Liczymy pasujące modele…
Attached PDF contains full documentation on how to integrate a Filament Runout Sensor in Marlin FW in an Anet A8 printer. Special thanks to Caverntwo on YouTube who is the inspiration for this documentation and the Anet A8 with Marlin…
This is a LM12UU PTFE linear bearing based on romanz' LM10UU linear bearing. I.D. with PTFE Tubing: 12mm (nominal) I.D. without PTFE Tubing; 14mm O.D: 21mm at 4mm each end and 20.5mm in middle Length: 30mm Need 4mm O.D. x 2mm I.D. PTFE…
This is an updated design for 3D Solutech Masterspool filament. 3D Solutech is a US based filament manufacturer that is starting to provide Masterspool filaments. This design is specific to 3D Solutech Masterspool filament with a…
This is a simple 3.5mm spacer for a NEMA-17 stepper. It was designed to offset a Zyltech NEMA-17 stepper for a Piper 2 500mm+ gantry aligning the 10mm belt with the carriage. Print Settings Printer: Anet A8 Rafts: No Supports: No…
This REMIX is a combination of two types of enclosure filters, see "How I Designed This" for more into. BOM: 12 - #4 self-tapping sheet metal screws, 3/4" long. 1 - HEPA filter with tab cut off:…
Anet A8 comes standard with 20A (240watt) PSU. Upon the stock PSU dying, a 30A (360watt) PSU was purchased to replace: https://www.amazon.com/gp/product/B00D7CWSCG/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1 30A PSU does not fit stock…
This is remix of my original #Masterspool to integrate a 608 bearing right into the hub. Original Design w/o 608 bearing I.D.: https://www.thingiverse.com/thing:3187986 3D Solutech is a US based filament manufacturer that is starting to…
This is a REMIX and enhancement to the Filament FAULT detector by re-NABLE. re-NABLE's design is good, but I had a couple minor issues: I wanted to integrate it into a heated dry box: https://www.thingiverse.com/thing:2778707 The re-NABLE…
Remix and enhancement of hobie77's "Geared Bowden Extruder v2". Re-designed package to use a 25mm screw, added a cage/outer support for large pulley, filament runout sensor, and PTFE fittings. Calibrate E-Steps using Bowden method:…
Was looking for a good C270 mount for my Piper 2 U.S. 1/2" EMT printer. Found luc_e table top mount and thought it was awesome: https://www.thingiverse.com/thing:1228521 . I wanted something that attached directly to the gantry or frame,…
U.S. light switch I modeled up for my son's "DC Superhero" bedroom remodel. Please post your make if you print one. Print Settings Printer: Anet A8 Rafts: No Supports: Yes Resolution: 0.2mm Infill: 20% Filament: 3D Solutech PLA Real…
This is a NEMA 17 Stepper Motor mount sized for U.S. 1/2" EMT Tubing. I designed this for a Piper 2 CoreXY Extruder of my own design: Belted Extruder v1 - https://www.thingiverse.com/thing:3289589 Belted Extruder v2 -…
Wanted a clean way to route the gantry wiring of a Piper 2 printer. Cable chain is raised to be 5mm above the highest point of the gantry. Both Extruder and Gantry ends allow for bi-directional swinging so routed cables won't get into too…
This is a Filament runout sensor mount with/without a Bowden E-Stepper motor mount. Designed to sit on top of the Anet A8 acrylic frame, on the right hand side. Removal of the small acrylic paddle keeping the smooth guide rod is necessary…
This Dasaki case will fit the following MCU's: Arduino Mega 2560 Arduino DUE (not physically tested yet) Adafruit Grand Central M4 Panucatt Re-ARM It has plenty of height room for the MCU, RAMPS board, Step Stick Protectors, Step Sticks,…
This a Z-Axis Cable Chain for the 1/2" U.S. Piper 2 CoreXY Printer. Parts are designed to insert into EMT tube of left rear gantry when looking at the front of the printer. Mirror z-chain-frame.stl in your slicer for right hand side.…
This is yet another BLTouch mount for the Piper 2 X-Carriage. Based on ANTLABS documents, this positions the BLTouch sensor (or clone) as close to the heat block as recommended (15mm), and at a fixed z-height from tip of hot end to bottom…
The standard axial fan design did not offer enough airflow/cooling for high-speed/higher temp PLA printing on the Piper 2. I didn't want to re-invent a fan cooler nozzle just yet, but needed the air flow that radial fan's produce.…
608 Bearing spindle for 3D Solutech Masterspool. Masterspool can be found here: https://www.thingiverse.com/thing:3187986 You will need to press-fit a 608 roller blade/skate bearing into each piece after printed. Then insert though the…
When building my Piper 2, 500mm+ gantry, I had issues with the 10mm wide belt being pulled out of the slave side when applying tension the opposite side. These little gadgets will clamp on the belt, keeping it from sliding around and out.…
To wszystkie aktualnie dostępne wyniki.
