- 17
- Ocena
- 5
P
PrintablesRavenwreck
Keystone Panel Mount countersunk remix
Remix of Keystone Panel Mount by M Hole diameter is 3.4mm and the screwhead (widest part of the scew) 6.25mm.
- Pobrania
- 52
- Polubienia
- 14
- Ocena
- 0
P
PrintablesRavenwreck
Magnetic collector wand
Known as “swarf collector” if you need to google it. Works also for collecting the box of washers you drop to the floor. Push the magnet all the way to the tip of the shaft and roll the tip over the things you are collecting. Move the…
- Pobrania
- 51
- Polubienia
- 12
- Ocena
- 5
P
PrintablesRavenwreck
Keychain rule 10cm
Edit: 29.08.2023: Realized that when used in a keyring it opened the wrong way so I mirrored everything and modified to be printable. Sorry for the inconcenience. ------ Measure small things on the go. Pressing the two halves together can…
- Pobrania
- 51
- Polubienia
- 4
- Ocena
- 5
P
PrintablesRavenwreck
Spool - F360 parametric
Originally made for spools of electrical wire that came packed very much like poorly spooled masterspool refills of filament. Design went untested because I didn't have a printer big enough to print proper size spools. The center prongs…
- Pobrania
- 50
- Polubienia
- 6
- Ocena
- 0
P
PrintablesRavenwreck
4 mm banana socket nut driver
Tool to tighten those pesky nuts that need a special tool. Thread diameter 11.75mm and nut outer diameter 14.35mm. STEP file included.
- Pobrania
- 50
- Polubienia
- 3
- Ocena
- 5
P
PrintablesRavenwreck
Case for hole punch set
Simple case for 9 hole punches from 2mm to 10mm in 1 mm increments. STEP file included.
- Pobrania
- 47
- Polubienia
- 1
- Ocena
- 5
P
PrintablesRavenwreck
Countersink bit case
Remixed Altoid countersink bit holder by @Billiam since my 8mm bit was slightly longer than his and since Altoids don't exist where I live I also made up a simple friction fit lid for the case. STEP file included.
- Pobrania
- 46
- Polubienia
- 6
- Ocena
- 5
P
PrintablesRavenwreck
Air duster nozzle - F360 parametric
For Reesibi branded battery powered air duster/blower but may apply for others as well. Bayonet opening diameter is 24 mm and the peg is 4 mm. Few examples are included if you don't have Fusion 360 installed. If a projection breaks on the…
- Pobrania
- 43
- Polubienia
- 6
- Ocena
- 0
P
PrintablesRavenwreck
Extension for 63A ABB fuse switch handle
Print with the text side down. Use supports. STEP file included.
- Pobrania
- 36
- Polubienia
- 5
- Ocena
- 0
P
PrintablesRavenwreck
UNI-T UT120 multimeter wire organizer sleeve
PETG or other filament with similar flex recommended. Haven't tried with PLA but might work. Brim also recommended but depends on your confidence on your bed adhesion. Print with the probe holder part down on the bed. Needs a few…
- Pobrania
- 34
- Polubienia
- 4
- Ocena
- 5
P
PrintablesRavenwreck
Replacement pad for Bessey XC3 clamp
Flexible filaments recommended. Shore 98A woks well and is tighter than the original. STEP file included.
- Pobrania
- 29
- Polubienia
- 3
- Ocena
- 0
P
PrintablesRavenwreck
Air duster nozzle storage hook
Hanger to store air duster/blower nozzles or other similar items. Print two pieces of “Link tube” to join body parts. Should be friction fit but if there's any doubt there's always glue. Bottom spacer is optional. I needed it since my…
- Pobrania
- 24
- Polubienia
- 5
- Ocena
- 0
P
PrintablesRavenwreck
Large square vacuum nozzle
Square outside measurements are 160 mm x 160 mm and the ryobi adapter inside diameter is 32 mm but it also fits my regular vacuum. Included is a blank adapter that you can use to modify for different size vacuum. Unfotunately the surface…
- Pobrania
- 14
- Polubienia
- 3
- Ocena
- 0
P
PrintablesRavenwreck
Lithium cell charger case
Bought one without soldered terminals and used my own so this might not fit the one that comes with the terminals soldered. Lid slides from the rear. Use two 3 mm countersunk screws to screw everything together. Suggested printing…
- Pobrania
- 9
- Polubienia
- 1
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.