Liczymy pasujące modele…
Simple, snap on travel cover for a Gillette Fusion razor. Print instructions Category: Household Print Settings Rafts: No Supports: No Resolution: 0.2mm Infill: 15% Filament: Prusa PETG Notes: I'd recommend PETG, since the cover needs to…
14 September 2025 Update: Added mount for generic LM393 H2010 style infrared encoder I discovered the encoder mount was slightly too close to the encoder wheel axis, so in some cases the encoder wouldn't read properly. The REV4 version of…
Simple mounts to attach cheap power strips to the side of a cabinet / table / wall / etc. One bracket is closed end, the other has an opening for the power cord. The screw holes are sized for M4 screws. Solidworks 2017 files are included…
I was having problems with our portable air conditioner's exhaust hose popping off of the window cover. So, I designed a quick-connect to solve this problem. This should fit most portable A/C units with a hose diameter of about 144mm.…
11 August 2026 update: Based on someone's request, I added .step files for the printable parts for your easier remixing Purpose: I wanted to build a compact device for testing and setting the position for RC servos. This device is pretty…
This is an automatic fish feeder controlled by an Arduino. I tried several of the other automatic fish feeders listed online, and didn't have much luck, so I designed my own. It's designed to feed small food pellets, such as the Top Fin…
Simple brackets to hold a Bosch 36v charger on the wall. It is designed to use M4 or M4.5 flat head (countersunk type) screws. Parts are designed to print without support or raft. You may have to rotate the parts individually to sit…
My niece and nephew's Playmobil rescue helicopter had a broken tail rotor. This part is a snap-on direct replacement. You may have to ream out with an appropriately sized drill bit after printing so it freely spins. Print instructions…
This is a GoPro Lanyard mount. I wanted something to attach a GoPro to a standard tradeshow lanyard so my 4 year old could wear the camera around and take videos and photos without worrying about him dropping it. Solidworks 2016 file…
Why scoop endless scoops of coffee to get your coffee maker going? (particularly office coffee makers??) This scoop has a volume of about 130mL which equals about 8.8 Tablespoons. If you have a 14 cup coffee maker this means you only need…
Simple mount that holds a RAMPS 1.4, Arduino MEGA, and cooling fans. Slots in side of "case" allow for neat running of stepper motor and other wires to keep them out of the airflow path. The fan mount is designed to allow the use of…
Work in progress: I wanted to design the cheapest possible automatic plant watering system. You should be able to make this from things you have around the house plus less than $10 worth of parts. This design only requires a few purchased…
I needed a mount to attach a Busch & Mueller LED dynamo powered light to a Specialized Pizza Rack. I didn't find anything suitable online so I designed my own. This uses 2x M5 x 12 SHCS + 2x M5 nuts for the rack clamp, and 1x M5 x 45 SHSC…
This is a M5 screw to replace the visor screw in a Giro Montaro. (probably works in other Giro helmets as well) Rotate on your print platform to print screw head down. Print, then use a M5 tap or M5 nut to cut threads in the shaft. You…
This screw clip is designed to attach a sheet of plastic / perspex / plexiglass / wood to your window, so you can most efficiently use a portable A/C unit. Works with: -35 - 60 mm thick window frames Instructions: -backer nut may not be…
This is a replacement hinge insert for Little TIkes toys. I created this to fix a Little Tikes kitchen we received second hand as a gift for our son. The oven door hinge was broken. I created the 3D model and printed two replacement…
Under desk or wall mount for a Dell WD25TB4 dock. 2x M4 x 10 socket head cap screws to attach dock to mount 3x M4 flat head screws to attach mount to desk or wall Don't use too long of a screw to attach the mount to the dock, or you could…
This is a replacement seatpost mount for a niterider Solas USB taillight. My original mount broke, and I needed a replacement. The clamp is intended for larger seatposts (30.9mm) but will fit smaller posts with rubber shims. Hardware…
These are Ortlieb QL2.1 spacers / inserts to fit the side rails on a Specialized Pizza rack, about 13mm diameter. Solidworks 2020.prt file included for your remixing fun. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No…
I needed to attach a IKEA Hemma ceiling lamp directly to the ceiling- without a steel hook as called for in the directions. This model allows you to do this. The orientation in the model is how I printed it to maximize part strength. I'd…
This dust shoe is designed to work with the Inventables Spindle Carriage, P/N 80031 for the quietcut spindle. It should work with any Shakeoko, Shapeoko2 or Xcarve that has this particular spindle carriage. It's designed for a standard…
These clips are designed to hold low voltage wires for LED undercabinet lighting in place. The wires this particular clip is intended for are about 0.140" wide by 0.068" tall. Use a #6 flat head screw to hold in place. The back side of…
These are replacement coins for the "Learning Journey" kid's cash register. Our dog ate the original coins, and our son was sad. So I made some new ones, and that cheered him right up. Print instructions Category: Toy & Game Accessories
There are three types of Magicshine mounts included in this collection: 1) Handlebar mount, complete design, pinch-clamp 2) Handlebar mount, which uses a GoPro handlebar mount clamp 3) Helmet mount, which uses a GoPro helmet mount Note I…
My toddler son always wants to play with my 'real' quadcopter multicopters. So, I thought making a toy multicopter would be a fun project that he'd enjoy playing with. Solidworks files included for your remixing enjoyment. 1.16.14 update:…
I needed some solid mounts to attach the Inventables drag (cable) chains to my Shapeoko2. The drag chains came with the Shapeoko 2 "The Works" kit but didn't include a method to attach them to the machine. This is an assortment of cable…
This is a replacement drip tray for a Zojirushi NRC-10 Rice Maker. Print instructions Unassociated tags: drip tray, rice maker Category: Replacement Parts Print Settings Printer: Prusa i3 MK2 Rafts: No Supports: No Resolution: 0.2mm…
This is an improved lock design from the original design -less material & faster to print -lower profile, less obvious -easier to attach and remove -should be more secure over rough trails / roads -more resistant to accidental removal…
I wanted a simple adjustable angle FPV bracket for my Crazepony (Crazypony) H210 and 700TVL FPV camera. I couldn't find one that I really liked to I put this together. It's intended to be adjustable, simple & lightweight. I also included…
Update 9/8/13: New part model has thicker walls and larger radii to make it more difficult for our toddler to break the part. The Rev 3 and Rev 4 parts are slightly different- the Rev 4 has the thickest walls. Connects the swiffer handle…
**I just uploaded a newer version of this design please check it out first: http://www.thingiverse.com/thing:456025 This is a mash-up of the Greg's Wade extruder and Terawatt Industry's belt drive extruder. It brings the zero backlash…
This is a replacement filter / grate for a InvisaFlow 4400 Flex Grate Downspout Filter I purchased from Amazon.com: http://smile.amazon.com/gp/product/B0061Q5DW2/ref=oh\_aui\_detailpage\_o09\_s00?ie=UTF8&psc=1 Our dog ate the original…
My toddler wanted a bell on his Strider. Unfortunately, the bells at the bike shop are designed for standard handlebar diameter's, not a Strider's 0.5" diameter bar. Luckily, my 3D printer makes a great adapter! This adapter should work…
This is an adapter that allows you to mount a Magicshine LED headlamp to the gopro mount included with a Giro EDIT helmet. It would probably work for most similar helmet mounts. This mount places the light higher and closer in than my…
Tie a shoelace on to one of the holes, and endless fun for your toddler ensues. Print instructions Category: Construction Toys
These connectors are for use on 5mm output shaft steppers and 3/8" ACME threaded rod. Print instructions Category: 3D Printer Parts Instructions 1) Print 2) Insert 5mm nuts into nut capture slots on bottom of the part. Start M5 x 10 SHCS…
Set of filament guides for a MendelMax printer. I have had all sorts of problems with filament tangling during printing, so I created these guides to eliminate any possible issues. It includes two options for the upper guide- one fixed…
I uploaded a much improved lock design, located here: https://www.prusaprinters.org/prints/70786-ortlieb-ql31-lock-improved-design I have a set of Ortlieb bags for my commuter bicycle that use the QL3.1 mounting system. These work great,…
I needed a way to grip onto my racing drone's motor so I could remove too-tight prop nuts. While gripping the motor with a pliers would work, it would also really scratch up the motor. So I designed this part. Place it over the motor,…
Attaches mechanical endstop switch to the inside edge of the MendelMax frame. Print instructions Category: 3D Printer Parts Instructions This mount attaches the Y-Axis mechanical endstop switch to the inside of the mendelmax frame. It…
These files are three different versions of a mount to attach a Magicshine LED light to a Giro Montaro helmet using it's included GoPro mount. This may work for other helmets and LED Lights, YMMV. Rev 3 is probably the version you'll want…
This is a mash-up of the Greg's Wade extruder and Terawatt Industry's belt drive extruder. It brings the zero backlash advantages of the Terawatt 00str00der design together with a heavy duty, rock solid design. Note: this is designed for…
Mount to solidly affix a TS5823L FPV video transmitter to the rear deck of a Hobbyking Q450 DJI Flamewheel clone frame with integrated power distribution board. It's designed to place the VTX heatsink directly against the PCB frame of the…
I wanted to build a wolfstock style delta-bot, using Makerslide linear slides. But, I wanted to run the belt through the inside of the Makerslide for a cleaner look. This is still very much a work in progress, I'm currently working on…
Adjustable bracket to attach the RepRap Discount LCD mount to your Snowstock or other Delta printer base. The screen angle is adjustable to your liking. The solidworks files (in 2013) are also included for your remixing enjoyment. Print…
This is a re-mix of my Simple RAMPS 1.4 mount to be compatible with the new Re-Arm Smoothieboard. This mount is beefed up from the original RAMPS 1.4 mount to fix some of the original breaking issues I had. Simple mount that holds a RAMPS…
My son's bike had long axles extending out from the sides of the back wheel- great to attach training wheels- but if you don't need training wheels they like to draw blood. So, I designed these simple axle caps. Print instructions…
After a couple years of use, I noticed the original MendelMax 1.5 Y-Axis motor mount was creeping under belt tension. So I designed this mount to provide improved support for the Y-axis motor. Print instructions Category: 3D Printer Parts…
Tool to help tighten / loosen valve stem nuts for Muc-off brand tubeless valve stems. I didn't like using metal tools as they scratched the rim / valve stem nuts so I designed a simple and compact tool. It might work for other brand…
This is a mounting bracket to attach a flashy rear light to your Surly Big Dummy or other Xtracycle cargo bike. Print instructions Category: Sport & Outdoors Instructions The Surly Big Dummy doesn't have a great place to mount a flashing…
Simple, lightweight prop guards to help keep your props intact. Sized for 5" props. Mounts between the motor and the quad frame. Print instructions Category: R/C Vehicles
Remixed lower z-axis motor mount support that includes the Z-axis endstop adjustment screw Print instructions Category: 3D Printer Parts Instructions 1) attach mechanical endstop switch to X-end. I used a 2/56 SHCS in the existing holes…
Mount to hold a Mitutoyo micrometer head to use as the adjustable z-axis endstop. Also includes the lower mount for the switch and rod clamp to hold it to a 10mm rod. Print instructions Category: 3D Printer Parts Instructions The…
I lost the cover for our Apple Slicer, so I designed a new one. It doesn't fit quite as nicely as I'd like, but it seems to work fine. I used white PLA, but PETG or Nylon might be better for added flexibility / toughness. Solidworks 2020…
This is a replacement part for Blistik's Mobius Pan & Tilt. This part allows the use of a HC-SR04 ultrasonic sensor with the Pan & Tilt mount. (use with these parts: https://www.thingiverse.com/thing:1401116 ) The ultrasonic sensor is…
This is a heavy duty, rock solid mount to attach the Gadgets 3D LCD to a MendelMax or any other printer that uses extruded aluminum profile as its frame. Original solid model files are in Solidworks 2013 format. 2014.06.21 Update: Added…
These are replacement covers for Port-A-Dock brand extruded aluminum canoe racks. Somehow our dock was missing the end caps, which made it very easy to scratch our canoe when loading or unloading the canoe from the canoe rack. Print…
This is a IKEA Skadis compatible pegboard that snaps on to the crossbars of 30cm deep IKEA Ivar shelf. I printed in PLA at 15% infill, seems strong enough for light loads. I used organic support for the snap-fit hook. Solidworks .prt and…
Remix of Andreas Kanner's excellent Badger 2040w enclosure design. Thanks for sharing the .STEP files! printed in PLA For ‘battery mount’: organic supports, flat side to print bed other components used: 1x Pimoroni Badger 2040w 4x M2 x 8…
My toddler pulled the button out of my Niterider Solas and lost the part. I printed this in black Ninjaflex. It was a little tricky to print correctly- I had to play with the print settings to get the part to resolve properly and not turn…
These are improved mounting brackets for B.K. Licht LED Light Bar Type BKL1003. I purchased this light off of Amazon .de. It is a great light, but the provided mounting method is not very secure. I designed this brackets to fix this…
Replacement circular dust bin filter for a Amazon Basics B07K94GQ23 model number VUS30ASS5 Bagless 3.0L upright vacuum cleaner. Unfortunately Amazon doesn't seem to sell replacement filters, and none of the generic filter brands carried…
This is a 'water bottle cage' type mount for a Yeti Rambler style insulated coffee mug. Designed in Solidworks for Makers. Files included for your remixing. Print Settings Printer Brand: Prusa Printer: i3 MK4 **Rafts:** No Supports: Yes…
Replacement handle for Wok lid from Atlas Metal Spinning, SF California, USA Printed in PETG, however another material could be better for high temperature use. Since there are multiple curves on this part, you'll need to think about…
My wife has a ZKAPOR 2-in-1 Apple Watch charging cable. ( https://www.amazon.se/-/en/dp/B0D1DH7TF1?ref=ppx_yo2ov_dt_b_fed_asin_title ) While it works great, it has a very bright LED inside the watch charger which makes it difficult to…
To wszystkie aktualnie dostępne wyniki.
